Hi,

On 19 September 2016 at 00:17, Keerthy <j-keer...@ti.com> wrote:
> Add u8 i2c read/write hooks.
>
> Signed-off-by: Keerthy <j-keer...@ti.com>
> ---
>  drivers/i2c/i2c-uclass.c | 10 ++++++++++
>  include/i2c.h            | 24 ++++++++++++++++++++++++
>  2 files changed, 34 insertions(+)
>
> diff --git a/drivers/i2c/i2c-uclass.c b/drivers/i2c/i2c-uclass.c
> index dbd3789..6ce5d9a 100644
> --- a/drivers/i2c/i2c-uclass.c
> +++ b/drivers/i2c/i2c-uclass.c
> @@ -231,6 +231,16 @@ int dm_i2c_reg_write(struct udevice *dev, uint offset, 
> uint value)
>         return dm_i2c_write(dev, offset, &val, 1);
>  }
>
> +int dm_i2c_u8_read(struct udevice *dev, uint offset, u8 *val)
> +{
> +       return dm_i2c_read(dev, offset, val, 1);
> +}
> +
> +int dm_i2c_u8_write(struct udevice *dev, uint offset, u8 *val)
> +{
> +       return dm_i2c_write(dev, offset, val, 1);
> +}

These look almost the same as dm_i2c_reg_read/write(), but IMO those
are easier to use since they don't require a pointer to be passed. How
do you intend to use these two new functions?

> +
>  /**
>   * i2c_probe_chip() - probe for a chip on a bus
>   *
> diff --git a/include/i2c.h b/include/i2c.h
> index d500445..c3059ad 100644
> --- a/include/i2c.h
> +++ b/include/i2c.h
> @@ -191,6 +191,30 @@ int dm_i2c_reg_read(struct udevice *dev, uint offset);
>  int dm_i2c_reg_write(struct udevice *dev, uint offset, unsigned int val);
>
>  /**
> + * dm_i2c_u8_read() - Read a byte value from an I2C register
> + *
> + * This reads a single value from the given address in an I2C chip
> + *
> + * @dev:        Device to use for transfer
> + * @addr:       Address to read from
> + * @val:       Value read is stored in val
> + * @return 0 for success, -ve on error
> + */
> +int dm_i2c_u8_read(struct udevice *dev, uint offset, u8 *val);
> +
> +/**
> + * dm_i2c_u8_write() - Write a byte value to an I2C register
> + *
> + * This writes a single value to the given address in an I2C chip
> + *
> + * @dev:        Device to use for transfer
> + * @addr:       Address to write to
> + * @val:        Value to write
> + * @return 0 on success, -ve on error
> + */
> +int dm_i2c_u8_write(struct udevice *dev, uint offset, u8 *val);
> +
> +/**
>   * dm_i2c_xfer() - Transfer messages over I2C
>   *
>   * This transfers a raw message. It is best to use dm_i2c_reg_read/write()
> --
> 1.9.1

Regards,
Simon
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to