On 7/12/19 1:38 PM, Sam Protsenko wrote: > ttyO2 console enables legacy CONFIG_SERIAL_OMAP driver in kernel. > Nowadays it's preferred to use the generic CONFIG_SERIAL_8250_OMAP > driver, which being enabled via ttyS2 console. Both drivers are enabled > in multi_v7_defconfig and in omap2plus_defconfig, for compatibility > reasons. Let's switch to ttyS2 console, to be sure that standard 8250 > serial driver is used. > > Similar behavior can be also achieved by enabling > CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP option in kernel, but it's better not > to rely on that, as it can be disabled or removed after transitional > period. > > Right now on DRA7/AM57x platforms the 8250-omap driver is being probed > first, and omap-serial driver is only probed if the first one failed. > It can be seen from uart3 definition in arch/arm/boot/dts/dra7-l4.dtsi: > > compatible = "ti,dra742-uart", "ti,omap4-uart"; > > So the kernel already uses 8250 driver. This change basically allows > kernel developers to throw away the omap-serial driver and associated > compatibility options. Similar discussions [1,2] have started several > years ago, so it should be safe to do that now. > > [1] https://patchwork.kernel.org/patch/6198471/ > [2] > http://processors.wiki.ti.com/index.php/Sitara_Linux_UART_-_Switching_to_8250_Driver > > Signed-off-by: Sam Protsenko <semen.protse...@linaro.org> > --- > Changes in v2: > - use ttyS also in AM57x EVM and in DRA7xx EVM configs > > include/configs/am57xx_evm.h | 2 +- > include/configs/dra7xx_evm.h | 4 ++-- > include/environment/ti/boot.h | 2 +- > 3 files changed, 4 insertions(+), 4 deletions(-) > > diff --git a/include/configs/am57xx_evm.h b/include/configs/am57xx_evm.h > index 45fd21878c..e181b30564 100644 > --- a/include/configs/am57xx_evm.h > +++ b/include/configs/am57xx_evm.h > @@ -24,7 +24,7 @@ > > #define CONFIG_SYS_BOOTM_LEN SZ_64M > > -#define CONSOLEDEV "ttyO2" > +#define CONSOLEDEV "ttyS2" > #define CONFIG_SYS_NS16550_COM1 UART1_BASE /* Base EVM has > UART0 */ > #define CONFIG_SYS_NS16550_COM2 UART2_BASE /* UART2 */ > #define CONFIG_SYS_NS16550_COM3 UART3_BASE /* UART3 */ > diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h > index 9c8141de2e..7ec6e691c7 100644 > --- a/include/configs/dra7xx_evm.h > +++ b/include/configs/dra7xx_evm.h > @@ -26,9 +26,9 @@ > #endif > > #if (CONFIG_CONS_INDEX == 1)
This CONFIG_CONS_INDEX is not enabled for this platform, meaning the non-default console is chosen by default, it's not caused by this patch but while you are here could you fix that up? Just set: #define CONSOLEDEV "ttyS0" and drop all the #ifdef stuff, makes things a bit more clean. (and prevents a conflict with a patch I was going to send for the same) Andrew > -#define CONSOLEDEV "ttyO0" > +#define CONSOLEDEV "ttyS0" > #elif (CONFIG_CONS_INDEX == 3) > -#define CONSOLEDEV "ttyO2" > +#define CONSOLEDEV "ttyS2" > #endif > #define CONFIG_SYS_NS16550_COM1 UART1_BASE /* Base EVM has > UART0 */ > #define CONFIG_SYS_NS16550_COM2 UART2_BASE /* UART2 */ > diff --git a/include/environment/ti/boot.h b/include/environment/ti/boot.h > index 01b2981c5b..22206b9467 100644 > --- a/include/environment/ti/boot.h > +++ b/include/environment/ti/boot.h > @@ -10,7 +10,7 @@ > #define __TI_BOOT_H > > #ifndef CONSOLEDEV > -#define CONSOLEDEV "ttyO2" > +#define CONSOLEDEV "ttyS2" > #endif > > #define VBMETA_PART_SIZE (64 * 1024) > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot