Le 09/04/2018 à 18:02, Guillaume Gardet a écrit :
Le 09/04/2018 à 17:18, Jean-Jacques Hiblot a écrit :
On 09/04/2018 16:46, Guillaume Gardet wrote:
Le 09/04/2018 à 16:21, Jean-Jacques Hiblot a écrit :
On 09/04/2018 16:03, Guillaume Gardet wrote:
Le 09/04/2018 à 15:58, Jean-Jacques Hiblot a écrit :
On 09/04/2018 14:02, Guillaume Gardet wrote:
Hi Jaehoon,
There are problems with SD card access on Samsung Chromebook (snow) with latest
master (and also 2018.05-rc1 and 2018.03).
eMMC is ok, but SD card access leads to 'unable to select a mode' problem. If I
disable HS mode, I can access the SD card without problem:
********************************************************************************
diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
index 23f642980bf..28f4fa0f213 100644
--- a/drivers/mmc/dw_mmc.c
+++ b/drivers/mmc/dw_mmc.c
@@ -508,7 +508,8 @@ void dwmci_setup_cfg(struct mmc_config *cfg, struct
dwmci_host *host,
cfg->host_caps |= MMC_MODE_4BIT;
cfg->host_caps &= ~MMC_MODE_8BIT;
}
- cfg->host_caps |= MMC_MODE_HS | MMC_MODE_HS_52MHz;
+ /* Temp workaround for Chromebook snow to avoid the 'unable to select a
mode' error */
+// cfg->host_caps |= MMC_MODE_HS | MMC_MODE_HS_52MHz;
cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
}
********************************************************************************
Once we try to select HS mode, all access to SD card result in failure, even
when trying to setup a lower frequency mode, including SD legacy at 25 MHz.
Any idea what is going? Maybe you have fixes pending?
Can try with MMC_MODE_HS | MMC_MODE_HS_52MHz but with a lower max-frequency
(<25MHz) ? It would be interesting to know if it could come from a frequency
limitation.
I already tried to change SD_HS freq (in mmc_mode2freq) from 50000000 to
25000000 with no difference.
Is there some pad configuration to do when using higher frequency?
I do not think so.
Can you enable the debug output and post a log ?
Here is the log from u-boot built from u-boot-mmc (latest commit: 21c2ac32b845)
Yes, I have no serial, so I retyped the messages, so I hope there is no typo:
**********************************************************************
selecting mode MMC legacy (freq : 0 MHz)
selecting mode MMC legacy (freq : 25 MHz)
sd card: widths [4, 1] modes [SD Legacy, SD High SPeed (50MHz)]
host: widths [4, 1] modes [MMC legacy, SD Legacy, MMC High Speed (26MHz), SD
High Speed (50MHz), MMC High Speed (52MHz), MMC DDR52 (52MHz)]
trying mode SD High Speed (50MHz) width 4 (at 50 MHz)
selecting mode SD High Speed (50 MHz) (freq : 50 MHz)
unable to read ssr
selecting mode SD Legacy (25 MHz) (freq : 25 MHz)
trying mode SD High Speed (50MHz) width 1 (at 50 MHz)
So it fails either in sd_select_bus_width() or sd_set_card_speed()
Can you try to limit the bus width to 1 ? Does it fail also at 50 MHz ?
Yes, it fails too.
If I disable sd_set_card_speed, then it is working fine.
Guillaume
Guillaume
selecting mode SD Legacy (25 MHz) (freq : 25 MHz)
trying mode SD Legacy (25MHz) width 4 (at 25 MHz)
selecting mode SD Legacy (25 MHz) (freq : 25 MHz)
trying mode SD Legacy (25MHz) width 1 (at 25 MHz)
selecting mode SD Legacy (25 MHz) (freq : 25 MHz)
unable to select a mode
mmc_init: -524, time 127
** Bad device mmc 1 **
**********************************************************************
Note that eMMC (on mmc 0) is working fine with MMC DDR52 (52MHz).
Guillaume
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
