On Mon, Jun 4, 2018 at 9:54 PM, Vasily Khoruzhick <[email protected]> wrote: > On Fri, Jun 1, 2018 at 9:52 AM, Jagan Teki <[email protected]> wrote: >> On Mon, May 28, 2018 at 4:48 PM, Jagan Teki <[email protected]> >> wrote: >>> This series rework of previous version where it removes legacy >>> usb phy handling and added phy driver on generic-phy framework. >>> >>> Current implementation phy driver is unable to get pinctrl, clock >>> and reset details from DT since the dm code on these will add it future. >>> >>> Changes for v8, v9, v10: >>> - rebase on master >>> - collect Jun Acked-by >>> - add Linux commit id details for dt-binding patch >>> - fixed few commit messages >>> >>> Changes for v7: >>> - rebase on master >>> >>> Changes for v6: >>> - Create private config for passing through driver_data instead >>> directly passing musb_config. This make room for adding new >>> configs in coming patches. >>> - memset to pdata in musb-new/sunxi.c >>> >>> Changes for v5: >>> - Rework of previous series >>> - Used driver_data on sunxi.c since dt supported >>> - tested on bpi-m2-plus, orangepi_pc2/prime, bananapi-m64 >>> >>> Changes for v4: >>> - Rework of previous series >>> - Add Allwinner sun4i USB PHY driver >>> - Drop legacy arch/arm/mach-sunxi/usb_phy.c and related code >>> >>> Chen-Yu Tsai (1): >>> sunxi: clock: Fix OHCI clock gating for H3/H5 >>> >>> Jagan Teki (33): >>> usb: sunxi: Simplify ccm reg base code >>> musb: sunxi: Add proper macros instead of numericals >>> musb: sunxi: Use simple way to fill musb_hdrc pdata >>> musb: sunxi: Add fifo config >>> sunxi: clock: Fix clock gating for H3/H5/A64 >>> musb: sunxi: Add OTG device clkgate and reset for H3/H5 >>> musb: sunxi: Use BIT instead of numerical shift >>> musb: sunxi: Add support for H3/H5/A64 >>> phy: Add Allwinner A64 USB PHY driver >>> phy: sun4i-usb: Add id_detect and vbus_detect ops >>> phy: sun4i-usb: Add H3/H5 PHY config >>> phy: sun4i-usb: Add V3S PHY config >>> phy: sun4i-usb: Add A83T USB PHY config >>> phy: sun4i-usb: Add A10/A13/A20 PHY config >>> phy: sun4i-usb: Add A31 PHY config >>> phy: sun4i-usb: Add A33 USB PHY config >>> phy: sun4i-usb: Add A23 USB PHY config >>> device-tree-bindings: phy: Sync sun4i-usb-phy bindings >>> board: sunxi: Use generic-phy for board_usb_cable_connected >>> phy: sun4i-usb: Add a sunxi specific function for setting >>> squelch-detect >>> usb: sunxi: Switch to use generic-phy >>> sunxi: Drop legacy usb_phy.c >>> arm64: allwinner: a64: bananapi-m64: Sync usb_otg node from Linux >>> configs: bananapi-m64: Enable USB OTG peripheral mode >>> ARM: dts: sun8i: a83t: Sync usbphy node from Linux >>> arm64: allwinner: a64: bananapi-m64: Sync usb host nodes from Linux >>> ARM: dts: sun8i-h3: bananapi-m2-plus: Sync usb otg nodes from Linux >>> configs: bananapi-m2-plus: Enable USB OTG peripheral mode >>> arm64: allwinner: h5: orangepi-pc2: Order nodes in alphabetic >>> arm64: allwinner: h5: orangepi-pc2: Sync usb otg nodes from Linux >>> configs: orangepi-pc2: Enable USB OTG peripheral mode >>> arm64: allwinner: h5: orangepi-prime: Sync usb otg nodes from Linux >>> configs: orangepi-prime: Enable USB OTG peripheral mode >>> >>> Jun Nie (1): >>> sunxi: h3: Sync OTG and HCI nodes from Linux DT >> >> Applied to u-boot-sunxi/master > > Hi Jagan, > > Have you tested these patches on A64 boards? It doesn't work for me on > Pinebook anymore.
Relevant logs with DEBUG enabled in drivers/phy/allwinner/phy-sun4i-usb.c: starting USB... USB0: Allwinner Sun4I USB PHY driver loaded sun4i_usb_phy_xlate: phy_id = 1 USB EHCI 0.00 USB1: sun4i_usb_phy_xlate: phy_id = 1 USB OHCI 0.0 Note that EHCI and OHCI versions are wrong. It was 1.00 for EHCI and 1.0 for OHCI before these changes. > > Regards, > Vasily > >> _______________________________________________ >> U-Boot mailing list >> [email protected] >> https://lists.denx.de/listinfo/u-boot _______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
