From: Dmitry Lifshitz <lifsh...@compulab.co.il>

Add MAC support.

Use PHY, connected to RGMII1 as a default Eth adapter,
by appropriate setting of 'cpsw_data.active_slave'.

'cpsw_phy' env variable can override this setting.

Set the MAC addresses in the U-Boot environment.
The addresses are retrieved from the on-board EEPROM or from the SOC's
MAC fuses.

Set the following PHYs RGMII clock delays:
- Enable RX delay
- Disable TX delay

Signed-off-by: Dmitry Lifshitz <lifsh...@compulab.co.il>
[uri.mashi...@compulab.co.il: add RGMII clock delays]
Signed-off-by: Uri Mashiach <uri.mashi...@compulab.co.il>
Acked-by: Igor Grinberg <grinb...@compulab.co.il>
---
 board/compulab/cl-som-am57x/Makefile |   2 +
 board/compulab/cl-som-am57x/eth.c    | 199 +++++++++++++++++++++++++++++++++++
 board/compulab/cl-som-am57x/mux.c    |  23 ++++
 include/configs/cl-som-am57x.h       |  17 +++
 4 files changed, 241 insertions(+)
 create mode 100644 board/compulab/cl-som-am57x/eth.c

diff --git a/board/compulab/cl-som-am57x/Makefile 
b/board/compulab/cl-som-am57x/Makefile
index 0c59781..566366b 100644
--- a/board/compulab/cl-som-am57x/Makefile
+++ b/board/compulab/cl-som-am57x/Makefile
@@ -13,3 +13,5 @@ obj-y += spl.o mux.o
 else
 obj-y  += cl-som-am57x.o mux.o
 endif
+
+obj-$(CONFIG_DRIVER_TI_CPSW)   += eth.o
diff --git a/board/compulab/cl-som-am57x/eth.c 
b/board/compulab/cl-som-am57x/eth.c
new file mode 100644
index 0000000..ce91b7f
--- /dev/null
+++ b/board/compulab/cl-som-am57x/eth.c
@@ -0,0 +1,199 @@
+/*
+ * Ethernet specific code for CompuLab CL-SOM-AM57x module
+ *
+ * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/
+ *
+ * Author: Uri Mashiach <uri.mashi...@compulab.co.il>
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <cpsw.h>
+#include <miiphy.h>
+#include <asm/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include "../common/eeprom.h"
+
+static void cpsw_control(int enabled)
+{
+       /* VTP can be added here */
+}
+
+static struct cpsw_slave_data cl_som_am57x_cpsw_slaves[] = {
+       {
+               .slave_reg_ofs  = 0x208,
+               .sliver_reg_ofs = 0xd80,
+               .phy_addr       = 0,
+               .phy_if         = PHY_INTERFACE_MODE_RMII,
+       },
+       {
+               .slave_reg_ofs  = 0x308,
+               .sliver_reg_ofs = 0xdc0,
+               .phy_addr       = 1,
+               .phy_if         = PHY_INTERFACE_MODE_RMII,
+
+       },
+};
+
+static struct cpsw_platform_data cl_som_am57_cpsw_data = {
+       .mdio_base              = CPSW_MDIO_BASE,
+       .cpsw_base              = CPSW_BASE,
+       .mdio_div               = 0xff,
+       .channels               = 8,
+       .cpdma_reg_ofs          = 0x800,
+       .slaves                 = 2,
+       .slave_data             = cl_som_am57x_cpsw_slaves,
+       .ale_reg_ofs            = 0xd00,
+       .ale_entries            = 1024,
+       .host_port_reg_ofs      = 0x108,
+       .hw_stats_reg_ofs       = 0x900,
+       .bd_ram_ofs             = 0x2000,
+       .mac_control            = (1 << 5),
+       .control                = cpsw_control,
+       .host_port_num          = 0,
+       .version                = CPSW_CTRL_VERSION_2,
+};
+
+/*
+ * cl_som_am57x_efuse_read_mac_addr() - read Ethernet port MAC address.
+ *       The information is retrieved from the SOC's registers.
+ * @buff: read buffer.
+ * @port_num: port number.
+ */
+static void cl_som_am57x_efuse_read_mac_addr(uchar *buff, uint port_num)
+{
+       uint32_t mac_hi, mac_lo;
+
+       if (port_num) {
+               mac_lo = readl((*ctrl)->control_core_mac_id_1_lo);
+               mac_hi = readl((*ctrl)->control_core_mac_id_1_hi);
+       } else {
+               mac_lo = readl((*ctrl)->control_core_mac_id_0_lo);
+               mac_hi = readl((*ctrl)->control_core_mac_id_0_hi);
+       }
+
+       buff[0] = (mac_hi & 0xFF0000) >> 16;
+       buff[1] = (mac_hi & 0xFF00) >> 8;
+       buff[2] = mac_hi & 0xFF;
+       buff[3] = (mac_lo & 0xFF0000) >> 16;
+       buff[4] = (mac_lo & 0xFF00) >> 8;
+       buff[5] = mac_lo & 0xFF;
+}
+
+/*
+ * cl_som_am57x_handle_mac_address() - set MAC address in the U-Boot
+ *     environment.
+ *      The address is retrieved retrieved from an EEPROM field or from the
+ *     SOC's registers.
+ * @env_name: U-Boot environment name.
+ * @field_name: EEPROM field name.
+ * @port_num: SOC's port number.
+ */
+static int cl_som_am57x_handle_mac_address(char *env_name, uint port_num)
+{
+       int ret;
+       uint8_t enetaddr[6];
+
+       ret = eth_getenv_enetaddr(env_name, enetaddr);
+       if (ret)
+               return 0;
+
+       ret = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
+
+       if (ret || !is_valid_ethaddr(enetaddr))
+               cl_som_am57x_efuse_read_mac_addr(enetaddr, port_num);
+
+       if (!is_valid_ethaddr(enetaddr))
+               return -1;
+
+       ret = eth_setenv_enetaddr(env_name, enetaddr);
+       if (ret)
+               printf("cl-som-am57x: Failed to set Eth port %d MAC address\n",
+                      port_num);
+
+       return ret;
+}
+
+#define CL_SOM_AM57X_PHY_ADDR2                 0x01
+#define AR8033_PHY_DEBUG_ADDR_REG              0x1d
+#define AR8033_PHY_DEBUG_DATA_REG              0x1e
+#define AR8033_DEBUG_RGMII_RX_CLK_DLY_REG      0x00
+#define AR8033_DEBUG_RGMII_TX_CLK_DLY_REG      0x05
+#define AR8033_DEBUG_RGMII_RX_CLK_DLY_MASK     (1 << 15)
+#define AR8033_DEBUG_RGMII_TX_CLK_DLY_MASK     (1 << 8)
+
+/*
+ * cl_som_am57x_rgmii_clk_delay() - Set RGMII clock delay.
+ *     Enable RX delay, disable TX delay.
+ */
+static void cl_som_am57x_rgmii_clk_delay(void)
+{
+       uint16_t mii_reg_val;
+       const char *devname;
+
+       devname = miiphy_get_current_dev();
+       /* PHY 2 */
+       miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_ADDR_REG,
+                    AR8033_DEBUG_RGMII_RX_CLK_DLY_REG);
+       miiphy_read(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG,
+                   &mii_reg_val);
+       mii_reg_val |= AR8033_DEBUG_RGMII_RX_CLK_DLY_MASK;
+       miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG,
+                    mii_reg_val);
+
+       miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_ADDR_REG,
+                    AR8033_DEBUG_RGMII_TX_CLK_DLY_REG);
+       miiphy_read(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG,
+                   &mii_reg_val);
+       mii_reg_val &= ~AR8033_DEBUG_RGMII_TX_CLK_DLY_MASK;
+       miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG,
+                    mii_reg_val);
+}
+
+#define CL_SOM_AM57X_GPIO_PHY1_RST 92 /* GPIO3_28 */
+#define CL_SOM_AM57X_RGMII_PORT1 1
+
+int board_eth_init(bd_t *bis)
+{
+       int ret;
+       uint32_t ctrl_val;
+       char *cpsw_phy_envval;
+       int cpsw_act_phy = 1;
+
+       /* SB-SOM-AM57x primary Eth (P21) is routed to RGMII1 */
+       ret = cl_som_am57x_handle_mac_address("ethaddr",
+                                             CL_SOM_AM57X_RGMII_PORT1);
+
+       if (ret)
+               return -1;
+
+       /* Select RGMII for GMII1_SEL */
+       ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33);
+       ctrl_val |= 0x22;
+       writel(ctrl_val, (*ctrl)->control_core_control_io1);
+       mdelay(10);
+
+       gpio_request(CL_SOM_AM57X_GPIO_PHY1_RST, "phy1_rst");
+       gpio_direction_output(CL_SOM_AM57X_GPIO_PHY1_RST, 0);
+       mdelay(20);
+
+       gpio_set_value(CL_SOM_AM57X_GPIO_PHY1_RST, 1);
+       mdelay(20);
+
+       cpsw_phy_envval = getenv("cpsw_phy");
+       if (cpsw_phy_envval != NULL)
+               cpsw_act_phy = simple_strtoul(cpsw_phy_envval, NULL, 0);
+
+       cl_som_am57_cpsw_data.active_slave = cpsw_act_phy;
+
+       ret = cpsw_register(&cl_som_am57_cpsw_data);
+       if (ret < 0)
+               printf("Error %d registering CPSW switch\n", ret);
+
+       /* Set RGMII clock delay */
+       cl_som_am57x_rgmii_clk_delay();
+
+       return ret;
+}
+
diff --git a/board/compulab/cl-som-am57x/mux.c 
b/board/compulab/cl-som-am57x/mux.c
index 625cbc1..5b71975 100644
--- a/board/compulab/cl-som-am57x/mux.c
+++ b/board/compulab/cl-som-am57x/mux.c
@@ -83,6 +83,28 @@ static const struct pad_conf_entry 
cl_som_am57x_padconf_usb[] = {
        {USB1_DRVVBUS, (M0 | FSC) }, /* USB1_DRVVBUS.USB1_DRVVBUS */
 };
 
+/* Ethernet */
+static const struct pad_conf_entry cl_som_am57x_padconf_ethernet[] = {
+       /* MDIO bus */
+       {VIN2A_D10,  (PDIS | PTU  |       M3) }, /* VIN2A_D10.MDIO_MCLK  */
+       {VIN2A_D11,  (IEN  | PDIS | PTU | M3) }, /* VIN2A_D11.MDIO_D  */
+       /* EMAC Slave 1 at addr 0x1 - Default interface */
+       {VIN2A_D12,  (IDIS | PEN  |       M3) }, /* VIN2A_D12.RGMII1_TXC */
+       {VIN2A_D13,  (IDIS | PEN  |       M3) }, /* VIN2A_D13.RGMII1_TXCTL */
+       {VIN2A_D14,  (IDIS | PEN  |       M3) }, /* VIN2A_D14.RGMII1_TXD3 */
+       {VIN2A_D15,  (IDIS | PEN  |       M3) }, /* VIN2A_D15.RGMII1_TXD2 */
+       {VIN2A_D16,  (IDIS | PEN  |       M3) }, /* VIN2A_D16.RGMII1_TXD1 */
+       {VIN2A_D17,  (IDIS | PEN  |       M3) }, /* VIN2A_D17.RGMII1_TXD0 */
+       {VIN2A_D18,  (IEN  | PDIS | PTD | M3) }, /* VIN2A_D18.RGMII1_RXC */
+       {VIN2A_D19,  (IEN  | PDIS | PTD | M3) }, /* VIN2A_D19.RGMII1_RXCTL */
+       {VIN2A_D20,  (IEN  | PDIS | PTD | M3) }, /* VIN2A_D20.RGMII1_RXD3 */
+       {VIN2A_D21,  (IEN  | PDIS | PTD | M3) }, /* VIN2A_D21.RGMII1_RXD2 */
+       {VIN2A_D22,  (IEN  | PDIS | PTD | M3) }, /* VIN2A_D22.RGMII1_RXD1 */
+       {VIN2A_D23,  (IEN  | PDIS | PTD | M3) }, /* VIN2A_D23.RGMII1_RXD0 */
+       /* Eth PHY1 reset GPIOs*/
+       {VIN1B_CLK1, (IDIS | PDIS | PTD | M14)}, /* VIN1B_CLK1.GPIO2_31 */
+};
+
 #define SET_MUX(mux_array) do_set_mux32((*ctrl)->control_padconf_core_base, \
                                        mux_array, ARRAY_SIZE(mux_array))
 
@@ -97,4 +119,5 @@ void set_muxconf_regs(void)
        SET_MUX(cl_som_am57x_padconf_i2c_gpio);
        SET_MUX(cl_som_am57x_padconf_emmc);
        SET_MUX(cl_som_am57x_padconf_usb);
+       SET_MUX(cl_som_am57x_padconf_ethernet);
 }
diff --git a/include/configs/cl-som-am57x.h b/include/configs/cl-som-am57x.h
index 65e506a..a22c3e6 100644
--- a/include/configs/cl-som-am57x.h
+++ b/include/configs/cl-som-am57x.h
@@ -121,6 +121,23 @@
 #define CONFIG_USB_ETHER_ASIX
 #define CONFIG_USB_ETHER_MCS7830
 
+/* CPSW Ethernet */
+#define CONFIG_DRIVER_TI_CPSW
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_PHY_GIGE
+#define CONFIG_PHY_ATHEROS
+#define CONFIG_PHYLIB
+#define CONFIG_SYS_RX_ETH_BUFFER       64
+#define PHY_ANEG_TIMEOUT               8000
+
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_NET_RETRY_COUNT         10
+
 #endif /* !CONFIG_SPL_BUILD */
 
 #endif /* __CONFIG_CL_SOM_AM57X_H */
-- 
2.7.4

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to