Hi Nobuhiro, On Thu, Nov 30, 2017 at 5:08 PM, Nobuhiro Iwamatsu <iwama...@nigauri.org> wrote: > This fixes the chord style checked by checkpatch.pl. > Details of change details are as follows: > > - Fix typo > Change from alligned to aligned. > - Remove whitespace before ',' > - Add spaces preferred around that '|' > - Fix missing a blank line after declarations > - Remove space after a cast declaration > - Fix format of block comments > - Add a blank line after function/struct/union/enum declarations > > Signed-off-by: Nobuhiro Iwamatsu <iwama...@nigauri.org> > --- > drivers/net/sh_eth.c | 29 ++++++++++++++++++----------- > 1 file changed, 18 insertions(+), 11 deletions(-) > > diff --git a/drivers/net/sh_eth.c b/drivers/net/sh_eth.c > index 970d730e56..5c6278069c 100644 > --- a/drivers/net/sh_eth.c > +++ b/drivers/net/sh_eth.c > @@ -67,7 +67,7 @@ int sh_eth_send(struct eth_device *dev, void *packet, int > len) > > /* packet must be a 4 byte boundary */ > if ((int)packet & 3) { > - printf(SHETHER_NAME ": %s: packet not 4 byte alligned\n" > + printf(SHETHER_NAME ": %s: packet not 4 byte aligned\n" > , __func__); > ret = -EFAULT; > goto err; > @@ -222,8 +222,10 @@ static int sh_eth_tx_desc_init(struct sh_eth_dev *eth) > cur_tx_desc--; > cur_tx_desc->td0 |= TD_TDLE; > > - /* Point the controller to the tx descriptor list. Must use physical > - addresses */ > + /* > + * Point the controller to the tx descriptor list. Must use physical > + * addresses > + */ > sh_eth_write(eth, ADDR_TO_PHY(port_info->tx_desc_base), TDLAR); > #if defined(SH_ETH_TYPE_GETHER) || defined(SH_ETH_TYPE_RZ) > sh_eth_write(eth, ADDR_TO_PHY(port_info->tx_desc_base), TDFAR); > @@ -237,7 +239,7 @@ err: > > static int sh_eth_rx_desc_init(struct sh_eth_dev *eth) > { > - int port = eth->port, i , ret = 0; > + int port = eth->port, i, ret = 0; > u32 alloc_desc_size = NUM_RX_DESC * sizeof(struct rx_desc_s); > struct sh_eth_info *port_info = ð->port_info[port]; > struct rx_desc_s *cur_rx_desc; > @@ -283,7 +285,7 @@ static int sh_eth_rx_desc_init(struct sh_eth_dev *eth) > i < NUM_RX_DESC; cur_rx_desc++, rx_buf += MAX_BUF_SIZE, i++) { > cur_rx_desc->rd0 = RD_RACT; > cur_rx_desc->rd1 = MAX_BUF_SIZE << 16; > - cur_rx_desc->rd2 = (u32) ADDR_TO_PHY(rx_buf); > + cur_rx_desc->rd2 = (u32)ADDR_TO_PHY(rx_buf); > } > > /* Mark the end of the descriptors */ > @@ -465,11 +467,14 @@ static int sh_eth_config(struct sh_eth_dev *eth, bd_t > *bd) > /* Check if full duplex mode is supported by the phy */ > if (phy->duplex) { > printf("Full\n"); > - sh_eth_write(eth, val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE|ECMR_DM), > + sh_eth_write(eth, > + val | (ECMR_CHG_DM | ECMR_RE | ECMR_TE | > ECMR_DM), > ECMR); > } else { > printf("Half\n"); > - sh_eth_write(eth, val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE), ECMR); > + sh_eth_write(eth, > + val | (ECMR_CHG_DM | ECMR_RE | ECMR_TE), > + ECMR); > } > > return ret; > @@ -524,6 +529,7 @@ err: > void sh_eth_halt(struct eth_device *dev) > { > struct sh_eth_dev *eth = dev->priv; > + > sh_eth_stop(eth); > } > > @@ -532,6 +538,7 @@ int sh_eth_initialize(bd_t *bd) > int ret = 0; > struct sh_eth_dev *eth = NULL; > struct eth_device *dev = NULL; > + struct mii_dev *mdiodev; > > eth = (struct sh_eth_dev *)malloc(sizeof(struct sh_eth_dev)); > if (!eth) { > @@ -566,16 +573,15 @@ int sh_eth_initialize(bd_t *bd) > eth_register(dev); > > bb_miiphy_buses[0].priv = eth; > - int retval; > - struct mii_dev *mdiodev = mdio_alloc(); > + mdiodev = mdio_alloc(); > if (!mdiodev) > return -ENOMEM; > strncpy(mdiodev->name, dev->name, MDIO_NAME_LEN); > mdiodev->read = bb_miiphy_read; > mdiodev->write = bb_miiphy_write; > > - retval = mdio_register(mdiodev); > - if (retval < 0) > + retl = mdio_register(mdiodev);
It seems you never compiled this. The compiler tells you that it should be "ret", not "retl". > + if (ret < 0) > return retval; This should be "ret", not "retval". I'll fix these up inline. -Joe > > if (!eth_env_get_enetaddr("ethaddr", dev->enetaddr)) > @@ -670,4 +676,5 @@ struct bb_miiphy_bus bb_miiphy_buses[] = { > .delay = sh_eth_bb_delay, > } > }; > + > int bb_miiphy_buses_num = ARRAY_SIZE(bb_miiphy_buses); _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot