Hi Heinrich/Rob,

Do we have any update on this issue.

Thanks,
Siva

> -----Original Message-----
> From: Vipul Kumar
> Sent: Monday, June 18, 2018 10:35 AM
> To: Heinrich Schuchardt <xypron.deb...@gmx.de>; u-boot@lists.denx.de
> Cc: Michal Simek <mich...@xilinx.com>; Siva Durga Prasad Paladugu
> <siva...@xilinx.com>; Rob Clark <robdcl...@gmail.com>; Łukasz Majewski
> <lu...@denx.de>; Simon Glass <s...@chromium.org>
> Subject: RE: [U-Boot] Issue with fat16 format
> 
> Hi Heinrich,
> 
> > -----Original Message-----
> > From: Heinrich Schuchardt [mailto:xypron.deb...@gmx.de]
> > Sent: Sunday, June 17, 2018 1:07 AM
> > To: Vipul Kumar <vip...@xilinx.com>; u-boot@lists.denx.de
> > Cc: Michal Simek <mich...@xilinx.com>; Siva Durga Prasad Paladugu
> > <siva...@xilinx.com>; Rob Clark <robdcl...@gmail.com>; Łukasz
> Majewski
> > <lu...@denx.de>; Simon Glass <s...@chromium.org>
> > Subject: Re: [U-Boot] Issue with fat16 format
> >
> > On 06/15/2018 08:37 AM, Vipul Kumar wrote:
> > > Hi,
> > >
> > > After formatting SD card in fat16 format in windows, we are facing
> > > issue. I
> > used git bisect and came to know that this issue is due to
> > 8eafae209c35932d9a6560809c55ee4641534236 commit.
> > >
> > > When we use "gparted" utility for formatting SD card in fat16 in
> > > linux, it
> > works fine.
> > >
> > > Please give your comments on this issue and point out what's causing
> > > this
> > issue.
> > >
> > > Regards,
> > > Vipul Kumar
> > >
> > >
> >
> > Hello Vipul,
> >
> > >> we are facing issue
> > could you, please, indicate what issue you face. Please, also tell
> > which configuration file you are using.
> 
> Configuration file: zynq_zc702_defconfig
> 
> Issue: We are using BOOT.BIN and fit image (Kernel image + dtb + rootfs) to
> boot the board. Board is booting till u-boot successfully but when it goes to
> read image.ub   for further booting, it gives below message:
> 
> ERROR:
> Hit any key to stop autoboot:  0
> Copying FIT from SD to RAM...
> ** Unable to read file image.ub **
> 
> After this, I run the fatls command and it seems that it removed both
> BOOT.BIN and image.ub files.
> 
> Zynq> mmc info
> Device: sdhci@e0100000
> Manufacturer ID: 27
> OEM: 5048
> Name: SD04G
> Bus Speed: 50000000
> Mode : SD High Speed (50MHz)
> Rd Block Len: 512
> SD version 3.0
> High Capacity: Yes
> Capacity: 3.7 GiB
> Bus Width: 4-bit
> Erase Group Size: 512 Bytes
> 
> Zynq> fatls mmc 0:1
> 
> 0 file(s), 0 dir(s)
> 
> Zynq>
> 
> 
> Regards,
> Vipul
> >
> > As you are complaining about Rob's patch I put him and the reviewers
> > of the patch on CC.
> >
> > Best regards
> >
> > Heinrich
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot

Reply via email to