Signed-off-by: Purna Chandra Mandal <[email protected]>
---
Changes in v2:
- drop unnecessary board_early_init_f()
- use LEAF(), END() macros for lowlevel_init
- move initialization of board_init_f() argument to common start.S
- move initdram() from board/microchip/ to mach-pic32/cpu.c
- remove MIPS virtual address in favor of physical address in dts file
arch/mips/cpu/start.S | 2 +
arch/mips/dts/pic32mzda.dtsi | 64 +++++++++++++
arch/mips/mach-pic32/Kconfig | 16 +++-
arch/mips/mach-pic32/Makefile | 2 +-
arch/mips/mach-pic32/cpu.c | 146 ++++++++++++++++++++++++++++++
arch/mips/mach-pic32/include/mach/pic32.h | 3 +
arch/mips/mach-pic32/lowlevel_init.S | 27 ++++++
arch/mips/mach-pic32/reset.c | 36 ++++++++
8 files changed, 294 insertions(+), 2 deletions(-)
create mode 100644 arch/mips/dts/pic32mzda.dtsi
create mode 100644 arch/mips/mach-pic32/lowlevel_init.S
create mode 100644 arch/mips/mach-pic32/reset.c
diff --git a/arch/mips/cpu/start.S b/arch/mips/cpu/start.S
index e95cdca..a7e6722 100644
--- a/arch/mips/cpu/start.S
+++ b/arch/mips/cpu/start.S
@@ -185,6 +185,8 @@ reset:
PTR_ADDU t0, k0, GD_MALLOC_BASE # gd->malloc_base offset
sw sp, 0(t0)
#endif
+ /* Initialize args to zero. */
+ li a0, 0x0
PTR_LA t9, board_init_f
jr t9
diff --git a/arch/mips/dts/pic32mzda.dtsi b/arch/mips/dts/pic32mzda.dtsi
new file mode 100644
index 0000000..f518ba8
--- /dev/null
+++ b/arch/mips/dts/pic32mzda.dtsi
@@ -0,0 +1,64 @@
+/*
+ * Copyright 2015 Microchip Technology, Inc.
+ * Purna Chandra Mandal, <[email protected]>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/microchip,clock.h>
+#include "skeleton.dtsi"
+
+/ {
+ compatible = "microchip,pic32mzda", "microchip,pic32mz";
+
+ cpus {
+ cpu@0 {
+ compatible = "mips,mips14kc";
+ };
+ };
+
+ clock: clk@1f801200 {
+ compatible = "microchip,pic32mzda_clk";
+ reg = <0x1f801200 0x1000>;
+ clock-cells = <1>;
+ };
+
+ uart1: serial@1f822000 {
+ compatible = "microchip,pic32mzda-uart";
+ reg = <0x1f822000 0x50>;
+ interrupts = <112 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ clocks = <&clock PB2CLK>;
+ };
+
+ uart2: serial@1f822200 {
+ compatible = "microchip,pic32mzda-uart";
+ reg = <0x1f822200 0x50>;
+ interrupts = <145 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clock PB2CLK>;
+ status = "disabled";
+ };
+
+ uart6: serial@1f822a00 {
+ compatible = "microchip,pic32mzda-uart";
+ reg = <0x1f822a00 0x50>;
+ interrupts = <188 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clock PB2CLK>;
+ status = "disabled";
+ };
+
+ evic: interrupt-controller@1f810000 {
+ compatible = "microchip,pic32mzda-evic";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x1f810000 0x1000>;
+ };
+
+ pinctrl: pinctrl@1f801400 {
+ compatible = "microchip,pic32mzda-pinctrl";
+ reg = <0x1f801400 0x100>, /* in */
+ <0x1f801500 0x200>; /* out */
+ status = "disabled";
+ };
+};
diff --git a/arch/mips/mach-pic32/Kconfig b/arch/mips/mach-pic32/Kconfig
index 98b0b88..a394791 100644
--- a/arch/mips/mach-pic32/Kconfig
+++ b/arch/mips/mach-pic32/Kconfig
@@ -2,11 +2,25 @@ menu "Microchip PIC32 platforms"
depends on MACH_PIC32
config SYS_SOC
- default "none"
+ default "pic32mzda" if SOC_PIC32MZDA
choice
prompt "PIC32 SoC select"
+config SOC_PIC32MZDA
+ bool "Microchip PIC32MZ[DA] family"
+ select SUPPORTS_LITTLE_ENDIAN
+ select SUPPORTS_CPU_MIPS32_R1
+ select SUPPORTS_CPU_MIPS32_R2
+ select SYS_MIPS_CACHE_INIT_RAM_LOAD
+ select MIPS_BOOT_CMDLINE_LEGACY
+ select MIPS_BOOT_FDT
+ select DM_SERIAL
+ select PIC32_SERIAL
+ select PIC32_PINCTRL
+ help
+ This supports Microchip PIC32MZ[DA] family of microcontrollers.
