Clearly separate bootcmd for stm32mp1 board
(bootcmd_stm32mp) and preboot management.
That solve issue for fastboot continue command.
Signed-off-by: Patrick Delaunay <patrick.delau...@st.com>
---
board/st/stm32mp1/stm32mp1.c | 1 +
configs/stm32mp15_basic_defconfig | 1 +
configs/stm32mp15_trusted_defconfig | 1 +
include/configs/stm32mp1.h | 37 +++++++++++++++++++++++++++----------
4 files changed, 30 insertions(+), 10 deletions(-)
diff --git a/board/st/stm32mp1/stm32mp1.c b/board/st/stm32mp1/stm32mp1.c
index 48da459..0d963c2 100644
--- a/board/st/stm32mp1/stm32mp1.c
+++ b/board/st/stm32mp1/stm32mp1.c
@@ -14,6 +14,7 @@
#include <usb.h>
#include <asm/arch/stm32.h>
#include <asm/io.h>
+#include <asm/gpio.h>
#include <power/regulator.h>
#include <usb/dwc2_udc.h>
diff --git a/configs/stm32mp15_basic_defconfig
b/configs/stm32mp15_basic_defconfig
index b1d09fb..4ab29ee 100644
--- a/configs/stm32mp15_basic_defconfig
+++ b/configs/stm32mp15_basic_defconfig
@@ -5,6 +5,7 @@ CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL=y
CONFIG_TARGET_STM32MP1=y
CONFIG_DISTRO_DEFAULTS=y
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
CONFIG_SPL_I2C_SUPPORT=y
diff --git a/configs/stm32mp15_trusted_defconfig
b/configs/stm32mp15_trusted_defconfig
index 9be7319..1bb3d0d 100644
--- a/configs/stm32mp15_trusted_defconfig
+++ b/configs/stm32mp15_trusted_defconfig
@@ -3,6 +3,7 @@ CONFIG_ARCH_STM32MP=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_STM32MP1=y
CONFIG_DISTRO_DEFAULTS=y
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
CONFIG_SYS_PROMPT="STM32MP> "
# CONFIG_CMD_BOOTD is not set
# CONFIG_CMD_ELF is not set
diff --git a/include/configs/stm32mp1.h b/include/configs/stm32mp1.h
index 4722672..48da1e3 100644
--- a/include/configs/stm32mp1.h
+++ b/include/configs/stm32mp1.h
@@ -10,8 +10,6 @@
#include <linux/sizes.h>
#include <asm/arch/stm32.h>
-#define CONFIG_PREBOOT
-
/*
* Number of clock ticks in 1 sec
*/
@@ -75,20 +73,38 @@
#define CONFIG_SYS_MMC_MAX_DEVICE 3
#define CONFIG_SUPPORT_EMMC_BOOT
-#if !defined(CONFIG_SPL) || !defined(CONFIG_SPL_BUILD)
+/*****************************************************************************/
+#ifdef CONFIG_DISTRO_DEFAULTS
+/*****************************************************************************/
+
+#if !defined(CONFIG_SPL_BUILD)
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 0) \
func(MMC, mmc, 2)
+/*
+ * bootcmd for stm32mp1:
+ * for serial/usb: execute the stm32prog command
+ * for mmc boot (eMMC, SD card), boot only on the same device
+ * for nand boot, boot with on ubifs partition on nand
+ * for nor boot, use the default order
+ */
+#define CONFIG_PREBOOT
-#include <config_distro_bootcmd.h>
+#define STM32MP_BOOTCMD "bootcmd_stm32mp=" \
+ "echo \"Boot over ${boot_device}${boot_instance}!\";" \
+ "if test ${boot_device} = serial || test ${boot_device} = usb;" \
+ "then stm32prog ${boot_device} ${boot_instance}; " \
+ "else " \
+ "if test ${boot_device} = mmc;" \
+ "then env set boot_targets \"mmc${boot_instance}\"; fi;" \
+ "if test ${boot_device} = nand;" \
+ "then env set boot_targets ubifs0; fi;" \
+ "run distro_bootcmd;" \
+ "fi;\0"
-#define STM32MP_PREBOOT \
- "echo \"Boot over ${boot_device}${boot_instance}!\"; " \
- "if test \"${boot_device}\" = \"mmc\"; then " \
- "env set boot_targets \"mmc${boot_instance}\"; "\
- "fi;"
+#include <config_distro_bootcmd.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
"scriptaddr=0xC0000000\0" \
@@ -98,9 +114,10 @@
"ramdisk_addr_r=0xC4100000\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
- "preboot=" STM32MP_PREBOOT "\0" \
+ STM32MP_BOOTCMD \
BOOTENV
#endif /* ifndef CONFIG_SPL_BUILD */
+#endif /* ifdef CONFIG_DISTRO_DEFAULTS*/
#endif /* __CONFIG_H */
--
2.7.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
