Hi Bin, Am Fr., 15. März 2019 um 09:03 Uhr schrieb Bin Meng <bmeng...@gmail.com>: > > Hi Christian, > > On Wed, Mar 13, 2019 at 5:27 PM Christian Gmeiner > <christian.gmei...@gmail.com> wrote: > > > > Hi all, > > > > Am Mo., 11. März 2019 um 15:41 Uhr schrieb Bin Meng <bmeng...@gmail.com>: > > > > > > Hi Andy, > > > > > > On Wed, Mar 6, 2019 at 7:09 PM Andy Shevchenko > > > <andriy.shevche...@linux.intel.com> wrote: > > > > > > > > On Thu, Feb 28, 2019 at 11:29:50AM +0800, Bin Meng wrote: > > > > > On Thu, May 24, 2018 at 12:00 PM Bin Meng <bmeng...@gmail.com> wrote: > > > > > > On Thu, Apr 12, 2018 at 4:07 PM, Christian Gmeiner > > > > > > <christian.gmei...@gmail.com> wrote: > > > > > > > > > So to me this seems to match my understanding about EIST. If this is > > > > > true, then I can't explain why Christian's patch is needed since the > > > > > EIST is disabled on TunnelCreek by default and the processor should > > > > > already run at the highest performance. > > > > > > > > The some internal documents I found suggesting that first what one > > > > needs to do > > > > is to be sure that EIST is enabled / disabled by reading a bit from > > > > CPUID. > > > > > > > > > > Correct. This is documented in the public Intel SDM too. > > > > > > > (There is no mention of the exact bit, I'm guessing it might be > > > > X86_FEATURE_EST) > > > > > > > > It also refers to IA32_MISC_ENABLE MSR, i.e. bit 20 > > > > (MSR_IA32_MISC_ENABLE_SPEEDSTEP_LOCK_BIT) and bit 16 > > > > (MSR_IA32_MISC_ENABLE_ENHANCED_SPEEDSTEP_BIT), that firmware can set up > > > > accordingly. > > > > > > > > Hope this helps. > > > > > > > > > > Thanks for the help. But I was looking for clarification on what > > > frequency the CPU is running at if EIST is disabled (the default > > > power-up state). Especially I suspect the Intel CPU is running at the > > > highest frequency when ESIT is disabled hence the highest performance. > > > Such details are not documented in the public Intel SDM. :( > > > > > > > P.S. All names are implying Linux kernel source code. > > > > > > > I think I need to clarify how I came to this patch. > > > > Back in the days when we used an Intel BLDK based BIOS solution we did > > some performance > > measurements and found out that the same device with an vendor BIOS is > > much faster. So we started > > to dig into the issue and used bandwidth to do our measurements. We > > contacted Intel to get support > > and after lot of ping-pong mails we got a solution. > > > > We need to set these two msr registers to the values they provided to us. > > These msr register should be described in #29324. > > Could you please provide details about these 2 MSR registers? And is > there any official document from Intel about what is the behavior of > having EIST disabled? >
I only got an excerpt of two pages describing these 2 MSR and I am quite sure I am not allowed to share these. As I wrote these MSR should be documented in #29324 (which I do not have access to). > > > > Bin do you have hardware to reproduce this issue I have and what gets > > fixed with this patch? > > Yes, I have the hardware to test. Is the test case able to run in > U-Boot? I can have a test. Boot into linux and run https://zsmith.co/bandwidth.html -- greets -- Christian Gmeiner, MSc https://christian-gmeiner.info _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot