Hi Jaehoon, Ping!
Thanks, Siva > -----Original Message----- > From: Siva Durga Prasad Paladugu > Sent: Tuesday, April 10, 2018 12:02 PM > To: Jaehoon Chung <jh80.ch...@samsung.com>; u-boot@lists.denx.de > Subject: RE: [PATCH v2 0/7] Add support of SD3.0 UHS modes for ZynqMP > > Hi Jaehoon, > > I would like to send v3 for this series, Any specific branch that you want me > to rebase the series? > > Thanks, > DP > > > -----Original Message----- > > From: Jaehoon Chung [mailto:jh80.ch...@samsung.com] > > Sent: Wednesday, January 17, 2018 8:04 AM > > To: Siva Durga Prasad Paladugu <siva...@xilinx.com>; u- > > b...@lists.denx.de > > Subject: Re: [PATCH v2 0/7] Add support of SD3.0 UHS modes for > ZynqMP > > > > Hi Siva, > > > > On 01/16/2018 07:10 PM, Siva Durga Prasad Paladugu wrote: > > > Hi Jaehoon, > > > > > > Any review comments on this. > > > > Thanks for reminding. Will check! :) > > > > Best Regards, > > Jaehoon Chung > > > > > > Thanks, > > > Siva > > > > > >> -----Original Message----- > > >> From: Siva Durga Prasad Paladugu > > >> [mailto:siva.durga.palad...@xilinx.com] > > >> Sent: Thursday, January 04, 2018 3:11 PM > > >> To: u-boot@lists.denx.de > > >> Cc: jh80.ch...@samsung.com; Siva Durga Prasad Paladugu > > >> <siva...@xilinx.com> > > >> Subject: [PATCH v2 0/7] Add support of SD3.0 UHS modes for ZynqMP > > >> > > >> This patch series is meant to add SD3.0 support for ZynqMP platform. > > >> The first five patches in the series mostly setting up things in > > >> sdhci layer to support SD3.0 , the sixth patch is to add SD3.0 > > >> support for ZynqMP platform and the last patch is to enable this > > >> support for ZynqMP zcu102 > > >> rev1.0 eval board. > > >> > > >> Repo: u-boot-mmc.git > > >> Branch: hs200-working > > >> > > >> Siva Durga Prasad Paladugu (7): > > >> mmc: sdhci: Add support for disabling clock > > >> mmc: sdhci: Handle execute tuning command in > sdhci_send_command > > >> sdhci: Add new sdhci ops for platform specific tuning and delays > > >> mmc: sdhci: Invoke platform specific tuning and delay routines > > >> mmc : sdhci: Read capabilities register1 and update host caps > > >> mmc: zynq_sdhci: Add support for SD3.0 > > >> zynqmp: zcu102: Enable UHS support for ZCU102 Rev1.0 board > > >> > > >> board/xilinx/zynqmp/Makefile | 2 + > > >> board/xilinx/zynqmp/tap_delays.c | 230 > > >> ++++++++++++++++++++++++++ > > >> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 2 + > > >> drivers/mmc/sdhci.c | 67 +++++++- > > >> drivers/mmc/zynq_sdhci.c | 230 > > >> +++++++++++++++++++++++++- > > >> include/sdhci.h | 9 + > > >> include/zynqmp_tap_delay.h | 20 +++ > > >> 7 files changed, 550 insertions(+), 10 deletions(-) create mode > > >> 100644 board/xilinx/zynqmp/tap_delays.c create mode 100644 > > >> include/zynqmp_tap_delay.h > > >> > > >> -- > > >> 2.7.4 > > > > > > > > > > > > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot