This patch series converts PCM052 and BK4 to use Driver Model and Device Tree. Some notable changes: - The way how MAC address is read from fuses can now be adjusted - DTS improvement/sync with kernel - Using generic code instead of one from board
The output of u-boot boot: U-Boot 2019.01-rc3-00076-gc149229be0 (Jan 14 2019 - 08:38:48 +0100) CPU: Freescale Vybrid VF610 at 396 MHz Reset cause: POWER ON RESET Model: Liebherr (LVF) BK4 Vybrid Board Board: BK4r1 (L333) DRAM: 512 MiB NAND: 1024 MiB MMC: FSL_SDHC: 0 Loading Environment from NAND... OK In: serial@40028000 Out: serial@40028000 Err: serial@40028000 Net: eth0: fec@400d0000, eth1: fec@400d1000 Enter passphrase to stop autoboot, booting in 3 seconds Buildman CI: ./tools/buildman/buildman.py --branch=HEAD~3 vf610 mx6 vybrid --detail --verbose --show_errors --force-build --count=21 --output-dir=../BUILD/ Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/jobs/479284276 [omitting test_efi_selftest failure - as PCM052/BK4 is not supporting EFI] U-boot master branch: SHA1: b3a69c246915bd704d6073bcf4614d6881c0da04 Lukasz Majewski (21): ARM: DTS: vybrid: Add vf-u-boot.dtsi to set 'u-boot,dm-pre-reloc' in soc net: FEC: Add compatible for vybrid (vf610) to reuse fec_mxc.c driver net: Kconfig: FEC: Add dependency on VF610 vybrid: ddr: Extend vf610-pinfunc.h with DDR pads definitions vybrid: clock: Provide enable_i2c_clk() function for Vybrid vybrid: Define the imx_get_mac_from_fuse() as a __weak function pcm052: board: Remove "m4go" command as it is superseded by "bootaux" pcm052: board: vybrid: Update the board name for BK4 device ARM: DTS: vybrid: Update vf.dtsi file to descibe more vf610 hardware pcm052: board: cosmetic: Add copyright notice to pcm052.c ARM: DTS: Update pcm052 based dts files (bk4r1/pcm052.dts) defconfig: bk4/pcm052: Update bk4r1|pcm052_defconfig to support DM/DT config: pcm052: Use SZ_X{MK} from linux/sizes.h for include/configs/pcm052.h config: bk4: Update include/configs/bk4r1.h file pcm052: board: Remove in-board setup code (it is now replaced by DM setup) config: bk4: Update u-boot script to support recovery via SD card config: bk4: Update u-boot envs to support NOR memories initial setup pcm052: bk4: sdcard: Add support for SD card booting/recovery pcm052: board: Add code to setup LED default states pcm052: mac: Provide board specific imx_get_mac_from_fuse() function pcm052: bk4: Add board_phy_config() for BK4 to setup ksz8081 phy arch/arm/cpu/armv7/vf610/Kconfig | 1 + arch/arm/cpu/armv7/vf610/generic.c | 21 +- arch/arm/dts/bk4r1.dts | 108 +++++--- arch/arm/dts/pcm052.dts | 6 +- arch/arm/dts/vf-u-boot.dtsi | 11 + arch/arm/dts/vf.dtsi | 63 +++++ arch/arm/dts/vf610-pcm052.dtsi | 266 ++++++++++++++++++++ arch/arm/dts/vf610-pinfunc.h | 50 ++++ arch/arm/include/asm/arch-vf610/clock.h | 3 + arch/arm/include/asm/arch-vf610/imx-regs.h | 2 + board/phytec/pcm052/pcm052.c | 386 +++++++---------------------- configs/bk4r1_defconfig | 46 +++- configs/pcm052_defconfig | 32 ++- drivers/net/Kconfig | 2 +- drivers/net/fec_mxc.c | 1 + include/configs/bk4r1.h | 263 +++++++++++++++++++- include/configs/pcm052.h | 51 +--- 17 files changed, 925 insertions(+), 387 deletions(-) create mode 100644 arch/arm/dts/vf-u-boot.dtsi create mode 100644 arch/arm/dts/vf610-pcm052.dtsi -- 2.11.0 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
