From: Mingkai Hu <mingkai...@nxp.com>
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
SATA:
* SerDes2 Lane3 to SATA port
USB 3.0: one super speed USB 3.0 type A port
one Micro-AB port
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <mingkai...@nxp.com>
Signed-off-by: Shaohui Xie <shaohui....@nxp.com>
Signed-off-by: Gong Qianyu <qianyu.g...@nxp.com>
---
v6:
- Move CONFIG_FSL_QSPI to defconfig and select DM_SPI_FLASH in Kconfig.
v5:
- Adjust the SPL BSS and MALLOC address.
v4:
- Extend SPL max size and pad_to size for SD boot.
v3:
- Remove redundant sd rcw .cfg files.
- Adjust the format of memory map.
- Add emmc boot support.
v2:
- Add >60 characters' paragraph for the board help.
- Fix the memory map in readme.
- Remove unused flash r/w functions.
- Remove DDR3 defines.
arch/arm/Kconfig | 13 ++
arch/arm/dts/Makefile | 1 +
arch/arm/dts/fsl-ls1046a-rdb.dts | 44 ++++
arch/arm/dts/fsl-ls1046a.dtsi | 166 ++++++++++++++
board/freescale/ls1046ardb/Kconfig | 16 ++
board/freescale/ls1046ardb/MAINTAINERS | 9 +
board/freescale/ls1046ardb/Makefile | 10 +
board/freescale/ls1046ardb/README | 76 +++++++
board/freescale/ls1046ardb/cpld.c | 158 ++++++++++++++
board/freescale/ls1046ardb/cpld.h | 49 +++++
board/freescale/ls1046ardb/ddr.c | 140 ++++++++++++
board/freescale/ls1046ardb/ddr.h | 44 ++++
board/freescale/ls1046ardb/eth.c | 77 +++++++
board/freescale/ls1046ardb/ls1046ardb.c | 136 ++++++++++++
board/freescale/ls1046ardb/ls1046ardb_pbi.cfg | 22 ++
board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg | 7 +
board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg | 7 +
configs/ls1046ardb_emmc_defconfig | 26 +++
configs/ls1046ardb_qspi_defconfig | 25 +++
configs/ls1046ardb_sdcard_defconfig | 26 +++
include/configs/ls1046a_common.h | 175 +++++++++++++++
include/configs/ls1046ardb.h | 240 +++++++++++++++++++++
22 files changed, 1467 insertions(+)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c871eaf..8c59c42 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -837,6 +837,18 @@ config TARGET_LS1043ARDB
help
Support for Freescale LS1043ARDB platform.
+config TARGET_LS1046ARDB
+ bool "Support ls1046ardb"
+ select ARM64
+ select ARMV8_MULTIENTRY
+ select SUPPORT_SPL
+ select DM_SPI_FLASH if DM_SPI
+ help
+ Support for Freescale LS1046ARDB platform.
+ The LS1046A Reference Design Board (RDB) is a high-performance
+ development platform that supports the QorIQ LS1046A
+ Layerscape Architecture processor.
+
config TARGET_H2200
bool "Support h2200"
select CPU_PXA
@@ -981,6 +993,7 @@ source "board/freescale/ls1021aqds/Kconfig"
source "board/freescale/ls1043aqds/Kconfig"
source "board/freescale/ls1021atwr/Kconfig"
source "board/freescale/ls1043ardb/Kconfig"
+source "board/freescale/ls1046ardb/Kconfig"
source "board/freescale/ls1012aqds/Kconfig"
source "board/freescale/ls1012ardb/Kconfig"
source "board/freescale/ls1012afrdm/Kconfig"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 756535b..b646aa0 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -143,6 +143,7 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
fsl-ls1043a-qds-lpuart.dtb \
fsl-ls1043a-rdb.dtb \
+ fsl-ls1046a-rdb.dtb \
fsl-ls1012a-qds.dtb \
fsl-ls1012a-rdb.dtb \
fsl-ls1012a-frdm.dtb
diff --git a/arch/arm/dts/fsl-ls1046a-rdb.dts b/arch/arm/dts/fsl-ls1046a-rdb.dts
new file mode 100644
index 0000000..4902454
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1046a-rdb.dts
@@ -0,0 +1,44 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * Mingkai Hu <mingkai...@freescale.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+/include/ "fsl-ls1046a.dtsi"
+
+/ {
+ model = "LS1046A RDB Board";
+
+ aliases {
+ spi0 = &qspi;
+ };
+
+};
+
+&qspi {
+ bus-num = <0>;
+ status = "okay";
+
+ qflash0: s25fs512s@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+
+ qflash1: s25fs512s@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <1>;
+ };
+};
diff --git a/arch/arm/dts/fsl-ls1046a.dtsi b/arch/arm/dts/fsl-ls1046a.dtsi
new file mode 100644
index 0000000..87dd997
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1046a.dtsi
@@ -0,0 +1,166 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright (C) 2016, Freescale Semiconductor
+ *
+ * Mingkai Hu <mingkai...@nxp.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/include/ "skeleton64.dtsi"
+
+/ {
+ compatible = "fsl,ls1046a";
+ interrupt-parent = <&gic>;
+
+ sysclk: sysclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "sysclk";
+ };
+
+ gic: interrupt-controller@1400000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x0 0x1410000 0 0x10000>, /* GICD */
+ <0x0 0x1420000 0 0x10000>, /* GICC */
+ <0x0 0x1440000 0 0x20000>, /* GICH */
+ <0x0 0x1460000 0 0x20000>; /* GICV */
+ interrupts = <1 9 0xf08>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clockgen: clocking@1ee1000 {
+ compatible = "fsl,ls1046a-clockgen";
+ reg = <0x0 0x1ee1000 0x0 0x1000>;
+ #clock-cells = <2>;
+ clocks = <&sysclk>;
+ };
+
+ dspi0: dspi@2100000 {
+ compatible = "fsl,vf610-dspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2100000 0x0 0x10000>;
+ interrupts = <0 64 0x4>;
+ clock-names = "dspi";
+ clocks = <&clockgen 4 0>;
+ num-cs = <6>;
+ big-endian;
+ status = "disabled";
+ };
+
+ dspi1: dspi@2110000 {
+ compatible = "fsl,vf610-dspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2110000 0x0 0x10000>;
+ interrupts = <0 65 0x4>;
+ clock-names = "dspi";
+ clocks = <&clockgen 4 0>;
+ num-cs = <6>;
+ big-endian;
+ status = "disabled";
+ };
+
+ ifc: ifc@1530000 {
+ compatible = "fsl,ifc", "simple-bus";
+ reg = <0x0 0x1530000 0x0 0x10000>;
+ interrupts = <0 43 0x4>;
+ };
+
+ i2c0: i2c@2180000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2180000 0x0 0x10000>;
+ interrupts = <0 56 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@2190000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2190000 0x0 0x10000>;
+ interrupts = <0 57 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@21a0000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x21a0000 0x0 0x10000>;
+ interrupts = <0 58 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@21b0000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x21b0000 0x0 0x10000>;
+ interrupts = <0 59 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ duart0: serial@21c0500 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0500 0x0 0x100>;
+ interrupts = <0 54 0x4>;
+ clocks = <&clockgen 4 0>;
+ };
+
+ duart1: serial@21c0600 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0600 0x0 0x100>;
+ interrupts = <0 54 0x4>;
+ clocks = <&clockgen 4 0>;
+ };
+
+ duart2: serial@21d0500 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21d0500 0x0 0x100>;
+ interrupts = <0 55 0x4>;
+ clocks = <&clockgen 4 0>;
+ };
+
+ duart3: serial@21d0600 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21d0600 0x0 0x100>;
+ interrupts = <0 55 0x4>;
+ clocks = <&clockgen 4 0>;
+ };
+
+ qspi: quadspi@1550000 {
+ compatible = "fsl,vf610-qspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x1550000 0x0 0x10000>,
+ <0x0 0x40000000 0x0 0x10000000>;
+ reg-names = "QuadSPI", "QuadSPI-memory";
+ num-cs = <4>;
+ big-endian;
+ status = "disabled";
+ };
+ };
+};
diff --git a/board/freescale/ls1046ardb/Kconfig
b/board/freescale/ls1046ardb/Kconfig
new file mode 100644
index 0000000..a62255c
--- /dev/null
+++ b/board/freescale/ls1046ardb/Kconfig
@@ -0,0 +1,16 @@
+
+if TARGET_LS1046ARDB
+
+config SYS_BOARD
+ default "ls1046ardb"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "ls1046ardb"
+
+endif
diff --git a/board/freescale/ls1046ardb/MAINTAINERS
b/board/freescale/ls1046ardb/MAINTAINERS
new file mode 100644
index 0000000..ff42bef
--- /dev/null
+++ b/board/freescale/ls1046ardb/MAINTAINERS
@@ -0,0 +1,9 @@
+LS1046A BOARD
+M: Mingkai Hu <mingkai...@nxp.com>
+S: Maintained
+F: board/freescale/ls1046ardb/
+F: board/freescale/ls1046ardb/ls1046ardb.c
+F: include/configs/ls1046ardb.h
+F: configs/ls1046ardb_qspi_defconfig
+F: configs/ls1046ardb_sdcard_defconfig
+F: configs/ls1046ardb_emmc_defconfig
diff --git a/board/freescale/ls1046ardb/Makefile
b/board/freescale/ls1046ardb/Makefile
new file mode 100644
index 0000000..348eb76
--- /dev/null
+++ b/board/freescale/ls1046ardb/Makefile
@@ -0,0 +1,10 @@
+#
+# Copyright 2016 Freescale Semiconductor
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += cpld.o
+obj-y += ddr.o
+obj-y += ls1046ardb.o
+obj-$(CONFIG_SYS_DPAA_FMAN) += eth.o
diff --git a/board/freescale/ls1046ardb/README
b/board/freescale/ls1046ardb/README
new file mode 100644
index 0000000..1ef7d47
--- /dev/null
+++ b/board/freescale/ls1046ardb/README
@@ -0,0 +1,76 @@
+Overview
+--------
+The LS1046A Reference Design Board (RDB) is a high-performance computing,
+evaluation, and development platform that supports the QorIQ LS1046A
+LayerScape Architecture processor. The LS1046ARDB provides SW development
+platform for the Freescale LS1046A processor series, with a complete
+debugging environment. The LS1046A RDB is lead-free and RoHS-compliant.
+
+LS1046A SoC Overview
+--------------------
+Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS1046A
+SoC overview.
+
+ LS1046ARDB board Overview
+ -----------------------
+ - SERDES1 Connections, 4 lanes supporting:
+ - Lane0: XFI with x1 RJ45 connector
+ - Lane1: XFI Cage
+ - Lane2: SGMII.5
+ - Lane3: SGMII.6
+ - SERDES2 Connections, 4 lanes supporting:
+ - Lane0: PCIe1 with miniPCIe slot
+ - Lane1: PCIe2 with PCIe x2 slot
+ - Lane2: PCIe3 with PCIe x4 slot
+ - Lane3: SATA
+ - DDR Controller
+ - 8GB 64bits DDR4 SDRAM. Support rates of up to 2133MT/s
+ -IFC/Local Bus
+ - One 512 MB NAND flash with ECC support
+ - CPLD connection
+ - USB 3.0
+ - one Type A port, one Micro-AB port
+ - SDHC: connects directly to a full SD/MMC slot
+ - DSPI: 64 MB high-speed flash Memory for boot code and storage (up to 108MHz)
+ - 4 I2C controllers
+ - UART
+ - Two 4-pin serial ports at up to 115.2 Kbit/s
+ - Two DB9 D-Type connectors supporting one Serial port each
+ - ARM JTAG support
+
+Memory map from core's view
+----------------------------
+Start Address End Address Description Size
+0x00_0000_0000 - 0x00_000F_FFFF Secure Boot ROM 1MB
+0x00_0100_0000 - 0x00_0FFF_FFFF CCSRBAR 240MB
+0x00_1000_0000 - 0x00_1000_FFFF OCRAM0 64KB
+0x00_1001_0000 - 0x00_1001_FFFF OCRAM1 64KB
+0x00_2000_0000 - 0x00_20FF_FFFF DCSR 16MB
+0x00_7E80_0000 - 0x00_7E80_FFFF IFC - NAND Flash 64KB
+0x00_7FB0_0000 - 0x00_7FB0_0FFF IFC - CPLD 4KB
+0x00_8000_0000 - 0x00_FFFF_FFFF DRAM1 2GB
+0x05_0000_0000 - 0x05_07FF_FFFF QMAN S/W Portal 128M
+0x05_0800_0000 - 0x05_0FFF_FFFF BMAN S/W Portal 128M
+0x08_8000_0000 - 0x09_FFFF_FFFF DRAM2 6GB
+0x40_0000_0000 - 0x47_FFFF_FFFF PCI Express1 32G
+0x48_0000_0000 - 0x4F_FFFF_FFFF PCI Express2 32G
+0x50_0000_0000 - 0x57_FFFF_FFFF PCI Express3 32G
+
+QSPI flash map:
+Start Address End Address Description Size
+0x00_4000_0000 - 0x00_400F_FFFF RCW + PBI 1MB
+0x00_4010_0000 - 0x00_401F_FFFF U-Boot 1MB
+0x00_4020_0000 - 0x00_402F_FFFF U-Boot Env 1MB
+0x00_4030_0000 - 0x00_403F_FFFF FMan ucode 1MB
+0x00_4040_0000 - 0x00_404F_FFFF UEFI 1MB
+0x00_4050_0000 - 0x00_406F_FFFF PPA 2MB
+0x00_4070_0000 - 0x00_408F_FFFF Secure boot header
+ + bootscript 2MB
+0x00_4090_0000 - 0x00_40FF_FFFF Reserved 7MB
+0x00_4100_0000 - 0x00_43FF_FFFF FIT Image 48MB
+
+Booting Options
+---------------
+a) QSPI boot
+b) SD boot
+c) eMMC boot
diff --git a/board/freescale/ls1046ardb/cpld.c
b/board/freescale/ls1046ardb/cpld.c
new file mode 100644
index 0000000..81a646e
--- /dev/null
+++ b/board/freescale/ls1046ardb/cpld.c
@@ -0,0 +1,158 @@
+/*
+ * Copyright 2016 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Freescale LS1046ARDB board-specific CPLD controlling supports.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+#include "cpld.h"
+
+u8 cpld_read(unsigned int reg)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ return in_8(p + reg);
+}
+
+void cpld_write(unsigned int reg, u8 value)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ out_8(p + reg, value);
+}
+
+/* Set the boot bank to the alternate bank */
+void cpld_set_altbank(void)
+{
+ u16 reg = CPLD_CFG_RCW_SRC_QSPI;
+ u8 reg4 = CPLD_READ(soft_mux_on);
+ u8 reg5 = (u8)(reg >> 1);
+ u8 reg6 = (u8)(reg & 1);
+ u8 reg7 = CPLD_READ(vbank);
+
