On 5/20/19 2:45 AM, Marcel Ziswiler wrote: > Add MMC platform data. > > While at it also fix trivial checkpatch.pl issues. > > Signed-off-by: Marcel Ziswiler <mar...@ziswiler.com> > > --- > > board/toradex/colibri_pxa270/colibri_pxa270.c | 20 ++++++++++++++----- > 1 file changed, 15 insertions(+), 5 deletions(-) > > diff --git a/board/toradex/colibri_pxa270/colibri_pxa270.c > b/board/toradex/colibri_pxa270/colibri_pxa270.c > index e9e17508a5..507bf579cf 100644 > --- a/board/toradex/colibri_pxa270/colibri_pxa270.c > +++ b/board/toradex/colibri_pxa270/colibri_pxa270.c > @@ -3,7 +3,7 @@ > * Toradex Colibri PXA270 Support > * > * Copyright (C) 2010 Marek Vasut <marek.va...@gmail.com> > - * Copyright (C) 2016 Marcel Ziswiler <marcel.ziswi...@toradex.com> > + * Copyright (C) 2016-2019 Marcel Ziswiler <marcel.ziswi...@toradex.com> > */ > > #include <common.h> > @@ -14,6 +14,7 @@ > #include <asm/arch/regs-uart.h> > #include <asm/io.h> > #include <dm/platdata.h> > +#include <dm/platform_data/pxa_mmc_gen.h> > #include <dm/platform_data/serial_pxa.h> > #include <netdev.h> > #include <serial.h> > @@ -32,7 +33,7 @@ int board_init(void) > /* arch number of Toradex Colibri PXA270 */ > gd->bd->bi_arch_number = MACH_TYPE_COLIBRI; > > - /* adress of boot parameters */ > + /* address of boot parameters */ > gd->bd->bi_boot_params = 0xa0000100; > > return 0; > @@ -82,7 +83,7 @@ int board_usb_init(int index, enum usb_init_type init) > writel(readl(UHCRHDA) | 0x100, UHCRHDA); > > /* Set port power control mask bits, only 3 ports. */ > - writel(readl(UHCRHDB) | (0x7<<17), UHCRHDB); > + writel(readl(UHCRHDB) | (0x7 << 17), UHCRHDB);
setbits_le32(UHCRHDB, GEN_MASK(17, 19)); I think ? > /* enable port 2 */ > writel(readl(UP2OCR) | UP2OCR_HXOE | UP2OCR_HXS | > @@ -106,8 +107,6 @@ void usb_board_stop(void) > udelay(10); > > writel(readl(CKEN) & ~CKEN10_USBHOST, CKEN); > - > - return; > } > #endif > > @@ -119,11 +118,22 @@ int board_eth_init(bd_t *bis) > #endif > > #ifdef CONFIG_CMD_MMC > +#if !CONFIG_IS_ENABLED(DM_MMC) > int board_mmc_init(bd_t *bis) > { > pxa_mmc_register(0); > return 0; > } > +#else /* !CONFIG_IS_ENABLED(DM_MMC) */ > +static const struct pxa_mmc_plat mmc_platdata = { > + .base = (struct pxa_mmc_regs *)MMC0_BASE, > +}; > + > +U_BOOT_DEVICE(pxa_mmcs) = { > + .name = "pxa_mmc", > + .platdata = &mmc_platdata, > +}; > +#endif /* !CONFIG_IS_ENABLED(DM_MMC) */ > #endif > > static const struct pxa_serial_platdata serial_platdata = { > -- Best regards, Marek Vasut _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot