On Mon, Jul 30, 2018 at 8:41 PM, Stefan Roese <s...@denx.de> wrote:
> Hi Miquel,
> Hi Jagan,
>
>
> On 26.07.2018 09:29, Miquel Raynal wrote:
>>
>> Hi Jagan,
>>
>> Jagan Teki <ja...@amarulasolutions.com> wrote on Thu, 26 Jul 2018
>> 11:00:56 +0530:
>>
>>> On Fri, Jul 13, 2018 at 6:01 PM, Miquel Raynal
>>> <miquel.ray...@bootlin.com> wrote:
>>>>
>>>> During the last months, Boris Brezillon shared his work to support
>>>> serial flashes within Linux. First, he delivered (and merged) a new
>>>> layer called spi-mem. He also initiated in Linux MTD subsystem the move
>>>> of all 'raw' NAND related code to a raw/ subdirectory, adding at the
>>>> same time a NAND core that would be shared with all NAND devices. Then,
>>>> he contributed a generic SPI-NAND driver, making use of this NAND core,
>>>> as well as some vendor code to drive a few chips.
>>>>
>>>> On top of this work, I added an 'mtd' U-Boot command to handle all sort
>>>> of MTD devices. This should become the default command instead of having
>>>> one per flash flavor ('sf', 'nand', 'spi-nand' ?).
>>>>
>>>> The series has been tested on an Ocelot board PCB123 (VSC7514),
>>>> featuring a Macronix SPI NAND chip.
>>>>
>>>> TL;DR: the series contains:
>>>> - A few patches from Linux to resynchronize some areas of the MTD layer.
>>>> - Various fixes and re-organization of the MTD subsystem.
>>>> - The introduction of the SPI-mem interface.
>>>> - The addition of the generic SPI-NAND driver (and its bindings).
>>>> - Several SPI NAND chip drivers (Macronix, Micron, Winbond).
>>>> - A new 'mtd' command.
>>>> - Support for spi-nand devices in mtdparts.
>>>>
>>>> To test your SPI-NAND device with U-Boot simply follow these lines:
>>>>
>>>>>
>>>>> setenv mtdparts mtdparts=spi-nand0:1m(foo),-(bar)
>>>>> setenv mtdids spi-nand0=spi-nand0
>>>>> mtdparts # show the spi-nand device partitions
>>>>> ubi part bar # create a static UBI volume in the bar partition
>>>>
>>>>
>>>> Thanks,
>>>> Miquèl
>>>>
>>>> Changes since v3:
>>>> -----------------
>>>> * Fixed the debug messages in spi-mem to print either Rx or Tx data.
>>>> * Fixed a Kconfig error that prevented to build mtdparts with plain
>>>> defconfig.
>>>> * Fixed a compilation error due to the above error that prevented one
>>>> file to be compiled.
>>>> * Adapted the mtd command to probe MTD partitions also.
>>>> * Declared mtd_probe_devices() in a header so mtdparts or UBI could
>>>> use it too (to probe all devices and MTD partitions in a clean way).
>>>> * As I worked on mtdparts, I found annoying and completely useless the
>>>> fact that we need to prefix the environment variable with
>>>> "mtdparts=". Canceled this obligation.
>>>> * Added one patch to allow spi-nand devices to be recognized by mtdparts
>>>> (this is purely useless but needed to be done in order to use this
>>>> command).
>>>> * Removed useless definitions of MTD device types in UBI code.
>>>> * Wrote a generic mtdparts environment variable parser, used by the mtd
>>>> command.
>>>> * Used the mtd_probe_devices() function from get_mtd_info() in
>>>> cmd/mtdparts.c to be sure the desired partition really does not exist
>>>> (otherwise it will be probed and then found).
>>>>
>>>> Changes since v2:
>>>> -----------------
>>>> * Rebased on u-boot master branch.
>>>> * Removed extra-parenthesis in
>>>> "mtd: Fallback to ->_read/write() when ->_read/write_oob() is
>>>> missing"
>>>> * s/fiels/files/ in "mtd: move NAND fiels into a raw/ subdirectory"
>>>> * Do not describe generic SPI device properties in SPI NAND bindings.
>>>> * Changes in the mtd command:
>>>> * Printing more information in 'mtd list' (device type, device
>>>> characteristics)
>>>> * Switch to do_div() instead of '(u32)value64b % value32b' which only
>>>> worked because value32b was a power of 2.
