Hi Anand Moon, with U-Boot 2018.11-rc3-00062-g26cc40d8c4 and booting Fedora 28 Server I have no problems with a *warm boot* of my Odroid HC2. So I think this is not a general problem.
My u-boot.bin was created using: $ ARCH=arm CROSS_COMPILE=arm-linux-gnu- make odroid-xu3_defconfig $ ARCH=arm CROSS_COMPILE=arm-linux-gnu- make -j $(nproc) on Fedora 28 Workstation. BR, Dirk Am Montag, den 12.11.2018, 13:06 +0530 schrieb Anand Moon: > Hi Dirk Meul > > On Tue, 23 Oct 2018 at 16:08, Dirk Meul <[email protected]> > wrote: > > > > From: Dirk Meul <[email protected]> > > Date: Sun, 14 Oct 2018 17:14:17 +0200 > > > > Odroid HC2 board is based on Odroid XU4 board, like the Odroid HC1. > > > > The linux kernel does not provide a hc2 DTB so the hc1 DTB is also > > used > > for the Odroid HC2. > > > > Resend because MUA changed whitespace. > > > > Signed-off-by: Dirk Meul <[email protected]> > > Acked-by: Marek Szyprowski <[email protected]> > > Reviewed-by: Lukasz Majewski <[email protected]> > > --- > > board/samsung/common/exynos5-dt-types.c | 16 +++++++++++++--- > > board/samsung/common/exynos5-dt.c | 4 ++-- > > configs/odroid-xu3_defconfig | 2 +- > > include/samsung/exynos5-dt-types.h | 2 ++ > > 4 files changed, 18 insertions(+), 6 deletions(-) > > > > diff --git a/board/samsung/common/exynos5-dt-types.c > > b/board/samsung/common/exynos5-dt-types.c > > index 4473968db6..7a86e91877 100644 > > --- a/board/samsung/common/exynos5-dt-types.c > > +++ b/board/samsung/common/exynos5-dt-types.c > > @@ -24,14 +24,15 @@ static const struct udevice_id board_ids[] = { > > }; > > > > /** > > - * Odroix XU3/XU4/HC1 board revisions (from > > HC1_MAIN_REV0.1_20170630.pdf): > > + * Odroix XU3/XU4/HC1/HC2 board revisions (from > > HC1+_HC2_MAIN_REV0.1_20171017.pdf): > > * Rev ADCmax Board > > * 0.1 0 XU3 0.1 > > * 0.2 372 XU3 0.2 | XU3L - no DISPLAYPORT (probe I2C0:0x40 > > / INA231) > > * 0.3 1280 XU4 0.1 > > * 0.4 739 XU4 0.2 > > * 0.5 1016 XU4+Air0.1 (Passive cooling) > > - * 0.6 1308 XU4S 0.1 (HC1) > > + * 0.6 1309 XU4-HC1 0.1 > > + * 0.7 1470 XU4-HC1+ 0.1 (HC2) > > * Use +1% for ADC value tolerance in the array below, the code > > loops until > > * the measured ADC value is lower than then ADCmax from the > > array. > > */ > > @@ -39,7 +40,8 @@ struct odroid_rev_info odroid_info[] = { > > { EXYNOS5_BOARD_ODROID_XU3_REV01, 1, 10, "xu3" }, > > { EXYNOS5_BOARD_ODROID_XU3_REV02, 2, 375, "xu3" }, > > { EXYNOS5_BOARD_ODROID_XU4_REV01, 1, 1293, "xu4" }, > > - { EXYNOS5_BOARD_ODROID_HC1_REV01, 1, 1321, "hc1" }, > > + { EXYNOS5_BOARD_ODROID_HC1_REV01, 1, 1322, "hc1" }, > > + { EXYNOS5_BOARD_ODROID_HC2_REV01, 1, 1484, "hc1" }, > > { EXYNOS5_BOARD_ODROID_UNKNOWN, 0, 4095, "unknown" }, > > }; > > > > @@ -144,6 +146,14 @@ bool board_is_odroidhc1(void) > > return false; > > } > > > > +bool board_is_odroidhc2(void) > > +{ > > + if (gd->board_type == EXYNOS5_BOARD_ODROID_HC2_REV01) > > + return true; > > + > > + return false; > > +} > > + > > bool board_is_generic(void) > > { > > if (gd->board_type == EXYNOS5_BOARD_GENERIC) > > diff --git a/board/samsung/common/exynos5-dt.c > > b/board/samsung/common/exynos5-dt.c > > index 8c3a9ea564..c183965b92 100644 > > --- a/board/samsung/common/exynos5-dt.c > > +++ b/board/samsung/common/exynos5-dt.c > > @@ -179,7 +179,7 @@ char *get_dfu_alt_system(char *interface, char > > *devstr) > > { > > char *info = "Not supported!"; > > > > - if (board_is_odroidxu4() || board_is_odroidhc1()) > > + if (board_is_odroidxu4() || board_is_odroidhc1() || > > board_is_odroidhc2()) > > return info; > > > > return env_get("dfu_alt_system"); > > @@ -192,7 +192,7 @@ char *get_dfu_alt_boot(char *interface, char > > *devstr) > > char *alt_boot; > > int dev_num; > > > > - if (board_is_odroidxu4() || board_is_odroidhc1()) > > + if (board_is_odroidxu4() || board_is_odroidhc1() || > > board_is_odroidhc2()) > > return info; > > > > dev_num = simple_strtoul(devstr, NULL, 10); > > diff --git a/configs/odroid-xu3_defconfig b/configs/odroid- > > xu3_defconfig > > index 258b9781cc..d5c7cc7129 100644 > > --- a/configs/odroid-xu3_defconfig > > +++ b/configs/odroid-xu3_defconfig > > @@ -2,7 +2,7 @@ CONFIG_ARM=y > > CONFIG_ARCH_EXYNOS=y > > CONFIG_SYS_TEXT_BASE=0x43E00000 > > CONFIG_ARCH_EXYNOS5=y > > -CONFIG_IDENT_STRING=" for ODROID-XU3/XU4/HC1" > > +CONFIG_IDENT_STRING=" for ODROID-XU3/XU4/HC1/HC2" > > CONFIG_DISTRO_DEFAULTS=y > > CONFIG_NR_DRAM_BANKS=8 > > # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set > > diff --git a/include/samsung/exynos5-dt-types.h > > b/include/samsung/exynos5-dt-types.h > > index 8e11af30d1..8fe08fe211 100644 > > --- a/include/samsung/exynos5-dt-types.h > > +++ b/include/samsung/exynos5-dt-types.h > > @@ -9,6 +9,7 @@ enum { > > EXYNOS5_BOARD_ODROID_XU3_REV02, > > EXYNOS5_BOARD_ODROID_XU4_REV01, > > EXYNOS5_BOARD_ODROID_HC1_REV01, > > + EXYNOS5_BOARD_ODROID_HC2_REV01, > > EXYNOS5_BOARD_ODROID_UNKNOWN, > > > > EXYNOS5_BOARD_COUNT, > > @@ -25,5 +26,6 @@ bool board_is_generic(void); > > bool board_is_odroidxu3(void); > > bool board_is_odroidxu4(void); > > bool board_is_odroidhc1(void); > > +bool board_is_odroidhc2(void); > > > > #endif > > -- > > I think on reboot boot on Odroid HC1 and Odroid HC2 is broken. > I am testing on Arch Linux XU3/XU4 distro and it fails to boot after > *warm boot*. > I have tested this on Odroid HC1 and Odroid HC2 the result is the > same. > > Below is the debug logs. > ------------------------------------------------------------------- > ---------------------------------- > [ 577.135979] usb 4-1: reset SuperSpeed Gen 1 USB device number 2 > using xhci-hc > d > [ 577.312156] reboot: Restarting > > U-Boot 2018.11-rc3-00062-g26cc40d8c4-dirty (Nov 12 2018 - 06:51:53 > +0000) for ODROID-XU3/XU4/HC1/HC2 > > CPU: Exynos5422 @ 800 MHz > Model: Odroid XU3 based on EXYNOS5422 > Board: Odroid XU3 based on EXYNOS5422 > DRAM: 2 GiB > MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 2 > Loading Environment from MMC... Card did not respond to voltage > select! > *** Warning - No block device, using default environment > > In: serial > Out: serial > Err: serial > Net: No ethernet found. > Hit any key to stop autoboot: 0 > MMC Device 1 not found > no mmc device at slot 1 > Card did not respond to voltage select! > switch to partitions #0, OK > mmc2 is current device > Scanning mmc 2:1... > Found U-Boot script /boot/boot.scr > 2046 bytes read in 7 ms (285.2 KiB/s) > ## Executing script at 50000000 > 6782384 bytes read in 504 ms (12.8 MiB/s) > ** File not found /boot/dtbs/exynos5422-odroid.dtb ** > SCRIPT FAILED: continuing... > starting USB... > USB0: USB EHCI 1.00 > USB1: Register 2000140 NbrPorts 2 > Starting the controller > USB XHCI 1.00 > USB2: Register 2000140 NbrPorts 2 > Starting the controller > USB XHCI 1.00 > scanning bus 0 for devices... 1 USB Device(s) found > scanning bus 1 for devices... cannot reset port 1!? > 2 USB Device(s) found > scanning bus 2 for devices... 2 USB Device(s) found > scanning usb for storage devices... 1 Storage Device(s) found > scanning usb for ethernet devices... 1 Ethernet Device(s) > found > Waiting for Ethernet connection... done. > BOOTP broadcast 1 > BOOTP broadcast 2 > DHCP client bound to address 10.0.0.154 (848 ms) > *** ERROR: `serverip' not set > Cannot autoload with TFTPGET > missing environment variable: pxeuuid > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0A00009A > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0A00009 > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0A0000 > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0A000 > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0A00 > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0A0 > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0A > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0 > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/default-arm-exynos > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/default-arm > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/default > *** ERROR: `serverip' not set > Config file not found > BOOTP broadcast 1 > BOOTP broadcast 2 > DHCP client bound to address 10.0.0.154 (567 ms) > *** ERROR: `serverip' not set > Cannot autoload with TFTPGET > BOOTP broadcast 1 > DHCP client bound to address 10.0.0.154 (204 ms) > *** ERROR: `serverip' not set > Cannot autoload with TFTPGET > ODROID-XU3 # > ------------------------------------------------------------------- > ------------------------------------------------------------------- > -------- > Only after disconnecting and reconnect the power cable it start to > boot again normally. ie cold boot. > ------------------------------------------------------------------- > ------------------------------------------------------------------- > -------- > U-Boot 2018.11-rc3-00062-g26cc40d8c4-dirty (Nov 12 2018 - 06:51:53 > +0000) for ODROID-XU3/XU4/HC1/HC2 > > CPU: Exynos5422 @ 800 MHz > Model: Odroid XU3 based on EXYNOS5422 > Board: Odroid XU3 based on EXYNOS5422 > Type: hc1 > DRAM: 2 GiB > MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 2 > Loading Environment from MMC... Card did not respond to voltage > select! > *** Warning - No block device, using default environment > > In: serial > Out: serial > Err: serial > Net: No ethernet found. > Hit any key to stop autoboot: 0 > MMC Device 1 not found > no mmc device at slot 1 > Card did not respond to voltage select! > switch to partitions #0, OK > mmc2 is current device > Scanning mmc 2:1... > Found U-Boot script /boot/boot.scr > 2046 bytes read in 6 ms (333 KiB/s) > ## Executing script at 50000000 > 6782384 bytes read in 504 ms (12.8 MiB/s) > 53878 bytes read in 16 ms (3.2 MiB/s) > 5664652 bytes read in 420 ms (12.9 MiB/s) > Kernel image @ 0x42000000 [ 0x000000 - 0x677db0 ] > ## Flattened Device Tree blob at 43000000 > Booting using the fdt blob at 0x43000000 > Loading Ramdisk to 4fa99000, end 4fffff8c ... OK > Loading Device Tree to 4fa88000, end 4fa98275 ... OK > > Is their any other thing I could try to get this thing working. > > Best Regards > -Anand _______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
