Pull the duplicate code out into a separate function.
Signed-off-by: Marek Vasut <[email protected]>
---
drivers/ddr/altera/sequencer.c | 74 +++++++++++++++++++++---------------------
1 file changed, 37 insertions(+), 37 deletions(-)
diff --git a/drivers/ddr/altera/sequencer.c b/drivers/ddr/altera/sequencer.c
index b2119a6..2d3f446 100644
--- a/drivers/ddr/altera/sequencer.c
+++ b/drivers/ddr/altera/sequencer.c
@@ -840,6 +840,37 @@ static void delay_for_n_mem_clocks(const uint32_t clocks)
debug("%s:%d clocks=%u ... end\n", __func__, __LINE__, clocks);
}
+/**
+ * rw_mgr_mem_init_load_regs() - Load instruction registers
+ * @cntr0: Counter 0 value
+ * @cntr1: Counter 1 value
+ * @cntr2: Counter 2 value
+ * @jump: Jump instruction value
+ *
+ * Load instruction registers.
+ */
+static void rw_mgr_mem_init_load_regs(u32 cntr0, u32 cntr1, u32 cntr2, u32
jump)
+{
+ uint32_t grpaddr = SDR_PHYGRP_RWMGRGRP_ADDRESS |
+ RW_MGR_RUN_SINGLE_GROUP_OFFSET;
+
+ /* Load counters */
+ writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(cntr0),
+ &sdr_rw_load_mgr_regs->load_cntr0);
+ writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(cntr1),
+ &sdr_rw_load_mgr_regs->load_cntr1);
+ writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(cntr2),
+ &sdr_rw_load_mgr_regs->load_cntr2);
+
+ /* Load jump address */
+ writel(jump, &sdr_rw_load_jump_mgr_regs->load_jump_add0);
+ writel(jump, &sdr_rw_load_jump_mgr_regs->load_jump_add1);
+ writel(jump, &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+
+ /* Execute count instruction */
+ writel(jump, grpaddr);
+}
+
static void rw_mgr_mem_initialize(void)
{
uint32_t r;
@@ -875,25 +906,9 @@ static void rw_mgr_mem_initialize(void)
* One possible solution is n = 0 , a = 256 , b = 106 => a = FF,
* b = 6A
*/
-
- /* Load counters */
- writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TINIT_CNTR0_VAL),
- &sdr_rw_load_mgr_regs->load_cntr0);
- writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TINIT_CNTR1_VAL),
- &sdr_rw_load_mgr_regs->load_cntr1);
- writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TINIT_CNTR2_VAL),
- &sdr_rw_load_mgr_regs->load_cntr2);
-
- /* Load jump address */
- writel(RW_MGR_INIT_RESET_0_CKE_0,
- &sdr_rw_load_jump_mgr_regs->load_jump_add0);
- writel(RW_MGR_INIT_RESET_0_CKE_0,
- &sdr_rw_load_jump_mgr_regs->load_jump_add1);
- writel(RW_MGR_INIT_RESET_0_CKE_0,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
-
- /* Execute count instruction */
- writel(RW_MGR_INIT_RESET_0_CKE_0, grpaddr);
+ rw_mgr_mem_init_load_regs(SEQ_TINIT_CNTR0_VAL, SEQ_TINIT_CNTR1_VAL,
+ SEQ_TINIT_CNTR2_VAL,
+ RW_MGR_INIT_RESET_0_CKE_0);
/* indicate that memory is stable */
writel(1, &phy_mgr_cfg->reset_mem_stbl);
@@ -912,24 +927,9 @@ static void rw_mgr_mem_initialize(void)
* One possible solution is n = 2 , a = 131 , b = 256 => a = 83,
* b = FF
*/
-
- /* Load counters */
- writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TRESET_CNTR0_VAL),
- &sdr_rw_load_mgr_regs->load_cntr0);
- writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TRESET_CNTR1_VAL),
- &sdr_rw_load_mgr_regs->load_cntr1);
- writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TRESET_CNTR2_VAL),
- &sdr_rw_load_mgr_regs->load_cntr2);
-
- /* Load jump address */
- writel(RW_MGR_INIT_RESET_1_CKE_0,
- &sdr_rw_load_jump_mgr_regs->load_jump_add0);
- writel(RW_MGR_INIT_RESET_1_CKE_0,
- &sdr_rw_load_jump_mgr_regs->load_jump_add1);
- writel(RW_MGR_INIT_RESET_1_CKE_0,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
-
- writel(RW_MGR_INIT_RESET_1_CKE_0, grpaddr);
+ rw_mgr_mem_init_load_regs(SEQ_TRESET_CNTR0_VAL, SEQ_TRESET_CNTR1_VAL,
+ SEQ_TRESET_CNTR2_VAL,
+ RW_MGR_INIT_RESET_1_CKE_0);
/* bring up clock enable */
--
2.1.4
_______________________________________________
U-Boot mailing list
[email protected]
http://lists.denx.de/mailman/listinfo/u-boot
