[U-Boot] [PATCH v3 06/15] cgtqmx6eval: Add ESDHC3 support

[Otavio Salvador]

cgtqmx6eval has an eMMC connected to ESDHC3.

Add support for it.

Signed-off-by: Otavio Salvador <ota...@ossystems.com.br>
---

Changes in v3: None
Changes in v2:
- Use ARRAY_SIZE(usdhc_cfg)
- Remove CONFIG_SYS_FSL_USDHC_NUM definition

 board/congatec/cgtqmx6eval/cgtqmx6eval.c | 22 +++++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

diff --git a/board/congatec/cgtqmx6eval/cgtqmx6eval.c 
b/board/congatec/cgtqmx6eval/cgtqmx6eval.c
index a740d95..e05060c 100644
--- a/board/congatec/cgtqmx6eval/cgtqmx6eval.c
+++ b/board/congatec/cgtqmx6eval/cgtqmx6eval.c
@@ -49,6 +49,20 @@ static iomux_v3_cfg_t const usdhc2_pads[] = {
        MX6_PAD_GPIO_4__GPIO1_IO04      | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 };
 
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+       MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+       MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
 static iomux_v3_cfg_t const usdhc4_pads[] = {
        MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
        MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -71,6 +85,7 @@ static void setup_iomux_uart(void)
 #ifdef CONFIG_FSL_ESDHC
 static struct fsl_esdhc_cfg usdhc_cfg[] = {
        {USDHC2_BASE_ADDR},
+       {USDHC3_BASE_ADDR},
        {USDHC4_BASE_ADDR},
 };
 
@@ -84,6 +99,9 @@ int board_mmc_getcd(struct mmc *mmc)
                gpio_direction_input(IMX_GPIO_NR(1, 4));
                ret = !gpio_get_value(IMX_GPIO_NR(1, 4));
                break;
+       case USDHC3_BASE_ADDR:
+               ret = 1;        /* eMMC is always present */
+               break;
        case USDHC4_BASE_ADDR:
                gpio_direction_input(IMX_GPIO_NR(2, 6));
                ret = !gpio_get_value(IMX_GPIO_NR(2, 6));
@@ -101,9 +119,11 @@ int board_mmc_init(bd_t *bis)
        int i;
 
        usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-       usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+       usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+       usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 
        imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+       imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
        imx_iomux_v3_setup_multiple_pads(usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
 
        for (i = 0; i < ARRAY_SIZE(usdhc_cfg); i++) {
-- 
2.4.6

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot