Hello community, thank you for providing such a good software. I hope this is the right way to get help.
I successfully run my RPI3b with u-boot and buildroot. I have attached the
official 7“ touch display for the rpi. Which also works fine in linux.
When I want to display a bmp on the display in u-boot nothing is displayed and
no error is shown.
The following is the output on the serial console and also on the display:
```
U-Boot 2018.07 (Aug 20 2018 - 17:00:45 +0200)
DRAM: 768 MiB
RPI 3 Model B (0xa02082)
MMC: mmc@7e202000: 0, sdhci@7e300000: 1
Loading Environment from FAT... OK
In: serial
Out: vidconsole
Err: vidconsole
Net: No ethernet found.
starting USB...
USB0: Core Release: 2.80a
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autobot: 0
U-Boot> lcdputs hello
U-Boot> load mmc 0:7 $kernel_addr_r /splash-l32.bmp
1152054 bytes read in 50 ms (22 MiB/s)
U-Boot> bmp display $kernel_addr_r || echo error
U-Boot>
```
The console output and also lcdputs works on the display, but bmp display does
nothing and don’t print error.
This is my u-boot defconfig:
```
CONFIG_ARM=y
CONFIG_ARCH_BCM283X=y
CONFIG_SYS_TEXT_BASE=0x00008000
CONFIG_TARGET_RPI_3_32B=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_DEFAULT_DEVICE_TREE="bcm2837-rpi-3-b"
CONFIG_DISTRO_DEFAULTS=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_LOGLEVEL=7
# CONFIG_DISPLAY_CPUINFO is not set
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SYS_PROMPT="U-Boot> "
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_GPIO=y
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
CONFIG_CMD_BMP=y
CONFIG_OF_EMBED=y
CONFIG_ENV_FAT_INTERFACE="mmc"
CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_ENV=y
CONFIG_DM_KEYBOARD=y
CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_BCM2835=y
CONFIG_PHYLIB=y
CONFIG_DM_ETH=y
CONFIG_PINCTRL=y
# CONFIG_PINCTRL_GENERIC is not set
# CONFIG_REQUIRE_SERIAL_CONSOLE is not set
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_DWC2=y
CONFIG_USB_STORAGE=y
CONFIG_USB_KEYBOARD=y
CONFIG_USB_HOST_ETHER=y
CONFIG_USB_ETHER_LAN78XX=y
CONFIG_USB_ETHER_SMSC95XX=y
CONFIG_DM_VIDEO=y
CONFIG_SYS_WHITE_ON_BLACK=y
CONFIG_CONSOLE_SCROLL_LINES=10
CONFIG_PHYS_TO_BUS=y
CONFIG_OF_LIBFDT_OVERLAY=y
```
Thanks in advance
Christian Nienhaus
signature.asc
Description: Message signed with OpenPGP using GPGMail
_______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