>>>> * Removed erase.chip option.
>>>> * By default, erase/read/write happen on the full MTD device while a
>>>> dump will only work on a single page.
>>>>
>>>> Changes since v1:
>>>> -----------------
>>>> * Fixed the nand_memorg structure of the MX35LF2GE4AB chip.
>>>> * Added Reviewed-by tags from Jagan.
>>>> * Backported and squashed two patches fixing things in the SPI NAND core
>>>> received on the Linux ML.
>>>> * Backported more changes in mtdcore.c from Linux.
>>>> * Added a patch to add a fallback on mtd->_read/_write() in mtdcore.c
>>>> when mtd->_read/write_oob() is not supported.
>>>> * Removed the DT changes, useless as the DTs are not available in
>>>> mainline yet.
>>>> * Addressed Boris/Stefan comments on the 'mtd' command.
>>>> * Added support for multi-pages OOB read/write.
>>>>
>>>>
>>>> Boris Brezillon (7):
>>>> mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
>>>> mtd: Add sanity checks in mtd_write/read_oob()
>>>> mtd: nand: Add core infrastructure to deal with NAND devices
>>>> mtd: nand: Pass mode information to nand_page_io_req
>>>> spi: Extend the core to ease integration of SPI memory controllers
>>>> mtd: spinand: Add initial support for the MX35LF1GE4AB chip
>>>> dt-bindings: Add bindings for SPI NAND devices
>>>>
>>>> Brian Norris (1):
>>>> mtd: add get/set of_node/flash_node helpers
>>>>
>>>> Ezequiel Garcia (1):
>>>> mtd: Uninline mtd_write_oob and move it to mtdcore.c
>>>>
>>>> Frieder Schrempf (1):
>>>> mtd: spinand: Add initial support for Winbond W25M02GV
>>>>
>>>> Miquel Raynal (15):
>>>> mtd: Fallback to ->_read/write() when ->_read/write_oob() is missing
>>>> mtd: fix build issue with includes
>>>> mtd: move definitions to enlarge their range
>>>> mtd: move all flash categories inside MTD submenu
>>>> mtd: move NAND files into a raw/ subdirectory
>>>> mtd: rename nand into rawnand in Kconfig prompt
>>>> mtd: spinand: Add initial support for the MX35LF2GE4AB chip
>>>> mtd: declare MTD_PARTITIONS symbol in Kconfig
>>>> cmd: ubi: delete useless and misleading definitions
>>>> cmd: mtdparts: accept spi-nand devices
>>>> cmd: mtdparts: add a generic 'mtdparts' parser
>>>> cmd: mtdparts: remove useless 'mtdparts=' prefix
>>>> mtd: uclass: add probe function
>>>> cmd: mtd: add 'mtd' command
>>>> cmd: mtdparts: try to probe the MTD devices as a fallback
>>>>
>>>> Peter Pan (2):
>>>> mtd: nand: Add core infrastructure to support SPI NANDs
>>>> mtd: spinand: Add initial support for Micron MT29F2G01ABAGD
>>>
>>>
>>> Acked--by: Jagan Teki <ja...@openedev.com>
>>>
>>
>> Thanks!
>>
>>> Can you rebase on master and send the needed patches or whole? Look
>>> like some changes been added in drivers/mtd/nand/Kconfig
>>
>>
>> I'll wait a bit for Stefan review also and I think I missed something
>> in mtdparts: old partitions are not freed when creating new ones.
Is this resolved with v5?
>
> I'm back from vacation and am starting to work on this SPI NAND
> support again. Right now, I'm facing a problem with 32 Bytes
> missing when written to NAND and read back. Most likely a problem
> with my SPI driver which supports a maximum of 32 Bytes per SPI
> message (I'm using adjust_op_size() to adjust the max xfer size).
Is it with kirkwood?
> As for waiting for my review comments, I would suggest to pull
> this patchset (once updated onto TOT) soon, as the merge window
> closes just today. We can fix issues later in this release cycle.
> Otherwise we need to postpone this series to the next release, which
> is of course also on option.
If the issue is generic and it changed the current behavior on mtd or
any other related areas, it's better to hold.
Jagan.
--
Jagan Teki
Senior Linux Kernel Engineer | Amarula Solutions
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
