Hi Haikun,
On 3/25/2015 8:35 PM, Haikun Wang wrote:
From: Haikun Wang <haikun.w...@freescale.com>
Atmel AT45DB series devices commands is different from common spi flash
commands. This patch add support for AT45DB special commands.
Add a flag AT45DB_CMD to control whether use those commands.
Signed-off-by: Haikun Wang <haikun.w...@freescale.com>
---
Changes in v1: None
drivers/mtd/spi/sf_internal.h | 7 +++++++
drivers/mtd/spi/sf_ops.c | 2 +-
drivers/mtd/spi/sf_probe.c | 10 ++++++++++
3 files changed, 18 insertions(+), 1 deletion(-)
diff --git a/drivers/mtd/spi/sf_internal.h b/drivers/mtd/spi/sf_internal.h
index 785f7a9..234af21 100644
--- a/drivers/mtd/spi/sf_internal.h
+++ b/drivers/mtd/spi/sf_internal.h
@@ -43,6 +43,7 @@ enum {
SST_BP = 1 << 3,
SST_WP = 1 << 4,
WR_QPP = 1 << 5,
+ AT45DB_CMD = 1 << 6,
};
#define SST_WR (SST_BP | SST_WP)
@@ -106,6 +107,12 @@ enum {
#define SPI_FLASH_PAGE_ERASE_TIMEOUT (5 * CONFIG_SYS_HZ)
#define SPI_FLASH_SECTOR_ERASE_TIMEOUT (10 * CONFIG_SYS_HZ)
+/* Atmel AT45DB specific */
+#define CMD_ATMEL_PAGE_PROGRAM 0x82
Why not use 0x2 to align with current mtd/spi framework?
+#define CMD_ATMEL_READ_STATUS 0xd7
+#define CMD_ATMEL_FLAG_STATUS 0xd7
+#define CMD_ATMEL_BLK_ERASE 0x50
+
/* SST specific */
#ifdef CONFIG_SPI_FLASH_SST
# define CMD_SST_BP 0x02 /* Byte Program */
diff --git a/drivers/mtd/spi/sf_ops.c b/drivers/mtd/spi/sf_ops.c
index 34bc54e..27ce5f9 100644
--- a/drivers/mtd/spi/sf_ops.c
+++ b/drivers/mtd/spi/sf_ops.c
@@ -165,7 +165,7 @@ int spi_flash_cmd_wait_ready(struct spi_flash *flash,
unsigned long timeout)
u8 poll_bit = STATUS_WIP;
u8 cmd = flash->poll_cmd;
- if (cmd == CMD_FLAG_STATUS) {
+ if (cmd == CMD_FLAG_STATUS || cmd == CMD_ATMEL_FLAG_STATUS) {
poll_bit = STATUS_PEC;
check_status = poll_bit;
}
diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c
index 4103723..2ccddf2 100644
--- a/drivers/mtd/spi/sf_probe.c
+++ b/drivers/mtd/spi/sf_probe.c
@@ -226,6 +226,16 @@ static int spi_flash_validate_params(struct spi_slave
*spi, u8 *idcode,
flash->poll_cmd = CMD_FLAG_STATUS;
#endif
+#ifdef CONFIG_SPI_FLASH_ATMEL
+ if (params->flags & AT45DB_CMD) {
+ flash->poll_cmd = CMD_ATMEL_READ_STATUS;
+ flash->write_cmd = CMD_ATMEL_PAGE_PROGRAM;
+ /* use block-erase command, eight pages */
+ flash->erase_cmd = CMD_ATMEL_BLK_ERASE;
+ flash->erase_size = flash->page_size * 8;
+ }
+#endif
+
The SPI Flash's default page size is 264 bytes, but mtd/spi framework
supports 256 and 512 bytes for one page. In your patch, you does not
handle such case, can your driver works as expected?
/* Configure the BAR - discover bank cmds and read current bank */
#ifdef CONFIG_SPI_FLASH_BAR
u8 curr_bank = 0;
Regards,
Peng.
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot