Hello Hans, Thanks for the review. On Sat, Nov 14, 2015 at 12:52 AM, Hans de Goede <hdego...@redhat.com> wrote:
> Hi, > > On 12-11-15 19:09, Vishnu Patekar wrote: > >> This patch series adds basic support for Allwinner A83T SOC. >> >> Allwinner A83T is octa-core cortex-a7 based SoC. >> It's clock control unit and prcm, pinmux are different from previous sun8i >> series. >> Its processor cores are arragned in two clusters 4 cores each, >> similar to A80. >> >> Only basic clocks are enabled pll1, pll5, pll6. >> SMP, display, other peripherals support is not yet supported. >> > > Cool stuff, great work! I've a number of comments, I will reply > to the individual patches with those. > > I've tried to get this to run on my own h8_homlet_v2 but > unfortunately I cannot get it to work. My own board does > boot into some chinese top-set-box environment when booting > without a sdcard and connected to a tv. But it does not show > any output on the uart connector at the bottom right of the > board (I've tried with 2 different adapters, including the > one from the Merrii A80 board which has the exact same connector > on the board). > > Not having an uart also means that I cannot get the board into > FEL mode (I do have a usb A <-> A cable). > > I wonder if my board has a broken uart, or if the system > image uses a different uart by default ? > As I observed, Device does not go to FEL mode if no USB A-A cable connected. Please connect USB cable and keep pressing 2,on uart with pins PFx and then power ON. It may help. > Have you tried booting with u-boot written to sdcard with > this patch-set ? Does this work, and does the SPL header > get printend on the bottom right uart connector ? > I broke A83T board microsd adapter badly. I've already ordered Onda 989 Air. Once I receive it, I'll test booting from microSD. Wens said it does not work for him. > Regards, > > Hans > > > > > This enables booting kernel with initramfs, kernel patch v1 have been sent. >> I'll send v2 with comments addressed. >> >> Vishnu Patekar (10): >> sunxi: Add Machine Support for A83T SOC >> sunxi: Add support for UART0 in PB pin group on A83T >> sunxi: power: axp818: add support for axp818 driver >> sunxi: power: enabled support for axp818 >> sunxi: do not enable smp for A83T >> sunxi: clk: add basic clocks for A83T >> sunxi: Add support for Allwinner A83T DRAM >> sunxi: do not include display for A83T >> sunxi: dts: sun8i: Add Allwinner A83T dtsi >> sunxi: Add suport for A83T HomletV2 Board by Allwinner >> >> arch/arm/cpu/armv7/sunxi/Makefile | 7 + >> arch/arm/cpu/armv7/sunxi/board.c | 8 +- >> arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c | 133 +++++++ >> arch/arm/cpu/armv7/sunxi/cpu_info.c | 2 + >> arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c | 424 >> +++++++++++++++++++++ >> arch/arm/cpu/armv7/sunxi/pmic_bus.c | 15 + >> arch/arm/dts/Makefile | 2 + >> arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 64 ++++ >> arch/arm/dts/sun8i-a83t.dtsi | 247 ++++++++++++ >> arch/arm/include/asm/arch-sunxi/clock.h | 4 +- >> arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 304 +++++++++++++++ >> arch/arm/include/asm/arch-sunxi/dram.h | 2 + >> arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h | 201 ++++++++++ >> arch/arm/include/asm/arch-sunxi/gpio.h | 1 + >> board/sunxi/Kconfig | 12 +- >> board/sunxi/MAINTAINERS | 5 + >> board/sunxi/board.c | 8 + >> configs/h8_homlet_v2_defconfig | 26 ++ >> drivers/power/Kconfig | 34 +- >> drivers/power/Makefile | 1 + >> drivers/power/axp818.c | 132 +++++++ >> include/axp818.h | 75 ++++ >> include/axp_pmic.h | 3 + >> include/configs/sun8i.h | 2 + >> include/configs/sunxi-common.h | 2 +- >> 25 files changed, 1698 insertions(+), 16 deletions(-) >> create mode 100644 arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c >> create mode 100644 arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c >> create mode 100644 arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts >> create mode 100644 arch/arm/dts/sun8i-a83t.dtsi >> create mode 100644 arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h >> create mode 100644 arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h >> create mode 100644 configs/h8_homlet_v2_defconfig >> create mode 100644 drivers/power/axp818.c >> create mode 100644 include/axp818.h >> >> _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
