On 06/06/2018 04:16 AM, Pramod Kumar wrote: > LS1012A-FRDM and LS1012A-FRWY board. > > 1-Move all common files applicable for both boards LS1012A-FRDM > and LS1012A-FRWY into board directory ls1012afrx. > 2-Restructure LS1012A-FRDM code. Only board specific files are > in LS1012A-FRDM board directory. > > Signed-off-by: Pramod Kumar <pramod.kuma...@nxp.com> > --- > Depends on: > http://patchwork.ozlabs.org/patch/918935/ > http://patchwork.ozlabs.org/patch/918933/ > http://patchwork.ozlabs.org/patch/918932/ > > Changes for v2: > - Rebased patch to above dependency patches > > arch/arm/Kconfig | 2 + > board/freescale/ls1012afrdm/Kconfig | 60 > ---------------------- > board/freescale/ls1012afrdm/MAINTAINERS | 12 +---- > board/freescale/ls1012afrdm/Makefile | 4 +- > board/freescale/ls1012afrx/Kconfig | 27 ++++++++++ > board/freescale/{ls1012afrdm => ls1012afrx}/eth.c | 0 > .../ls1012afrdm.c => ls1012afrx/ls1012afrx.c} | 0 > 7 files changed, 32 insertions(+), 73 deletions(-) > create mode 100644 board/freescale/ls1012afrx/Kconfig > rename board/freescale/{ls1012afrdm => ls1012afrx}/eth.c (100%) > rename board/freescale/{ls1012afrdm/ls1012afrdm.c => > ls1012afrx/ls1012afrx.c} (100%) > > diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig > index 22234cd..ffff190 100644 > --- a/arch/arm/Kconfig > +++ b/arch/arm/Kconfig > @@ -1417,6 +1417,8 @@ source "board/freescale/ls1046ardb/Kconfig" > source "board/freescale/ls1012aqds/Kconfig" > source "board/freescale/ls1012ardb/Kconfig" > source "board/freescale/ls1012afrdm/Kconfig" > +source "board/freescale/ls1012afrx/Kconfig" > +source "board/freescale/ls1012afrwy/Kconfig" > source "board/freescale/mx35pdk/Kconfig" > source "board/freescale/s32v234evb/Kconfig" > source "board/gdsys/a38x/Kconfig" > diff --git a/board/freescale/ls1012afrdm/Kconfig > b/board/freescale/ls1012afrdm/Kconfig > index f52a896..58e592d 100644 > --- a/board/freescale/ls1012afrdm/Kconfig > +++ b/board/freescale/ls1012afrdm/Kconfig > @@ -21,63 +21,3 @@ config SYS_LS_PPA_FW_ADDR > default 0x40400000 > > endif > - > -if FSL_PFE > - > -config BOARD_SPECIFIC_OPTIONS # dummy > - def_bool y > - select PHYLIB > - imply PHY_REALTEK > - imply PHY_ATHEROS > - > -config DDR_PFE_PHYS_BASEADDR > - hex "PFE DDR physical base address" > - default 0x03800000 > - > -config DDR_PFE_BASEADDR > - hex "PFE DDR base address" > - default 0x83800000 > - > -config PFE_EMAC1_PHY_ADDR > - hex "PFE DDR base address" > - default 0x2 > - > -config PFE_EMAC2_PHY_ADDR > - hex "PFE DDR base address" > - default 0x1 > - > -endif > - > -if TARGET_LS1012AFRWY > - > -config SYS_BOARD > - default "ls1012afrdm" > - > -config SYS_VENDOR > - default "freescale" > - > -config SYS_SOC > - default "fsl-layerscape" > - > -config SYS_CONFIG_NAME > - default "ls1012afrwy" > - > -config SYS_LS_PFE_FW_ADDR > - hex "Flash address of PFE firmware" > - default 0x40020000 > - > -config SYS_LS_PPA_FW_ADDR > - hex "PPA Firmware Addr" > - default 0x40060000 > - > -config SYS_LS_PPA_ESBC_ADDR > - hex "PPA Firmware HDR Addr" > - default 0x401f4000 > - > -config SYS_LS_PFE_ESBC_ADDR > - hex "PFE Firmware HDR Addr" > - default 0x401f8000 > - > -endif > - > -source "board/freescale/common/Kconfig"
Why do you remove this file, but only add it for ls1012afrx below? Doesn't ls1012afrdm use the same common file? Please rebase before sending another version. York _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
