ulpi_read and ulpi_write are used to read/write registers via ULPI bus.
Code generates compilation warnings on 64-bit machines where pointer
is cast to u32.
This patch drops all but last 8 bits of register address.
It is possible, because addresses on ULPI bus are 6- or 8-bit.
It is not possible (according to ULPI 1.1 spec) to have more
than 8-bit addressing.
This patch should not cause regressions as all calls to
ulpi_read/write use either structure pointer (@ address 0) or integer
offsets cast to pointer - addresses requested are way below 8-bit range.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikow...@gmail.com>
Acked-by: Marek Vasut <ma...@denx.de>
---
Changes in v4:
- Add Ack from Marek
Changes in v3:
- New patch
Changes in v2: None
Changes in v1: None
drivers/usb/ulpi/ulpi-viewport.c | 5 +++--
include/usb/ulpi.h | 2 ++
2 files changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/usb/ulpi/ulpi-viewport.c b/drivers/usb/ulpi/ulpi-viewport.c
index 72a06de..d111680 100644
--- a/drivers/usb/ulpi/ulpi-viewport.c
+++ b/drivers/usb/ulpi/ulpi-viewport.c
@@ -92,7 +92,8 @@ static int ulpi_request(struct ulpi_viewport *ulpi_vp, u32
value)
int ulpi_write(struct ulpi_viewport *ulpi_vp, u8 *reg, u32 value)
{
- u32 val = ULPI_RWRUN | ULPI_RWCTRL | ((u32)reg << 16) | (value & 0xff);
+ u32 addr = (uintptr_t)reg & 0xFF;
+ u32 val = ULPI_RWRUN | ULPI_RWCTRL | addr << 16 | (value & 0xff);
val |= (ulpi_vp->port_num & 0x7) << 24;
return ulpi_request(ulpi_vp, val);
@@ -101,7 +102,7 @@ int ulpi_write(struct ulpi_viewport *ulpi_vp, u8 *reg, u32
value)
u32 ulpi_read(struct ulpi_viewport *ulpi_vp, u8 *reg)
{
int err;
- u32 val = ULPI_RWRUN | ((u32)reg << 16);
+ u32 val = ULPI_RWRUN | ((uintptr_t)reg & 0xFF) << 16;
val |= (ulpi_vp->port_num & 0x7) << 24;
err = ulpi_request(ulpi_vp, val);
diff --git a/include/usb/ulpi.h b/include/usb/ulpi.h
index dfea395..747fb0a 100644
--- a/include/usb/ulpi.h
+++ b/include/usb/ulpi.h
@@ -123,6 +123,7 @@ int ulpi_reset(struct ulpi_viewport *ulpi_vp);
/*
* Write to the ULPI PHY register via the viewport.
* @reg - the ULPI register (one of the fields in struct
ulpi_regs).
+ * Due to ULPI design, only 8 lsb of address are used.
* @value - the value - only 8 lower bits are used, others ignored.
*
* returns 0 on success, ULPI_ERROR on failure.
@@ -132,6 +133,7 @@ int ulpi_write(struct ulpi_viewport *ulpi_vp, u8 *reg, u32
value);
/*
* Read the ULPI PHY register content via the viewport.
* @reg - the ULPI register (one of the fields in struct
ulpi_regs).
+ * Due to ULPI design, only 8 lsb of address are used.
*
* returns register content on success, ULPI_ERROR on failure.
*/
--
2.5.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