+
endchoice
choice
diff --git a/arch/mips/mach-pic32/Makefile b/arch/mips/mach-pic32/Makefile
index cb42607..e321e65 100644
--- a/arch/mips/mach-pic32/Makefile
+++ b/arch/mips/mach-pic32/Makefile
@@ -4,4 +4,4 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y = cpu.o
+obj-y = cpu.o lowlevel_init.o reset.o
\ No newline at end of file
diff --git a/arch/mips/mach-pic32/cpu.c b/arch/mips/mach-pic32/cpu.c
index 58fd3ab..7bd0f07 100644
--- a/arch/mips/mach-pic32/cpu.c
+++ b/arch/mips/mach-pic32/cpu.c
@@ -6,8 +6,154 @@
*
*/
#include <common.h>
+#include <dm.h>
+#include <clk.h>
+#include <debug_uart.h>
+#include <linux/compiler.h>
+#include <asm/io.h>
+#include <asm/mipsregs.h>
+#include <mach/pic32.h>
+#include <mach/ddr.h>
+#include <dt-bindings/clock/microchip,clock.h>
+/* Flash prefetch */
+#define PRECON 0x00
+#define PRECONCLR (PRECON + _CLR_OFFSET)
+#define PRECONSET (PRECON + _SET_OFFSET)
+
+/* Flash ECCCON */
+#define ECC_MASK 0x03
+#define ECC_SHIFT 4
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static ulong clk_get_cpu_rate(void)
+{
+ int ret;
+ struct udevice *dev;
+
+ ret = uclass_get_device(UCLASS_CLK, 0, &dev);
+ if (ret) {
+ panic("uclass-clk: device not found\n");
+ return 0;
+ }
+
+ return clk_get_rate(dev);
+}
+
+/* initialize prefetch module related to cpu_clk */
+static void init_prefetch(void)
+{
+#define _MHZ(x) ((x) * 1000000)
+ void __iomem *base;
+ int v, nr_waits;
+ ulong rate;
+
+ rate = clk_get_cpu_rate();
+
+ /* get flash ECC type */
+ base = pic32_ioremap(PIC32_CFG_BASE);
+ v = (readl(base + CFGCON) >> ECC_SHIFT) & ECC_MASK;
+ if (v < 2) {
+ if (rate < _MHZ(66))
+ nr_waits = 0;
+ else if (rate < _MHZ(133))
+ nr_waits = 1;
+ else
+ nr_waits = 2;
+ } else {
+ if (rate <= _MHZ(83))
+ nr_waits = 0;
+ else if (rate <= _MHZ(166))
+ nr_waits = 1;
+ else
+ nr_waits = 2;
+ }
+
+ base = pic32_ioremap(PREFETCH_BASE);
+ writel(nr_waits, base + PRECON);
+
+ /* Enable prefetch for all */
+ writel(0x30, base + PRECONSET);
+#undef _MHZ
+}
+
+/* arch specific CPU init after DM */
+int arch_cpu_init_dm(void)
+{
+ /* flash prefetch */
+ init_prefetch();
+ return 0;
+}
+
+/* Un-gate DDR2 modules (gated by default) */
+static void ddr2_pmd_ungate(void)
+{
+ void __iomem *regs;
+
+ regs = pic32_ioremap(PIC32_CFG_BASE);
+ writel(0, regs + PMD7);
+}
+
+/* initialize the DDR2 Controller and DDR2 PHY */
phys_size_t initdram(int board_type)
{
+ ddr2_pmd_ungate();
+ ddr2_phy_init();
+ ddr2_ctrl_init();
+ return ddr2_calculate_size();
+}
+
+int misc_init_r(void)
+{
+ set_io_port_base(0);
+ return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+const char *get_core_name(void)
+{
+ u32 proc_id;
+ const char *str;
+
+ proc_id = read_c0_prid();
+ switch (proc_id) {
+ case 0x19e28:
+ str = "PIC32MZ[DA]";
+ break;
+ default:
+ str = "UNKNOWN";
+ }
+
+ return str;
+}
+#endif
+
+#ifdef CONFIG_CMD_CLK
+int soc_clk_dump(void)
+{
+#define F_MHZ(x) ((x) / 1000000)
+ int i, ret;
+ struct udevice *dev;
+
+ ret = uclass_get_device(UCLASS_CLK, 0, &dev);
+ if (ret) {
+ printf("clk-uclass not found\n");
+ return ret;
+ }
+
+ printf("PLL Speed: %lu MHz\n", F_MHZ(clk_get_periph_rate(dev, PLLCLK)));
+ printf("CPU Speed: %lu MHz\n", F_MHZ(clk_get_rate(dev)));
+ printf("MPLL Speed: %lu MHz\n", F_MHZ(clk_get_periph_rate(dev, MPLL)));
+
+ for (i = PB1CLK; i <= PB7CLK; i++)
+ printf("PB%d Clock Speed: %lu MHz\n",
+ i - PB1CLK + 1, F_MHZ(clk_get_periph_rate(dev, i)));
+
+ for (i = REF1CLK; i <= REF5CLK; i++)
+ printf("REFO%d Clock Speed: %lu MHz\n", i - REF1CLK + 1,
+ F_MHZ(clk_get_periph_rate(dev, i)));
+#undef F_MHZ
return 0;
}
+#endif
diff --git a/arch/mips/mach-pic32/include/mach/pic32.h
b/arch/mips/mach-pic32/include/mach/pic32.h
index f618697..8d4b275 100644
--- a/arch/mips/mach-pic32/include/mach/pic32.h
+++ b/arch/mips/mach-pic32/include/mach/pic32.h
@@ -76,4 +76,7 @@ static inline void __iomem *pic32_ioremap(phys_addr_t addr)
return (void __iomem *)CKSEG1ADDR(addr);
}
+/* Core */
+const char *get_core_name(void);
+
#endif /* __PIC32_REGS_H__ */
diff --git a/arch/mips/mach-pic32/lowlevel_init.S
b/arch/mips/mach-pic32/lowlevel_init.S
new file mode 100644
index 0000000..bff5553
--- /dev/null
+++ b/arch/mips/mach-pic32/lowlevel_init.S
@@ -0,0 +1,27 @@
+/*
+ * (c) 2015 Purna Chandra Mandal <[email protected]>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+*/
+
+#include <config.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/asm.h>
+
+LEAF(lowlevel_init)
+ /*
+ * Establish Cause
+ * (set IV bit)
+ */
+ li t1, 0x00800000
+ mtc0 t1, CP0_CAUSE
+
+ /* Establish Wired (and Random) */
+ mtc0 zero, CP0_WIRED
+ nop
+
+ jr ra
+ nop
+ END(lowlevel_init)
diff --git a/arch/mips/mach-pic32/reset.c b/arch/mips/mach-pic32/reset.c
new file mode 100644
index 0000000..70467cb
--- /dev/null
+++ b/arch/mips/mach-pic32/reset.c
@@ -0,0 +1,36 @@
+/*
+ * (c) 2015 Purna Chandra Mandal <[email protected]>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <mach/pic32.h>
+
+#define SYSKEY 0x0030
+#define UNLOCK_KEY1 0xaa996655
+#define UNLOCK_KEY2 0x556699aa
+#define LOCK_KEY 0
+
+#define RSWRST 0x1250
+
+void _machine_restart(void)
+{
+ void __iomem *base;
+
+ base = pic32_ioremap(PIC32_CFG_BASE);
+
+ /* unlock sequence */
+ writel(LOCK_KEY, base + SYSKEY);
+ writel(UNLOCK_KEY1, base + SYSKEY);
+ writel(UNLOCK_KEY2, base + SYSKEY);
+
+ /* soft reset */
+ writel(0x1, base + RSWRST);
+ (void) readl(base + RSWRST);
+
+ while (1)
+ ;
+}
--
1.8.3.1
_______________________________________________
U-Boot mailing list
[email protected]
http://lists.denx.de/mailman/listinfo/u-boot
