From: Tang Yuantian <[email protected]> Freescale ARM-based Layerscape LS102xA contain a SATA controller which comply with the serial ATA 3.0 specification and the AHCI 1.3 specification. This patch adds SATA feature on ls1021aqds and ls1021atwr boards.
Signed-off-by: Tang Yuantian <[email protected]> --- arch/arm/include/asm/arch-ls102xa/config.h | 15 ++++++ arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h | 24 +++++++++ board/freescale/ls1021aqds/ls1021aqds.c | 60 +++++++++++++++++++++++ board/freescale/ls1021atwr/ls1021atwr.c | 60 +++++++++++++++++++++++ 4 files changed, 159 insertions(+) diff --git a/arch/arm/include/asm/arch-ls102xa/config.h b/arch/arm/include/asm/arch-ls102xa/config.h index c55cdef..a4a5d84 100644 --- a/arch/arm/include/asm/arch-ls102xa/config.h +++ b/arch/arm/include/asm/arch-ls102xa/config.h @@ -79,6 +79,21 @@ #define CONFIG_SYS_PCIE2_PHYS_ADDR (CONFIG_SYS_PCIE2_PHYS_BASE + \ CONFIG_SYS_PCIE2_VIRT_ADDR) +/* SATA */ +#define AHCI_BASE_ADDR (CONFIG_SYS_IMMR + 0x02200000) +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_CMD_SCSI +#define CONFIG_LIBATA +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#define CONFIG_SYS_FSL_ERRATUM_A008407 + #ifdef CONFIG_DDR_SPD #define CONFIG_SYS_FSL_DDR_BE #define CONFIG_VERY_BIG_RAM diff --git a/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h b/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h index d34044a..211fe1d 100644 --- a/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h +++ b/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h @@ -397,4 +397,28 @@ struct ccsr_cci400 { u8 res_e004[0x10000 - 0xe004]; }; +/* AHCI (sata) register map */ +struct ccsr_ahci { + u32 res1[0xa4/4]; /* 0x0 - 0xa4 */ + u32 pcfg; /* port config */ + u32 ppcfg; /* port phy1 config */ + u32 pp2c; /* port phy2 config */ + u32 pp3c; /* port phy3 config */ + u32 pp4c; /* port phy4 config */ + u32 pp5c; /* port phy5 config */ + u32 paxic; /* port AXI config */ + u32 axicc; /* AXI cache control */ + u32 axipc; /* AXI PROT control */ + u32 ptc; /* port Trans Config */ + u32 pts; /* port Trans Status */ + u32 plc; /* port link config */ + u32 plc1; /* port link config1 */ + u32 plc2; /* port link config2 */ + u32 pls; /* port link status */ + u32 pls1; /* port link status1 */ + u32 pcmdc; /* port CMD config */ + u32 ppcs; /* port phy control status */ + u32 pberr; /* port 0/1 BIST error */ + u32 cmds; /* port 0/1 CMD status error */ +}; #endif /* __ASM_ARCH_LS102XA_IMMAP_H_ */ diff --git a/board/freescale/ls1021aqds/ls1021aqds.c b/board/freescale/ls1021aqds/ls1021aqds.c index ce5cb52..c7ac953 100644 --- a/board/freescale/ls1021aqds/ls1021aqds.c +++ b/board/freescale/ls1021aqds/ls1021aqds.c @@ -18,6 +18,8 @@ #include <fsl_ifc.h> #include <fsl_sec.h> #include <spl.h> +#include <ahci.h> +#include <scsi.h> #include "../common/sleep.h" #include "../common/qixis.h" @@ -54,6 +56,51 @@ enum { GE1_CLK125, }; +static void ls1021a_sata_init(void) +{ + struct ccsr_ahci __iomem *ccsr_ahci = (void *)AHCI_BASE_ADDR; + +#ifdef CONFIG_SYS_FSL_ERRATUM_A008407 + unsigned int __iomem *dcfg_ecc = (void *)0x20220520; +#endif + + out_le32(&ccsr_ahci->ppcfg, 0xa003fffe); + out_le32(&ccsr_ahci->pp2c, 0x28183411); + out_le32(&ccsr_ahci->pp3c, 0x0e081004); + out_le32(&ccsr_ahci->pp4c, 0x00480811); + out_le32(&ccsr_ahci->pp5c, 0x192c96a4); + out_le32(&ccsr_ahci->ptc, 0x08000025); + +#ifdef CONFIG_SYS_FSL_ERRATUM_A008407 + out_le32(dcfg_ecc, 0x00020000); +#endif +} + +#ifdef CONFIG_SCSI_AHCI_PLAT +static int ls1021a_sata_start(void) +{ + struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_FSL_GUTS_ADDR; + u32 cfg; + int rc = -1; + + cfg = in_be32(&gur->rcwsr[4]) & RCWSR4_SRDS1_PRTCL_MASK; + cfg >>= RCWSR4_SRDS1_PRTCL_SHIFT; + + if (cfg != 0x30 && cfg != 0x70) { + printf("SATA disabled: serdes protocol doesn't support\n"); + return rc; + } + + rc = ahci_init((void __iomem *)AHCI_BASE_ADDR); + if (rc) + return rc; + + scsi_scan(0); + + return 0; +} +#endif + int checkboard(void) { #ifndef CONFIG_QSPI_BOOT @@ -241,6 +288,8 @@ int board_early_init_f(void) fsl_dp_disable_console(); #endif + ls1021a_sata_init(); + return 0; } @@ -601,6 +650,17 @@ int board_init(void) return 0; } +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ +#ifdef CONFIG_SCSI_AHCI_PLAT + ls1021a_sata_start(); +#endif + + return 0; +} +#endif + #if defined(CONFIG_DEEP_SLEEP) void board_sleep_prepare(void) { diff --git a/board/freescale/ls1021atwr/ls1021atwr.c b/board/freescale/ls1021atwr/ls1021atwr.c index 8fef8e9..a3d3806 100644 --- a/board/freescale/ls1021atwr/ls1021atwr.c +++ b/board/freescale/ls1021atwr/ls1021atwr.c @@ -22,6 +22,8 @@ #include <tsec.h> #include <fsl_sec.h> #include <spl.h> +#include <ahci.h> +#include <scsi.h> #ifdef CONFIG_U_QE #include "../../../drivers/qe/qe.h" #endif @@ -86,6 +88,51 @@ struct cpld_data { u8 rev2; /* Reserved */ }; +static void ls1021a_sata_init(void) +{ + struct ccsr_ahci __iomem *ccsr_ahci = (void *)AHCI_BASE_ADDR; + +#ifdef CONFIG_SYS_FSL_ERRATUM_A008407 + unsigned int __iomem *dcfg_ecc = (void *)0x20220520; +#endif + + out_le32(&ccsr_ahci->ppcfg, 0xa003fffe); + out_le32(&ccsr_ahci->pp2c, 0x28183411); + out_le32(&ccsr_ahci->pp3c, 0x0e081004); + out_le32(&ccsr_ahci->pp4c, 0x00480811); + out_le32(&ccsr_ahci->pp5c, 0x192c96a4); + out_le32(&ccsr_ahci->ptc, 0x08000025); + +#ifdef CONFIG_SYS_FSL_ERRATUM_A008407 + out_le32(dcfg_ecc, 0x00020000); +#endif +} + +#ifdef CONFIG_SCSI_AHCI_PLAT +static int ls1021a_sata_start(void) +{ + struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_FSL_GUTS_ADDR; + u32 cfg; + int rc = -1; + + cfg = in_be32(&gur->rcwsr[4]) & RCWSR4_SRDS1_PRTCL_MASK; + cfg >>= RCWSR4_SRDS1_PRTCL_SHIFT; + + if (cfg != 0x10 && cfg != 0x30 && cfg != 0x70) { + printf("SATA disabled: serdes protocol doesn't support\n"); + return rc; + } + + rc = ahci_init((void __iomem *)AHCI_BASE_ADDR); + if (rc) + return rc; + + scsi_scan(0); + + return 0; +} +#endif + #ifndef CONFIG_QSPI_BOOT static void convert_serdes_mux(int type, int need_reset); @@ -388,6 +435,8 @@ int board_early_init_f(void) out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE); } + ls1021a_sata_init(); + return 0; } @@ -529,6 +578,17 @@ struct smmu_stream_id dev_stream_id[] = { { 0x18c, 0x0e, "DEBUG" }, }; +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ +#ifdef CONFIG_SCSI_AHCI_PLAT + ls1021a_sata_start(); +#endif + + return 0; +} +#endif + int board_init(void) { #ifndef CONFIG_SYS_FSL_NO_SERDES -- 2.1.0.27.g96db324 _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