+ cpld_rev_bit(®5);
+
+ CPLD_WRITE(soft_mux_on, reg4 | CPLD_SW_MUX_BANK_SEL | 1);
+
+ CPLD_WRITE(cfg_rcw_src1, reg5);
+ CPLD_WRITE(cfg_rcw_src2, reg6);
+
+ reg7 = (reg7 & ~CPLD_BANK_SEL_MASK) | CPLD_BANK_SEL_ALTBANK;
+ CPLD_WRITE(vbank, reg7);
+
+ CPLD_WRITE(system_rst, 1);
+}
+
+/* Set the boot bank to the default bank */
+void cpld_set_defbank(void)
+{
+ u16 reg = CPLD_CFG_RCW_SRC_QSPI;
+ u8 reg4 = CPLD_READ(soft_mux_on);
+ u8 reg5 = (u8)(reg >> 1);
+ u8 reg6 = (u8)(reg & 1);
+
+ cpld_rev_bit(®5);
+
+ CPLD_WRITE(soft_mux_on, reg4 | CPLD_SW_MUX_BANK_SEL | 1);
+
+ CPLD_WRITE(cfg_rcw_src1, reg5);
+ CPLD_WRITE(cfg_rcw_src2, reg6);
+
+ CPLD_WRITE(vbank, 0);
+
+ CPLD_WRITE(system_rst, 1);
+}
+
+void cpld_set_sd(void)
+{
+ u16 reg = CPLD_CFG_RCW_SRC_SD;
+ u8 reg5 = (u8)(reg >> 1);
+ u8 reg6 = (u8)(reg & 1);
+
+ cpld_rev_bit(®5);
+
+ CPLD_WRITE(soft_mux_on, 1);
+
+ CPLD_WRITE(cfg_rcw_src1, reg5);
+ CPLD_WRITE(cfg_rcw_src2, reg6);
+
+ CPLD_WRITE(system_rst, 1);
+}
+#ifdef DEBUG
+static void cpld_dump_regs(void)
+{
+ printf("cpld_ver = %x\n", CPLD_READ(cpld_ver));
+ printf("cpld_ver_sub = %x\n", CPLD_READ(cpld_ver_sub));
+ printf("pcba_ver = %x\n", CPLD_READ(pcba_ver));
+ printf("soft_mux_on = %x\n", CPLD_READ(soft_mux_on));
+ printf("cfg_rcw_src1 = %x\n", CPLD_READ(cfg_rcw_src1));
+ printf("cfg_rcw_src2 = %x\n", CPLD_READ(cfg_rcw_src2));
+ printf("vbank = %x\n", CPLD_READ(vbank));
+ printf("sysclk_sel = %x\n", CPLD_READ(sysclk_sel));
+ printf("uart_sel = %x\n", CPLD_READ(uart_sel));
+ printf("sd1refclk_sel = %x\n", CPLD_READ(sd1refclk_sel));
+ printf("rgmii_1588_sel = %x\n", CPLD_READ(rgmii_1588_sel));
+ printf("1588_clk_sel = %x\n", CPLD_READ(reg_1588_clk_sel));
+ printf("status_led = %x\n", CPLD_READ(status_led));
+ printf("sd_emmc = %x\n", CPLD_READ(sd_emmc));
+ printf("vdd_en = %x\n", CPLD_READ(vdd_en));
+ printf("vdd_sel = %x\n", CPLD_READ(vdd_sel));
+ putc('\n');
+}
+#endif
+
+void cpld_rev_bit(unsigned char *value)
+{
+ u8 rev_val, val;
+ int i;
+
+ val = *value;
+ rev_val = val & 1;
+ for (i = 1; i <= 7; i++) {
+ val >>= 1;
+ rev_val <<= 1;
+ rev_val |= val & 1;
+ }
+
+ *value = rev_val;
+}
+
+int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int rc = 0;
+
+ if (argc <= 1)
+ return cmd_usage(cmdtp);
+
+ if (strcmp(argv[1], "reset") == 0) {
+ if (strcmp(argv[2], "altbank") == 0)
+ cpld_set_altbank();
+ else if (strcmp(argv[2], "sd") == 0)
+ cpld_set_sd();
+ else
+ cpld_set_defbank();
+#ifdef DEBUG
+ } else if (strcmp(argv[1], "dump") == 0) {
+ cpld_dump_regs();
+#endif
+ } else {
+ rc = cmd_usage(cmdtp);
+ }
+
+ return rc;
+}
+
+U_BOOT_CMD(
+ cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
+ "Reset the board or alternate bank",
+ "reset: reset to default bank\n"
+ "cpld reset altbank: reset to alternate bank\n"
+ "cpld reset sd: reset to boot from SD card\n"
+#ifdef DEBUG
+ "cpld dump - display the CPLD registers\n"
+#endif
+);
diff --git a/board/freescale/ls1046ardb/cpld.h
b/board/freescale/ls1046ardb/cpld.h
new file mode 100644
index 0000000..458da7e
--- /dev/null
+++ b/board/freescale/ls1046ardb/cpld.h
@@ -0,0 +1,49 @@
+/*
+ * Copyright 2016 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CPLD_H__
+#define __CPLD_H__
+
+/*
+ * CPLD register set of LS1046ARDB board-specific.
+ * CPLD Revision: V2.1
+ */
+struct cpld_data {
+ u8 cpld_ver; /* 0x0 - CPLD Major Revision Register */
+ u8 cpld_ver_sub; /* 0x1 - CPLD Minor Revision Register */
+ u8 pcba_ver; /* 0x2 - PCBA Revision Register */
+ u8 system_rst; /* 0x3 - system reset register */
+ u8 soft_mux_on; /* 0x4 - Switch Control Enable Register */
+ u8 cfg_rcw_src1; /* 0x5 - RCW Source Location POR Regsiter 1 */
+ u8 cfg_rcw_src2; /* 0x6 - RCW Source Location POR Regsiter 2 */
+ u8 vbank; /* 0x7 - QSPI Flash Bank Setting Register */
+ u8 sysclk_sel; /* 0x8 - System clock POR Register */
+ u8 uart_sel; /* 0x9 - UART1 Connection Control Register */
+ u8 sd1refclk_sel; /* 0xA - */
+ u8 rgmii_1588_sel; /* 0xB - */
+ u8 reg_1588_clk_sel; /* 0xC - */
+ u8 status_led; /* 0xD - */
+ u8 global_rst; /* 0xE - */
+ u8 sd_emmc; /* 0xF - SD/EMMC Interface Control Regsiter */
+ u8 vdd_en; /* 0x10 - VDD Voltage Control Enable Register */
+ u8 vdd_sel; /* 0x11 - VDD Voltage Control Register */
+};
+
+u8 cpld_read(unsigned int reg);
+void cpld_write(unsigned int reg, u8 value);
+void cpld_rev_bit(unsigned char *value);
+
+#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
+#define CPLD_WRITE(reg, value) \
+ cpld_write(offsetof(struct cpld_data, reg), value)
+
+/* CPLD on IFC */
+#define CPLD_SW_MUX_BANK_SEL 0x40
+#define CPLD_BANK_SEL_MASK 0x07
+#define CPLD_BANK_SEL_ALTBANK 0x04
+#define CPLD_CFG_RCW_SRC_QSPI 0x044
+#define CPLD_CFG_RCW_SRC_SD 0x040
+#endif
diff --git a/board/freescale/ls1046ardb/ddr.c b/board/freescale/ls1046ardb/ddr.c
new file mode 100644
index 0000000..a9b7dbd
--- /dev/null
+++ b/board/freescale/ls1046ardb/ddr.c
@@ -0,0 +1,140 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include "ddr.h"
+#ifdef CONFIG_FSL_DEEP_SLEEP
+#include <fsl_sleep.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ pbsp = udimms[0];
+
+ /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found for %lu MT/s\n",
+ ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+
+ popts->data_bus_width = 0; /* 64-bit data bus */
+ popts->otf_burst_chop_en = 0;
+ popts->burst_length = DDR_BL8;
+ popts->bstopre = 0; /* enable auto precharge */
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+ DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
+ return fsl_ddr_sdram_size();
+#else
+ puts("Initializing DDR....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+#endif
+
+ erratum_a008850_post();
+
+ return dram_size;
+}
+
+void dram_init_banksize(void)
+{
+ /*
+ * gd->arch.secure_ram tracks the location of secure memory.
+ * It was set as if the memory starts from 0.
+ * The address needs to add the offset of its bank.
+ */
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
+ gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
+ gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
+ gd->bd->bi_dram[1].size = gd->ram_size -
+ CONFIG_SYS_DDR_BLOCK1_SIZE;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+ gd->arch.secure_ram = gd->bd->bi_dram[1].start +
+ gd->arch.secure_ram -
+ CONFIG_SYS_DDR_BLOCK1_SIZE;
+ gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
+ } else {
+ gd->bd->bi_dram[0].size = gd->ram_size;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+ gd->arch.secure_ram = gd->bd->bi_dram[0].start +
+ gd->arch.secure_ram;
+ gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
+ }
+}
diff --git a/board/freescale/ls1046ardb/ddr.h b/board/freescale/ls1046ardb/ddr.h
new file mode 100644
index 0000000..9e440f6
--- /dev/null
+++ b/board/freescale/ls1046ardb/ddr.h
@@ -0,0 +1,44 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+
+void erratum_a008850_post(void);
+
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+ {2, 1350, 0, 8, 6, 0x0708090B, 0x0C0D0E09,},
+ {2, 1666, 0, 8, 7, 0x08090A0C, 0x0D0F100B,},
+ {2, 1900, 0, 8, 7, 0x09090B0D, 0x0E10120B,},
+ {2, 2300, 0, 8, 9, 0x0A0B0C10, 0x1213140E,},
+ {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+
+#endif
diff --git a/board/freescale/ls1046ardb/eth.c b/board/freescale/ls1046ardb/eth.c
new file mode 100644
index 0000000..ac8bbec
--- /dev/null
+++ b/board/freescale/ls1046ardb/eth.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <netdev.h>
+#include <fm_eth.h>
+#include <fsl_dtsec.h>
+#include <fsl_mdio.h>
+#include <malloc.h>
+
+#include "../common/fman.h"
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_FMAN_ENET
+ int i;
+ struct memac_mdio_info dtsec_mdio_info;
+ struct memac_mdio_info tgec_mdio_info;
+ struct mii_dev *dev;
+ u32 srds_s1;
+ struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
+ srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ dtsec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the 1G MDIO bus */
+ fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+ tgec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+ tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+ /* Register the 10G MDIO bus */
+ fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+ /* Set the two on-board RGMII PHY address */
+ fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR);
+
+ /* Set the two on-board SGMII PHY address */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_PHY1_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_PHY2_ADDR);
+
+ /* Set the on-board AQ PHY address */
+ fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
+
+ switch (srds_s1) {
+ case 0x1133:
+ break;
+ default:
+ printf("Invalid SerDes protocol 0x%x for LS1046ARDB\n",
+ srds_s1);
+ break;
+ }
+
+ dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++)
+ fm_info_set_mdio(i, dev);
+
+ /* XFI on lane A, MAC 9 */
+ dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+ fm_info_set_mdio(FM1_10GEC1, dev);
+
+ cpu_eth_init(bis);
+#endif
+
+ return pci_eth_init(bis);
+}
diff --git a/board/freescale/ls1046ardb/ls1046ardb.c
b/board/freescale/ls1046ardb/ls1046ardb.c
new file mode 100644
index 0000000..585c807
--- /dev/null
+++ b/board/freescale/ls1046ardb/ls1046ardb.c
@@ -0,0 +1,136 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <fdt_support.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/ppa.h>
+#include <asm/arch/soc.h>
+#include <hwconfig.h>
+#include <ahci.h>
+#include <mmc.h>
+#include <scsi.h>
+#include <fm_eth.h>
+#include <fsl_csu.h>
+#include <fsl_esdhc.h>
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ static const char *freq[2] = {"100.00MHZ", "156.25MHZ"};
+ u8 cfg_rcw_src1, cfg_rcw_src2;
+ u16 cfg_rcw_src;
+ u8 sd1refclk_sel;
+
+ puts("Board: LS1046ARDB, boot from ");
+
+ cfg_rcw_src1 = CPLD_READ(cfg_rcw_src1);
+ cfg_rcw_src2 = CPLD_READ(cfg_rcw_src2);
+ cpld_rev_bit(&cfg_rcw_src1);
+ cfg_rcw_src = cfg_rcw_src1;
+ cfg_rcw_src = (cfg_rcw_src << 1) | cfg_rcw_src2;
+
+ if (cfg_rcw_src == 0x44)
+ printf("QSPI vBank %d\n", CPLD_READ(vbank));
+ else if (cfg_rcw_src == 0x40)
+ puts("SD\n");
+ else
+ puts("Invalid setting of SW5\n");
+
+ printf("CPLD: V%x.%x\nPCBA: V%x.0\n", CPLD_READ(cpld_ver),
+ CPLD_READ(cpld_ver_sub), CPLD_READ(pcba_ver));
+
+ puts("SERDES Reference Clocks:\n");
+ sd1refclk_sel = CPLD_READ(sd1refclk_sel);
+ printf("SD1_CLK1 = %s, SD1_CLK2 = %s\n", freq[sd1refclk_sel], freq[0]);
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = initdram(0);
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ fsl_lsch2_early_init_f();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+
+#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
+ enable_layerscape_ns_access();
+#endif
+
+#ifdef CONFIG_FSL_LS_PPA
+ ppa_init();
+#endif
+
+ /* invert AQR105 IRQ pins polarity */
+ out_be32(&scfg->intpcr, AQR105_IRQ_MASK);
+
+ return 0;
+}
+
+void config_board_mux(void)
+{
+#ifdef CONFIG_HAS_FSL_XHCI_USB
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+ u32 usb_pwrfault;
+
+ /* USB3 is not used, configure mux to IIC4_SCL/IIC4_SDA */
+ out_be32(&scfg->rcwpmuxcr0, 0x3300);
+ out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1);
+ usb_pwrfault = (SCFG_USBPWRFAULT_DEDICATED <<
+ SCFG_USBPWRFAULT_USB3_SHIFT) |
+ (SCFG_USBPWRFAULT_DEDICATED <<
+ SCFG_USBPWRFAULT_USB2_SHIFT) |
+ (SCFG_USBPWRFAULT_SHARED <<
+ SCFG_USBPWRFAULT_USB1_SHIFT);
+ out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
+#endif
+}
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+ config_board_mux();
+ return 0;
+}
+#endif
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ u64 base[CONFIG_NR_DRAM_BANKS];
+ u64 size[CONFIG_NR_DRAM_BANKS];
+
+ /* fixup DT for the two DDR banks */
+ base[0] = gd->bd->bi_dram[0].start;
+ size[0] = gd->bd->bi_dram[0].size;
+ base[1] = gd->bd->bi_dram[1].start;
+ size[1] = gd->bd->bi_dram[1].size;
+
+ fdt_fixup_memory_banks(blob, base, size, 2);
+ ft_cpu_setup(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+#endif
+
+ return 0;
+}
diff --git a/board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
b/board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
new file mode 100644
index 0000000..5478217
--- /dev/null
+++ b/board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
@@ -0,0 +1,22 @@
+#Configure Scratch register
+09570600 00000000
+09570604 10000000
+#Disable CCI barrier tranaction
+09570178 0000e010
+09180000 00000008
+#USB PHY frequency sel
+09570418 0000009e
+0957041c 0000009e
+09570420 0000009e
+#Serdes SATA
+09eb1300 80104e20
+09eb08dc 00502880
+#PEX gen3 link
+09570158 00000300
+89400890 01048000
+89500890 01048000
+89600890 01048000
+#Alt base register
+09570158 00001000
+#flush PBI data
+096100c0 000fffff
diff --git a/board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
b/board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
new file mode 100644
index 0000000..6a5076e
--- /dev/null
+++ b/board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+# RCW
+0c150010 0e000000 00000000 00000000
+11335559 40000012 60040000 c1000000
+00000000 00000000 00000000 00238800
+20124000 00003000 00000096 00000001
diff --git a/board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
b/board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
new file mode 100644
index 0000000..d5265b8
--- /dev/null
+++ b/board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+# RCW
+0c150010 0e000000 00000000 00000000
+11335559 40005012 60040000 c1000000
+00000000 00000000 00000000 00238800
+20124000 00003101 00000096 00000001
diff --git a/configs/ls1046ardb_emmc_defconfig
b/configs/ls1046ardb_emmc_defconfig
new file mode 100644
index 0000000..1f0f3a4
--- /dev/null
+++ b/configs/ls1046ardb_emmc_defconfig
@@ -0,0 +1,26 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1046ARDB=y
+CONFIG_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-rdb"
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SYS_FSL_DDR4,CONFIG_EMMC_BOOT"
+CONFIG_SD_BOOT=y
+CONFIG_BOOTDELAY=10
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_SYS_NS16550=y
diff --git a/configs/ls1046ardb_qspi_defconfig
b/configs/ls1046ardb_qspi_defconfig
new file mode 100644
index 0000000..4b9d050
--- /dev/null
+++ b/configs/ls1046ardb_qspi_defconfig
@@ -0,0 +1,25 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1046ARDB=y
+CONFIG_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-rdb"
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_QSPI_BOOT=y
+CONFIG_BOOTDELAY=10
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_SYS_NS16550=y
diff --git a/configs/ls1046ardb_sdcard_defconfig
b/configs/ls1046ardb_sdcard_defconfig
new file mode 100644
index 0000000..f489e91
--- /dev/null
+++ b/configs/ls1046ardb_sdcard_defconfig
@@ -0,0 +1,26 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1046ARDB=y
+CONFIG_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-rdb"
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SYS_FSL_DDR4"
+CONFIG_SD_BOOT=y
+CONFIG_BOOTDELAY=10
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_SYS_NS16550=y
diff --git a/include/configs/ls1046a_common.h b/include/configs/ls1046a_common.h
new file mode 100644
index 0000000..9ee29b4
--- /dev/null
+++ b/include/configs/ls1046a_common.h
@@ -0,0 +1,175 @@
+/*
+ * Copyright 2016 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1046A_COMMON_H
+#define __LS1046A_COMMON_H
+
+#define CONFIG_REMAKE_ELF
+#define CONFIG_FSL_LAYERSCAPE
+#define CONFIG_FSL_LSCH2
+#define CONFIG_LS1046A
+#define CONFIG_MP
+#define CONFIG_SYS_FSL_CLK
+#define CONFIG_GICV2
+
+#include <asm/arch/config.h>
+#ifdef CONFIG_SYS_FSL_SRDS_1
+#define CONFIG_SYS_HAS_SERDES
+#endif
+
+/* Link Definitions */
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE +
0xfff0)
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
+#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL
+
+#define CPU_RELEASE_ADDR secondary_boot_func
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY 25000000 /* 25MHz */
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/* SD boot SPL */
+#ifdef CONFIG_SD_BOOT
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_WATCHDOG_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x110
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x500
+#define CONFIG_SPL_TEXT_BASE 0x10000000
+#define CONFIG_SPL_MAX_SIZE 0x1f000 /* 124 KiB */
+#define CONFIG_SPL_STACK 0x10020000
+#define CONFIG_SPL_PAD_TO 0x21000 /* 132 KiB */
+#define CONFIG_SPL_BSS_START_ADDR 0x8f000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
+ CONFIG_SPL_BSS_MAX_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
+#define CONFIG_SYS_MONITOR_LEN 0xa0000
+#endif
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_MXC_I2C2
+#define CONFIG_SYS_I2C_MXC_I2C3
+#define CONFIG_SYS_I2C_MXC_I2C4
+
+/* Command line configuration */
+#define CONFIG_CMD_ENV
+
+/* MMC */
+#define CONFIG_MMC
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+#endif
+
+#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
+
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+
+/* FMan ucode */
+#define CONFIG_SYS_DPAA_FMAN
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_FM_MURAM_SIZE 0x60000
+
+#ifdef CONFIG_SD_BOOT
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image
is
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
+#else
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_FMAN_FW_ADDR 0x40300000
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 1000000
+#define CONFIG_ENV_SPI_MODE 0x03
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
+#define CONFIG_ARCH_EARLY_INIT_R
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_HWCONFIG
+#define HWCONFIG_BUFFER_SIZE 128
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "loadaddr=0x80100000\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "kernel_start=0x1000000\0" \
+ "kernel_load=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "console=ttyS0,115200\0" \
+ MTDPARTS_DEFAULT "\0"
+
+#define CONFIG_BOOTARGS "console=ttyS0,115200
root=/dev/ram0 " \
+ "earlycon=uart8250,mmio,0x21c0500 " \
+ MTDPARTS_DEFAULT
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_MAXARGS 64 /* max command args */
+
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+/* Hash command with SHA acceleration supported in hardware */
+#ifdef CONFIG_FSL_CAAM
+#define CONFIG_CMD_HASH
+#define CONFIG_SHA_HW_ACCEL
+#endif
+
+#endif /* __LS1046A_COMMON_H */
diff --git a/include/configs/ls1046ardb.h b/include/configs/ls1046ardb.h
new file mode 100644
index 0000000..693cc8d
--- /dev/null
+++ b/include/configs/ls1046ardb.h
@@ -0,0 +1,240 @@
+/*
+ * Copyright 2016 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1046ARDB_H__
+#define __LS1046ARDB_H__
+
+#include "ls1046a_common.h"
+
+#if defined(CONFIG_FSL_LS_PPA)
+#define CONFIG_ARMV8_PSCI
+#define CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT
+#define CONFIG_SYS_LS_PPA_DRAM_BLOCK_MIN_SIZE (1UL * 1024 * 1024)
+
+#define CONFIG_SYS_LS_PPA_FW_IN_XIP
+#ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
+#define CONFIG_SYS_LS_PPA_FW_ADDR 0x40500000
+#endif
+#endif
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#ifdef CONFIG_SD_BOOT
+#define CONFIG_SYS_TEXT_BASE 0x82000000
+#else
+#define CONFIG_SYS_TEXT_BASE 0x40100000
+#endif
+
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 100000000
+
+#define CONFIG_LAYERSCAPE_NS_ACCESS
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+/* Physical Memory Map */
+#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+#define CONFIG_NR_DRAM_BANKS 2
+
+#define CONFIG_DDR_SPD
+#define SPD_EEPROM_ADDRESS 0x51
+#define CONFIG_SYS_SPD_BUS_NUM 0
+
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
+#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
+#endif
+
+#ifdef CONFIG_SD_BOOT
+#ifdef CONFIG_EMMC_BOOT
+#define CONFIG_SYS_FSL_PBL_RCW \
+ board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
+#else
+#define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
+#endif
+#endif
+
+/* No NOR flash */
+#define CONFIG_SYS_NO_FLASH
+
+/* IFC */
+#define CONFIG_FSL_IFC
+
+/*
+ * NAND Flash Definitions
+ */
+#define CONFIG_NAND_FSL_IFC
+
+#define CONFIG_SYS_NAND_BASE 0x7e800000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_NAND \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_8 /* 8-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \
+ | CSOR_NAND_PGS_4K /* Page Size = 4K */ \
+ | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
+ | CSOR_NAND_PB(64)) /* 64 Pages Per Block */
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x7) | \
+ FTIM0_NAND_TWH(0xa))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0xe) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \
+ FTIM2_NAND_TREH(0xa) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/*
+ * CPLD
+ */
+#define CONFIG_SYS_CPLD_BASE 0x7fb00000
+#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE
+
+#define CONFIG_SYS_CPLD_CSPR_EXT (0x0)
+#define CONFIG_SYS_CPLD_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
+ CSPR_PORT_SIZE_8 | \
+ CSPR_MSEL_GPCM | \
+ CSPR_V)
+#define CONFIG_SYS_CPLD_AMASK IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_CPLD_CSOR CSOR_NOR_ADM_SHIFT(16)
+
+/* CPLD Timing parameters for IFC GPCM */
+#define CONFIG_SYS_CPLD_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CPLD_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CPLD_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
+ FTIM2_GPCM_TCH(0xf) | \
+ FTIM2_GPCM_TWP(0x3E))
+#define CONFIG_SYS_CPLD_FTIM3 0x0
+
+/* IFC Timing Params */
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_CPLD_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_CPLD_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_CPLD_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_CPLD_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_CPLD_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_CPLD_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_CPLD_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_CPLD_FTIM3
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+#define I2C_RETIMER_ADDR 0x18
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_SD_BOOT)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_OFFSET (1024 * 1024)
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x200000 /* 2MB */
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256KB */
+#endif
+
+/* FMan */
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_AQUANTIA
+#define AQR105_IRQ_MASK 0x80000000
+
+#define RGMII_PHY1_ADDR 0x1
+#define RGMII_PHY2_ADDR 0x2
+
+#define SGMII_PHY1_ADDR 0x3
+#define SGMII_PHY2_ADDR 0x4
+
+#define FM1_10GEC1_PHY_ADDR 0x0
+
+#define CONFIG_ETHPRIME "FM1@DTSEC3"
+#endif
+
+/* QSPI device */
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE (1 << 26)
+#define FSL_QSPI_FLASH_NUM 2
+#define CONFIG_SPI_FLASH_BAR
+#endif
+
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SCSI
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SATA AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_BOOTCOMMAND "sf probe 0:0;sf read $kernel_load" \
+ "$kernel_start $kernel_size;" \
+ "bootm $kernel_load"
+
+#define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:1m(rcw)," \
+ "15m(u-boot),48m(kernel.itb);" \
+ "7e800000.flash:16m(nand_uboot)," \
+ "48m(nand_kernel),448m(nand_free)"
+
+#endif /* __LS1046ARDB_H__ */
--
2.1.0.27.g96db324
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
