The timeout is set to PLL_LOCK_TIMEOUT in every call to
comphy_poll_reg. Remove this parameter from the function.

Signed-off-by: Marek Behun <marek.be...@nic.cz>
---
 drivers/phy/marvell/comphy_a3700.c | 16 +++-------------
 1 file changed, 3 insertions(+), 13 deletions(-)

diff --git a/drivers/phy/marvell/comphy_a3700.c 
b/drivers/phy/marvell/comphy_a3700.c
index 6506c134e2..d283604e1a 100644
--- a/drivers/phy/marvell/comphy_a3700.c
+++ b/drivers/phy/marvell/comphy_a3700.c
@@ -106,12 +106,11 @@ static u16 sgmii_phy_init[512] = {
  *
  * return: 1 on success, 0 on timeout
  */
-static u32 comphy_poll_reg(void *addr, u32 val, u32 mask, u32 timeout,
-                          u8 op_type)
+static u32 comphy_poll_reg(void *addr, u32 val, u32 mask, u8 op_type)
 {
-       u32 rval = 0xDEAD;
+       u32 rval = 0xDEAD, timeout;
 
-       for (; timeout > 0; timeout--) {
+       for (timeout = PLL_LOCK_TIMEOUT; timeout > 0; timeout--) {
                if (op_type == POLL_16B_REG)
                        rval = readw(addr);     /* 16 bit */
                else
@@ -215,7 +214,6 @@ static int comphy_pcie_power_up(u32 speed, u32 invert)
        ret = comphy_poll_reg(PHY_ADDR(PCIE, LANE_STAT1),       /* address */
                              rb_txdclk_pclk_en,                /* value */
                              rb_txdclk_pclk_en,                /* mask */
-                             PLL_LOCK_TIMEOUT,                 /* timeout */
                              POLL_16B_REG);                    /* 16bit */
        if (ret == 0)
                printf("Failed to lock PCIe PLL\n");
@@ -285,7 +283,6 @@ static int comphy_sata_power_up(void)
        ret = comphy_poll_reg(rh_vsreg_data,    /* address */
                              bs_pll_ready_tx,  /* value */
                              bs_pll_ready_tx,  /* mask */
-                             PLL_LOCK_TIMEOUT, /* timeout */
                              POLL_32B_REG);    /* 32bit */
        if (ret == 0)
                printf("Failed to lock SATA PLL\n");
@@ -414,7 +411,6 @@ static int comphy_usb3_power_up(u32 type, u32 speed, u32 
invert)
        ret = comphy_poll_reg(PHY_ADDR(USB3, LANE_STAT1),       /* address */
                              rb_txdclk_pclk_en,        /* value */
                              rb_txdclk_pclk_en,        /* mask */
-                             PLL_LOCK_TIMEOUT,         /* timeout */
                              POLL_16B_REG);            /* 16bit */
        if (ret == 0)
                printf("Failed to lock USB3 PLL\n");
@@ -495,7 +491,6 @@ static int comphy_usb2_power_up(u8 usb32)
        ret = comphy_poll_reg(USB2_PHY_CAL_CTRL_ADDR(usb32),
                              rb_usb2phy_pllcal_done,   /* value */
                              rb_usb2phy_pllcal_done,   /* mask */
-                             PLL_LOCK_TIMEOUT,         /* timeout */
                              POLL_32B_REG);            /* 32bit */
        if (ret == 0)
                printf("Failed to end USB2 PLL calibration\n");
@@ -504,7 +499,6 @@ static int comphy_usb2_power_up(u8 usb32)
        ret = comphy_poll_reg(USB2_PHY_CAL_CTRL_ADDR(usb32),
                              rb_usb2phy_impcal_done,   /* value */
                              rb_usb2phy_impcal_done,   /* mask */
-                             PLL_LOCK_TIMEOUT,         /* timeout */
                              POLL_32B_REG);            /* 32bit */
        if (ret == 0)
                printf("Failed to end USB2 impedance calibration\n");
@@ -513,7 +507,6 @@ static int comphy_usb2_power_up(u8 usb32)
        ret = comphy_poll_reg(USB2_PHY_RX_CHAN_CTRL1_ADDR(usb32),
                              rb_usb2phy_sqcal_done,    /* value */
                              rb_usb2phy_sqcal_done,    /* mask */
-                             PLL_LOCK_TIMEOUT,         /* timeout */
                              POLL_32B_REG);            /* 32bit */
        if (ret == 0)
                printf("Failed to end USB2 unknown calibration\n");
@@ -522,7 +515,6 @@ static int comphy_usb2_power_up(u8 usb32)
        ret = comphy_poll_reg(USB2_PHY_PLL_CTRL0_ADDR(usb32),
                              rb_usb2phy_pll_ready,             /* value */
                              rb_usb2phy_pll_ready,             /* mask */
-                             PLL_LOCK_TIMEOUT,         /* timeout */
                              POLL_32B_REG);            /* 32bit */
 
        if (ret == 0)
@@ -772,7 +764,6 @@ static int comphy_sgmii_power_up(u32 lane, u32 speed, u32 
invert)
        ret = comphy_poll_reg(COMPHY_PHY_STAT1_ADDR(lane),      /* address */
                              rb_pll_ready_tx | rb_pll_ready_rx, /* value */
                              rb_pll_ready_tx | rb_pll_ready_rx, /* mask */
-                             PLL_LOCK_TIMEOUT,                 /* timeout */
                              POLL_32B_REG);                    /* 32bit */
        if (ret == 0)
                printf("Failed to lock PLL for SGMII PHY %d\n", lane);
@@ -795,7 +786,6 @@ static int comphy_sgmii_power_up(u32 lane, u32 speed, u32 
invert)
        ret = comphy_poll_reg(COMPHY_PHY_STAT1_ADDR(lane), /* address */
                              rb_rx_init_done,                  /* value */
                              rb_rx_init_done,                  /* mask */
-                             PLL_LOCK_TIMEOUT,         /* timeout */
                              POLL_32B_REG);                    /* 32bit */
        if (ret == 0)
                printf("Failed to init RX of SGMII PHY %d\n", lane);
-- 
2.16.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot

Reply via email to