On Thu, 28 Feb 2019 22:13 Leigh Brown, <le...@solinno.co.uk> wrote: > Hi Chris, > > I tested together with my own patch. It fixes the issue, thanks very > much! >
Great. Thanks again for the bug report. Slightly related I've got a series of changes for USB on kirkwood. Would you be in a position to take them for a spin? > Tested-by: Leigh Brown <le...@solinno.co.uk> > > Output: > > U-Boot 2019.04-rc2-00134-g783e66816d-dirty (Feb 28 2019 - 08:27:16 > +0000) > Marvell-DreamPlug > > SoC: Kirkwood 88F6281_A1 > DRAM: 512 MiB > Loading Environment from SPI Flash... SF: Detected mx25l1606e with page > size 256 Bytes, erase size 4 KiB, total 2 MiB > OK > In: serial > Out: serial > Err: serial > Net: egiga0, egiga1 > 88E1116 Initialized on egiga0 > 88E1116 Initialized on egiga1 > IDE: ide_preinit failed > Hit any key to stop autoboot: 0 > starting USB... > USB0: USB EHCI 1.00 > scanning bus 0 for devices... 4 USB Device(s) found > scanning usb for storage devices... Device NOT ready > Request Sense returned 02 3A 00 > 1 Storage Device(s) found > 1879928 bytes read in 130 ms (13.8 MiB/s) > 9949 bytes read in 40 ms (242.2 KiB/s) > 2746404 bytes read in 163 ms (16.1 MiB/s) > ## Booting kernel from Legacy Image at 06000000 ... > Image Name: uImage-4.19.7+ > Created: 2018-12-06 14:10:50 UTC > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 1879864 Bytes = 1.8 MiB > Load Address: 00008000 > Entry Point: 00008000 > Verifying Checksum ... OK > ## Loading init Ramdisk from Legacy Image at 06600000 ... > Image Name: uInitrd-4.19.7+ > Created: 2018-12-06 14:10:50 UTC > Image Type: ARM Linux RAMDisk Image (uncompressed) > Data Size: 2746340 Bytes = 2.6 MiB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > ## Flattened Device Tree blob at 06400000 > Booting using the fdt blob at 0x6400000 > Loading Kernel Image ... OK > Loading Ramdisk to 0fd61000, end 0ffff7e4 ... OK > Loading Device Tree to 0fd5b000, end 0fd606dc ... OK > > Starting kernel ... > > On 2019-02-28 07:53, Chris Packham wrote: > > The conversion to DM_SPI managed to break accessing the environment on > > dreamplug. This is because the environment code relies on being to able > > to select the SPI device based on the sequence number. Add an alias so > > that the spi0 bus gets sequence number 0. > > > > Reported-by: Leigh Brown <le...@solinno.co.uk> > > Signed-off-by: Chris Packham <judge.pack...@gmail.com> > > --- > > Leigh, > > > > Could you test this on your system for me. I'm only able to compile > > test > > this myself. > > > > arch/arm/dts/kirkwood-dreamplug.dts | 4 ++++ > > 1 file changed, 4 insertions(+) > > > > diff --git a/arch/arm/dts/kirkwood-dreamplug.dts > > b/arch/arm/dts/kirkwood-dreamplug.dts > > index a647a65c20a0..ccd74dd7fb33 100644 > > --- a/arch/arm/dts/kirkwood-dreamplug.dts > > +++ b/arch/arm/dts/kirkwood-dreamplug.dts > > @@ -18,6 +18,10 @@ > > stdout-path = &uart0; > > }; > > > > + aliases { > > + spi0 = &spi0; > > + }; > > + > > ocp@f1000000 { > > pinctrl: pin-controller@10000 { > > pmx_led_bluetooth: pmx-led-bluetooth { > > Regards, > > Leigh. > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot