Hi Joe, On Mon, 15 Jul 2019 at 22:17, Joe Hershberger <joe.hershber...@ni.com> wrote: > > On Sun, Jun 23, 2019 at 12:53 PM Vladimir Oltean <olte...@gmail.com> wrote: > > > > From: Jianchao Wang <jianchao.w...@nxp.com> > > > > The LS1021A-TSN is a development board built by VVDN/Argonboards in > > partnership with NXP. > > > > It features the LS1021A SoC and the first-generation SJA1105T Ethernet > > switch for prototyping implementations of a subset of IEEE 802.1 TSN > > standards. > > > > Supported boot media: microSD card (via SPL), QSPI flash. > > > > Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which > > is 64 MB in size and has an erase sector size of 256KB (therefore, > > flashing the RCW would erase part of U-boot). > > > > Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which > > is only 32 MB in size but has an erase sector size of 64KB (therefore > > the RCW image can be flashed without erasing U-boot). > > > > To avoid the problems above, the U-boot base address has been selected > > at 0x100000 (the start of the 5th 256KB erase sector), which works for > > all board revisions. Actually 0x40000 would have been enough, but > > 0x100000 is common for all Layerscape devices. > > > > eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but > > SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is > > disabled. > > > > Signed-off-by: Xiaoliang Yang <xiaoliang.y...@nxp.com> > > Signed-off-by: Mingkai Hu <mingkai...@nxp.com> > > Signed-off-by: Jianchao Wang <jianchao.w...@nxp.com> > > Signed-off-by: Changming Huang <jerry.hu...@nxp.com> > > > > [Vladimir] Code taken from https://github.com/openil/u-boot (which > > itself is mostly copied from ls1021a-iot) and adapted with the following > > changes: > > > > - Add a008850 errata workaround > > - Converted eTSEC, MMC to DM to avoid all build warnings > > - Plugged in distro boot feature, including support for extlinux.conf > > - Added defconfig for QSPI boot > > - Added the board/freescale/ls1021atsn/README.rst for initial setup > > > > Signed-off-by: Vladimir Oltean <olte...@gmail.com> > > --- > > arch/arm/Kconfig | 14 + > > arch/arm/dts/Makefile | 2 +- > > arch/arm/dts/ls1021a-tsn.dts | 77 ++++ > > board/freescale/ls1021atsn/Kconfig | 18 + > > board/freescale/ls1021atsn/MAINTAINERS | 8 + > > board/freescale/ls1021atsn/Makefile | 3 + > > board/freescale/ls1021atsn/README.rst | 96 +++++ > > board/freescale/ls1021atsn/ls1021atsn.c | 291 +++++++++++++++ > > board/freescale/ls1021atsn/ls102xa_pbi.cfg | 15 + > > board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg | 8 + > > configs/ls1021atsn_qspi_defconfig | 76 ++++ > > configs/ls1021atsn_sdcard_defconfig | 85 +++++ > > include/configs/ls1021atsn.h | 346 ++++++++++++++++++ > > 13 files changed, 1038 insertions(+), 1 deletion(-) > > create mode 100644 arch/arm/dts/ls1021a-tsn.dts > > create mode 100644 board/freescale/ls1021atsn/Kconfig > > create mode 100644 board/freescale/ls1021atsn/MAINTAINERS > > create mode 100644 board/freescale/ls1021atsn/Makefile > > create mode 100644 board/freescale/ls1021atsn/README.rst > > create mode 100644 board/freescale/ls1021atsn/ls1021atsn.c > > create mode 100644 board/freescale/ls1021atsn/ls102xa_pbi.cfg > > create mode 100644 board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg > > create mode 100644 configs/ls1021atsn_qspi_defconfig > > create mode 100644 configs/ls1021atsn_sdcard_defconfig > > create mode 100644 include/configs/ls1021atsn.h > > > > diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig > > index 01ff57cf1bec..5edac7ea2bd5 100644 > > --- a/arch/arm/Kconfig > > +++ b/arch/arm/Kconfig > > @@ -1327,6 +1327,19 @@ config TARGET_LS1021ATWR > > select SUPPORT_SPL > > imply SCSI > > > > +config TARGET_LS1021ATSN > > + bool "Support ls1021atsn" > > + select ARCH_LS1021A > > + select ARCH_SUPPORT_PSCI > > + select BOARD_EARLY_INIT_F > > + select BOARD_LATE_INIT > > + select CPU_V7A > > + select CPU_V7_HAS_NONSEC > > + select CPU_V7_HAS_VIRT > > + select LS1_DEEP_SLEEP > > + select SUPPORT_SPL > > + imply SCSI > > + > > config TARGET_LS1021AIOT > > bool "Support ls1021aiot" > > select ARCH_LS1021A > > @@ -1693,6 +1706,7 @@ source "board/freescale/ls1028a/Kconfig" > > source "board/freescale/ls1021aqds/Kconfig" > > source "board/freescale/ls1043aqds/Kconfig" > > source "board/freescale/ls1021atwr/Kconfig" > > +source "board/freescale/ls1021atsn/Kconfig" > > source "board/freescale/ls1021aiot/Kconfig" > > source "board/freescale/ls1046aqds/Kconfig" > > source "board/freescale/ls1043ardb/Kconfig" > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > > index 528fb909d5b0..28590b0c5530 100644 > > --- a/arch/arm/dts/Makefile > > +++ b/arch/arm/dts/Makefile > > @@ -325,7 +325,7 @@ dtb-$(CONFIG_TARGET_STV0991) += stv0991.dtb > > dtb-$(CONFIG_ARCH_LS1021A) += ls1021a-qds-duart.dtb \ > > ls1021a-qds-lpuart.dtb \ > > ls1021a-twr-duart.dtb ls1021a-twr-lpuart.dtb \ > > - ls1021a-iot-duart.dtb > > + ls1021a-iot-duart.dtb ls1021a-tsn.dtb > > dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ > > fsl-ls2080a-rdb.dtb \ > > fsl-ls2081a-rdb.dtb \ > > diff --git a/arch/arm/dts/ls1021a-tsn.dts b/arch/arm/dts/ls1021a-tsn.dts > > new file mode 100644 > > index 000000000000..f633074099dc > > --- /dev/null > > +++ b/arch/arm/dts/ls1021a-tsn.dts > > @@ -0,0 +1,77 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* Copyright 2016-2018 NXP Semiconductors > > + * Copyright 2019 Vladimir Oltean <olte...@gmail.com> > > + */ > > + > > +/dts-v1/; > > +#include "ls1021a.dtsi" > > + > > +/ { > > + model = "NXP LS1021A-TSN Board"; > > + > > + aliases { > > + enet0-sgmii-phy = &sgmii_phy2; > > + enet1-sgmii-phy = &sgmii_phy1; > > + spi0 = &qspi; > > + spi1 = &dspi1; > > + }; > > +}; > > + > > +&enet0 { > > + tbi-handle = <&tbi0>; > > + phy-handle = <&sgmii_phy2>; > > + phy-mode = "sgmii"; > > + status = "okay"; > > +}; > > + > > +&enet1 { > > + tbi-handle = <&tbi1>; > > + phy-handle = <&sgmii_phy1>; > > + phy-mode = "sgmii"; > > + status = "okay"; > > +}; > > + > > +&i2c0 { > > + status = "okay"; > > +}; > > + > > +&mdio0 { > > + /* AR8031 */ > > + sgmii_phy1: ethernet-phy@1 { > > + reg = <0x1>; > > + }; > > + > > + /* AR8031 */ > > + sgmii_phy2: ethernet-phy@2 { > > + reg = <0x2>; > > + }; > > + > > + /* SGMII PCS for enet0 */ > > + tbi0: tbi-phy@1f { > > + reg = <0x1f>; > > + device_type = "tbi-phy"; > > + }; > > +}; > > + > > +&mdio1 { > > + /* SGMII PCS for enet1 */ > > + tbi1: tbi-phy@1f { > > + reg = <0x1f>; > > + device_type = "tbi-phy"; > > + }; > > +}; > > + > > +&qspi { > > + bus-num = <0>; > > + status = "okay"; > > + > > + flash@0 { > > + compatible = "spi-flash"; > > + spi-max-frequency = <20000000>; > > + reg = <0>; > > + }; > > +}; > > + > > +&uart0 { > > + status = "okay"; > > +}; > > diff --git a/board/freescale/ls1021atsn/Kconfig > > b/board/freescale/ls1021atsn/Kconfig > > new file mode 100644 > > index 000000000000..d999fa469002 > > --- /dev/null > > +++ b/board/freescale/ls1021atsn/Kconfig > > @@ -0,0 +1,18 @@ > > +# SPDX-License-Identifier: GPL-2.0 > > +if TARGET_LS1021ATSN > > + > > +config SYS_BOARD > > + default "ls1021atsn" > > + > > +config SYS_VENDOR > > + default "freescale" > > + > > +config SYS_SOC > > + default "ls102xa" > > + > > +config SYS_CONFIG_NAME > > + default "ls1021atsn" > > + > > +source "board/freescale/common/Kconfig" > > + > > +endif > > diff --git a/board/freescale/ls1021atsn/MAINTAINERS > > b/board/freescale/ls1021atsn/MAINTAINERS > > new file mode 100644 > > index 000000000000..560bb615d2fe > > --- /dev/null > > +++ b/board/freescale/ls1021atsn/MAINTAINERS > > @@ -0,0 +1,8 @@ > > +NXP LS1021A-TSN Board > > +M: Vladimir Oltean <olte...@gmail.com> > > +S: Maintained > > +F: arch/arm/dts/ls1021a-tsn.dts > > +F: board/freescale/ls1021atsn/ > > +F: include/configs/ls1021atsn.h > > +F: configs/ls1021atsn_qspi_defconfig > > +F: configs/ls1021atsn_sdcard_defconfig > > diff --git a/board/freescale/ls1021atsn/Makefile > > b/board/freescale/ls1021atsn/Makefile > > new file mode 100644 > > index 000000000000..b4808f05e8e0 > > --- /dev/null > > +++ b/board/freescale/ls1021atsn/Makefile > > @@ -0,0 +1,3 @@ > > +# SPDX-License-Identifier: GPL-2.0 > > +obj-y += ls1021atsn.o > > +obj-$(CONFIG_ARMV7_PSCI) += ../ls1021atwr/psci.o > > diff --git a/board/freescale/ls1021atsn/README.rst > > b/board/freescale/ls1021atsn/README.rst > > new file mode 100644 > > index 000000000000..e986f460c4d4 > > --- /dev/null > > +++ b/board/freescale/ls1021atsn/README.rst > > @@ -0,0 +1,96 @@ > > +.. SPDX-License-Identifier: GPL-2.0 > > + > > +LS1021A-TSN Board Overview > > +========================== > > + > > + - 1GB DDR3 at 800 MHz > > + - Spansion/Cypress 64 MB (Rev. A) / 32 MB (Rev. B and C) QSPI NOR flash > > + - Ethernet > > + - 2 SGMII 10/100/1G Ethernet ports (Atheros AR8031) > > + - One SJA1105T switch with 4 Ethernet ports (Broadcom BCM5464R) > > + - One internal RGMII port connected to the switch > > + - SDHC > > + - microSDHC/SDXC connector > > + - Other I/O > > + - One Serial port > > + - Arduino and expansion headers > > + - mPCIE slot > > + - SATA port > > + - USB3.0 port > > + > > +LS1021A Memory map > > +================== > > + > > +The addresses in brackets are physical addresses. > > + > > +============== ============== ============================== ======= > > +Start Address End Address Description Size > > +============== ============== ============================== ======= > > +0x00_0000_0000 0x00_000F_FFFF Secure Boot ROM 1MB > > +0x00_0100_0000 0x00_0FFF_FFFF CCSRBAR 240MB > > +0x00_1000_0000 0x00_1000_FFFF OCRAM0 64KB > > +0x00_1001_0000 0x00_1001_FFFF OCRAM1 64KB > > +0x00_2000_0000 0x00_20FF_FFFF DCSR 16MB > > +0x00_4000_0000 0x00_5FFF_FFFF QSPI 512MB > > +0x00_6000_0000 0x00_67FF_FFFF IFC - NOR Flash 128MB > > +0x00_8000_0000 0x00_FFFF_FFFF DRAM1 2GB > > +============== ============== ============================== ======= > > + > > +Compiling and flashing > > +====================== > > + > > +The LS1021A-TSN board comes along with a microSD card with OpenIL U-boot. > > +That will be used to update the internal QSPI flash, as well as > > + > > +To compile and flash an SD card image:: > > + > > + make ls1021atsn_sdcard_defconfig && make -j 8 && sudo cp > > u-boot-with-spl-pbl.bin /srv/tftpboot/ > > + => tftp 0x82000000 u-boot-with-spl-pbl.bin && mmc rescan && mmc erase 8 > > 0x1100 && mmc write 0x82000000 8 0x1100 > > + > > +For the QSPI flash, first obtain the Reset Configuration Word binary for > > +bootimg from the QSPI flash from the rcw project > > +(https://source.codeaurora.org/external/qoriq/qoriq-components/rcw):: > > + > > + make -j 8 && sudo cp ls1021atsn/SSR_PNS_30/rcw_1200_qspiboot.bin.swapped > > /srv/tftpboot/ > > + > > +The above RCW binary takes care of swapping the QSPI AMBA memory, so that > > the > > +U-boot binary does not need to be swapped when flashing it. > > + > > +To compile and flash a U-boot image for QSPI:: > > + > > + make ls1021atsn_qspi_defconfig && make -j 8 && sudo cp u-boot.bin > > /srv/tftpboot/ > > + > > +Then optionally create a custom uboot-env.txt file (although the default > > +environment already supports distro boot) and convert it to binary format:: > > + > > + mkenvimage -s 2M -o /srv/tftpboot/uboot-env.bin uboot-env.txt > > + > > +To program the QSPI flash with the images:: > > + > > + => tftp 0x82000000 rcw_1000_qspiboot.bin.swapped && sf probe && sf erase > > 0x0 +${filesize} && sf write 0x82000000 0x0 ${filesize} > > + => tftp 0x82000000 u-boot.bin && sf probe && sf erase 0x100000 > > +${filesize} && sf write 0x82000000 0x100000 ${filesize} > > + => tftp 0x82000000 uboot-env.bin && sf probe && sf erase 0x400000 > > +${filesize} && sf write 0x82000000 0x400000 ${filesize} > > + > > +The boards contain an AT24 I2C EEPROM that is supposed to hold the MAC > > +addresses of the Ethernet interfaces, however the EEPROM comes blank out of > > +the factory, and the MAC addresses are printed on a label on the bottom of > > +the boards. > > + > > +To write the MAC addresses to the EEPROM, the following needs to be done > > once:: > > + > > + => mac id > > + => mac 0 00:1F:7B:xx:xx:xx > > + => mac 1 00:1F:7B:xx:xx:xx > > + => mac 2 00:1F:7B:xx:xx:xx > > + => mac save > > + > > +The switch ports do not have their own MAC address - they inherit it from > > the > > +master enet2 port. > > + > > +Known issues and limitations > > +============================ > > + > > +- The 4 SJA1105 switch ports are not functional in U-boot for now. > > +- Since the IFC pins are multiplexed with QSPI on LS1021A, currently there > > is > > + no way to talk to the CPLD for e.g. running the "qixis_reset" command, or > > + turning the fan on, etc. > > diff --git a/board/freescale/ls1021atsn/ls1021atsn.c > > b/board/freescale/ls1021atsn/ls1021atsn.c > > new file mode 100644 > > index 000000000000..84c2af142956 > > --- /dev/null > > +++ b/board/freescale/ls1021atsn/ls1021atsn.c > > @@ -0,0 +1,291 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* Copyright 2016-2019 NXP Semiconductors > > + */ > > +#include <common.h> > > +#include <i2c.h> > > +#include <asm/io.h> > > +#include <asm/arch/immap_ls102xa.h> > > +#include <asm/arch/clock.h> > > +#include <asm/arch/fsl_serdes.h> > > +#include <asm/arch-ls102xa/ls102xa_soc.h> > > +#include <asm/arch/ls102xa_devdis.h> > > +#include <asm/arch/ls102xa_soc.h> > > +#include <hwconfig.h> > > +#include <mmc.h> > > +#include <fsl_csu.h> > > +#include <fsl_esdhc.h> > > +#include <fsl_ifc.h> > > +#include <fsl_immap.h> > > +#include <netdev.h> > > +#include <spl.h> > > +#include "../common/sleep.h" > > +#ifdef CONFIG_U_QE > > +#include <fsl_qe.h> > > +#endif > > +#include <fsl_validate.h> > > + > > +DECLARE_GLOBAL_DATA_PTR; > > + > > +void cpld_show(void) > > +{ > > + struct ccsr_gur *dcfg = (struct ccsr_gur *)CONFIG_SYS_FSL_GUTS_ADDR; > > + u32 cpldrev; > > + int major; > > + int minor; > > + > > + cpldrev = in_be32(&dcfg->gpporcr1); > > + major = (cpldrev >> 28) & 0xf; > > + minor = (cpldrev >> 24) & 0xf; > > + > > + printf("CPLD: V%d.%d\n", major, minor); > > +} > > + > > +int checkboard(void) > > +{ > > + puts("Board: LS1021ATSN\n"); > > + cpld_show(); > > + return 0; > > +} > > + > > +void ddrmc_init(void) > > +{ > > + struct ccsr_ddr *ddr = (struct ccsr_ddr *)CONFIG_SYS_FSL_DDR_ADDR; > > + u32 temp_sdram_cfg, tmp; > > + > > + out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG); > > + > > + out_be32(&ddr->cs0_bnds, DDR_CS0_BNDS); > > + out_be32(&ddr->cs0_config, DDR_CS0_CONFIG); > > + > > + out_be32(&ddr->timing_cfg_0, DDR_TIMING_CFG_0); > > + out_be32(&ddr->timing_cfg_1, DDR_TIMING_CFG_1); > > + out_be32(&ddr->timing_cfg_2, DDR_TIMING_CFG_2); > > + out_be32(&ddr->timing_cfg_3, DDR_TIMING_CFG_3); > > + out_be32(&ddr->timing_cfg_4, DDR_TIMING_CFG_4); > > + out_be32(&ddr->timing_cfg_5, DDR_TIMING_CFG_5); > > + > > +#ifdef CONFIG_DEEP_SLEEP > > + if (is_warm_boot()) { > > + out_be32(&ddr->sdram_cfg_2, > > + DDR_SDRAM_CFG_2 & ~SDRAM_CFG2_D_INIT); > > + out_be32(&ddr->init_addr, CONFIG_SYS_SDRAM_BASE); > > + out_be32(&ddr->init_ext_addr, (1 << 31)); > > + > > + /* DRAM VRef will not be trained */ > > + out_be32(&ddr->ddr_cdr2, > > + DDR_DDR_CDR2 & ~DDR_CDR2_VREF_TRAIN_EN); > > + } else > > +#endif > > + { > > + out_be32(&ddr->sdram_cfg_2, DDR_SDRAM_CFG_2); > > + out_be32(&ddr->ddr_cdr2, DDR_DDR_CDR2); > > + } > > + > > + out_be32(&ddr->sdram_mode, DDR_SDRAM_MODE); > > + out_be32(&ddr->sdram_mode_2, DDR_SDRAM_MODE_2); > > + > > + out_be32(&ddr->sdram_interval, DDR_SDRAM_INTERVAL); > > + > > + out_be32(&ddr->ddr_wrlvl_cntl, DDR_DDR_WRLVL_CNTL); > > + > > + out_be32(&ddr->ddr_wrlvl_cntl_2, DDR_DDR_WRLVL_CNTL_2); > > + out_be32(&ddr->ddr_wrlvl_cntl_3, DDR_DDR_WRLVL_CNTL_3); > > + > > + out_be32(&ddr->ddr_cdr1, DDR_DDR_CDR1); > > + > > + out_be32(&ddr->sdram_clk_cntl, DDR_SDRAM_CLK_CNTL); > > + out_be32(&ddr->ddr_zq_cntl, DDR_DDR_ZQ_CNTL); > > + > > + out_be32(&ddr->cs0_config_2, DDR_CS0_CONFIG_2); > > + > > + /* DDR erratum A-009942 */ > > + tmp = in_be32(&ddr->debug[28]); > > + out_be32(&ddr->debug[28], tmp | 0x0070006f); > > + > > + udelay(1); > > + > > +#ifdef CONFIG_DEEP_SLEEP > > + if (is_warm_boot()) { > > + /* enter self-refresh */ > > + temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2); > > + temp_sdram_cfg |= SDRAM_CFG2_FRC_SR; > > + out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg); > > + > > + temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN | SDRAM_CFG_BI); > > + } else > > +#endif > > + temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN & ~SDRAM_CFG_BI); > > + > > + out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG | temp_sdram_cfg); > > + > > +#ifdef CONFIG_DEEP_SLEEP > > + if (is_warm_boot()) { > > + /* exit self-refresh */ > > + temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2); > > + temp_sdram_cfg &= ~SDRAM_CFG2_FRC_SR; > > + out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg); > > + } > > +#endif > > +} > > + > > +int dram_init(void) > > +{ > > +#if (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)) > > + ddrmc_init(); > > +#endif > > + > > + erratum_a008850_post(); > > + > > + gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); > > + > > +#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD) > > + fsl_dp_resume(); > > +#endif > > + > > + return 0; > > +} > > + > > +int board_eth_init(bd_t *bis) > > +{ > > + return pci_eth_init(bis); > > +} > > + > > +int board_early_init_f(void) > > +{ > > + struct ccsr_scfg *scfg = (struct ccsr_scfg > > *)CONFIG_SYS_FSL_SCFG_ADDR; > > + > > +#ifdef CONFIG_TSEC_ENET > > + /* Clear BD & FR bits for big endian BD's and frame data (aka set > > Nit: Multi-line comment format. I'm curious why checkpatch.pl doesn't > catch this sometimes. >
What seems to be the problem with this? Do you prefer to see a first line with just " /* "? > > + * correct eTSEC endianness). This is crucial in ensuring that it > > does > > + * not report Data Parity Errors in its RX/TX FIFOs when attempting > > to > > + * send traffic. > > + */ > > + clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); > > + /* EC3_GTX_CLK125 (of enet2) used for all RGMII interfaces */ > > + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); > > +#endif > > + > > +#ifdef CONFIG_FSL_IFC > > + init_early_memctl_regs(); > > +#endif > > + > > + arch_soc_init(); > > + > > +#if defined(CONFIG_DEEP_SLEEP) > > + if (is_warm_boot()) { > > + timer_init(); > > + dram_init(); > > + } > > +#endif > > + > > + return 0; > > +} > > + > > +#ifdef CONFIG_SPL_BUILD > > +void board_init_f(ulong dummy) > > +{ > > + void (*second_uboot)(void); > > + > > + /* Clear the BSS */ > > + memset(__bss_start, 0, __bss_end - __bss_start); > > + > > + get_clocks(); > > + > > +#if defined(CONFIG_DEEP_SLEEP) > > + if (is_warm_boot()) > > + fsl_dp_disable_console(); > > +#endif > > + > > + preloader_console_init(); > > + > > + dram_init(); > > + > > + /* Allow OCRAM access permission as R/W */ > > +#ifdef CONFIG_LAYERSCAPE_NS_ACCESS > > + enable_layerscape_ns_access(); > > + enable_layerscape_ns_access(); > > +#endif > > + > > + /* > > + * if it is woken up from deep sleep, then jump to second > > + * stage uboot and continue executing without recopying > > U-Boot > > > + * it from SD since it has already been reserved in memory > > + * in last boot. > > + */ > > + if (is_warm_boot()) { > > + second_uboot = (void (*)(void))CONFIG_SYS_TEXT_BASE; > > + second_uboot(); > > + } > > + > > + board_init_r(NULL, 0); > > +} > > +#endif > > + > > +int board_init(void) > > +{ > > +#ifndef CONFIG_SYS_FSL_NO_SERDES > > + fsl_serdes_init(); > > +#endif > > + ls102xa_smmu_stream_id_init(); > > + > > +#ifdef CONFIG_LAYERSCAPE_NS_ACCESS > > + enable_layerscape_ns_access(); > > +#endif > > + > > +#ifdef CONFIG_U_QE > > + u_qe_init(); > > +#endif > > + > > + return 0; > > +} > > + > > +#if defined(CONFIG_SPL_BUILD) > > +void spl_board_init(void) > > +{ > > + ls102xa_smmu_stream_id_init(); > > +} > > +#endif > > + > > +#ifdef CONFIG_BOARD_LATE_INIT > > +int board_late_init(void) > > +{ > > +#ifdef CONFIG_CHAIN_OF_TRUST > > + fsl_setenv_chain_of_trust(); > > +#endif > > + > > + return 0; > > +} > > +#endif > > + > > +#if defined(CONFIG_MISC_INIT_R) > > +int misc_init_r(void) > > +{ > > +#ifdef CONFIG_FSL_DEVICE_DISABLE > > + device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl)); > > +#endif > > + > > +#ifdef CONFIG_FSL_CAAM > > + return sec_init(); > > +#endif > > +} > > +#endif > > + > > +#if defined(CONFIG_DEEP_SLEEP) > > +void board_sleep_prepare(void) > > +{ > > +#ifdef CONFIG_LAYERSCAPE_NS_ACCESS > > + enable_layerscape_ns_access(); > > +#endif > > +} > > +#endif > > + > > +int ft_board_setup(void *blob, bd_t *bd) > > +{ > > + ft_cpu_setup(blob, bd); > > + > > +#ifdef CONFIG_PCI > > + ft_pci_setup(blob, bd); > > +#endif > > + > > + return 0; > > +} > > diff --git a/board/freescale/ls1021atsn/ls102xa_pbi.cfg > > b/board/freescale/ls1021atsn/ls102xa_pbi.cfg > > new file mode 100644 > > index 000000000000..a8ba184c6684 > > --- /dev/null > > +++ b/board/freescale/ls1021atsn/ls102xa_pbi.cfg > > What is this file? Is it built by something? > Yes, search for CONFIG_SYS_FSL_PBL_PBI in include/configs/ls1021atsn.h and in the main Makefile. So the boot ROM of the SoC searches for a 512-bit wide data structure starting with sector 8 of the MMC called RCW (Reset Configuration Word). This defines PLL frequencies, SerDes protocols, pinmuxing etc on the SoC. The RCW can also have a sequence of PBL (Pre-Boot Loader) commands appended to it - generally these are memory write operations that do stuff such as errata workarounds before the execution transfers to the boot loader. Actually I believe, but can't prove, that it is the PBL who copies the U-Boot SPL from MMC into an internal SRAM called OCRAM (on-chip RAM) before transferring the execution to it. I say I can't prove this because I would have expected to recognize this block copy command in the file you asked about. The takeaway is that for MMC-based booting, the RCW and PBI commands are packaged together in a file called u-boot-with-spl-pbl.bin. For QSPI-based booting that is not the case - the SPL and the OCRAM are not involved because the QSPI flash is memory-mapped so the CPU can execute the U-Boot image directly. In the case of booting from QSPI flash, the RCW and PBL commands are not packaged with the U-Boot image, but instead you're supposed to flash them separately. To be honest I don't know why it is like that - I'm not a big fan of keeping a relatively opaque hex dump of the RCW and PBL commands in U-Boot (let alone that the process is not the same for all boot sources). > > @@ -0,0 +1,15 @@ > > +#PBI commands > > + > > +09570200 ffffffff > > +09570158 00000300 > > +8940007c 21f47300 > > + > > +# Configure Scratch register > > +09ee0200 10000000 > > +# Configure alternate space > > +09570158 00001000 > > +# Flush PBL data > > +096100c0 000FFFFF > > + > > +09ea085c 00502880 > > +09ea0560 80800000 > > diff --git a/board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg > > b/board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg > > new file mode 100644 > > index 000000000000..67152dd2810e > > --- /dev/null > > +++ b/board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg > > @@ -0,0 +1,8 @@ > > +# PBL preamble and RCW header > > +aa55aa55 01ee0100 > > + > > +# Disable IFC, enable QSPI and DSPI > > +0608000c 00000000 00000000 00000000 > > +30000000 08007900 60040a00 21046000 > > +00000000 00000000 00000000 20002000 > > +20024800 8804b340 00000000 00000000 > > diff --git a/configs/ls1021atsn_qspi_defconfig > > b/configs/ls1021atsn_qspi_defconfig > > new file mode 100644 > > index 000000000000..427881fe0c52 > > --- /dev/null > > +++ b/configs/ls1021atsn_qspi_defconfig > > @@ -0,0 +1,76 @@ > > +CONFIG_ARM=y > > +CONFIG_TARGET_LS1021ATSN=y > > +CONFIG_SYS_TEXT_BASE=0x40100000 > > +CONFIG_DEFAULT_DEVICE_TREE="ls1021a-tsn" > > +CONFIG_BOARD_EARLY_INIT_F=y > > +CONFIG_SYS_FSL_CLK=y > > +CONFIG_SYS_EXTRA_OPTIONS="QSPI_BOOT" > > +CONFIG_QSPI_BOOT=y > > +CONFIG_BOOTDELAY=3 > > +CONFIG_HUSH_PARSER=y > > +CONFIG_CMD_GREPENV=y > > +CONFIG_CMD_MEMINFO=y > > +CONFIG_CMD_GPT=y > > +CONFIG_CMD_FAT=y > > +CONFIG_FSL_ESDHC=y > > +CONFIG_CMD_SF=y > > +CONFIG_OF_CONTROL=y > > +CONFIG_ENV_IS_IN_SPI_FLASH=y > > +CONFIG_DM=y > > +CONFIG_FSL_CAAM=y > > +CONFIG_SPI=y > > +CONFIG_SPI_FLASH=y > > +CONFIG_SPI_FLASH_ATMEL=y > > +CONFIG_SPI_FLASH_STMICRO=y > > +CONFIG_SPI_FLASH_BAR=y > > +CONFIG_SPI_FLASH_SPANSION=y > > +CONFIG_NETDEVICES=y > > +CONFIG_DM_ETH=y > > +CONFIG_TSEC_ENET=y > > +CONFIG_MII=y > > +CONFIG_SYS_NS16550=y > > +CONFIG_DM_SPI=y > > +CONFIG_DM_SPI_FLASH=y > > +CONFIG_SPI_FLASH_DATAFLASH=y > > +CONFIG_FSL_DSPI=y > > +CONFIG_FSL_QSPI=y > > +CONFIG_PCI=y > > +CONFIG_CMD_PCI=y > > +CONFIG_DM_PCI=y > > +CONFIG_DM_PCI_COMPAT=y > > +CONFIG_CMD_MMC=y > > +CONFIG_DM_MMC=y > > +CONFIG_FSL_SPI_ALIGNED_TXFIFO=y > > +CONFIG_USB=y > > +CONFIG_DM_USB=y > > +CONFIG_CMD_USB=y > > +CONFIG_USB_XHCI_HCD=y > > +CONFIG_USB_XHCI_FSL=y > > +CONFIG_USB_XHCI_DWC3=y > > +CONFIG_HAS_FSL_XHCI_USB=y > > +CONFIG_USB_STORAGE=y > > +CONFIG_CMD_EXT2=y > > +CONFIG_PCIE_LAYERSCAPE=y > > +CONFIG_PHYLIB=y > > +CONFIG_PHY_GIGE=y > > +CONFIG_PHY_ATHEROS=y > > +CONFIG_PHY_BROADCOM=y > > +CONFIG_PHY_FIXED=y > > +CONFIG_CMD_PING=y > > +CONFIG_CMD_DHCP=y > > +CONFIG_CMD_MII=y > > +CONFIG_CMDLINE_TAG=y > > +CONFIG_CMDLINE_EDITING=y > > +CONFIG_AUTO_COMPLETE=y > > +CONFIG_NR_DRAM_BANKS=1 > > +CONFIG_CMD_BOOTZ=y > > +CONFIG_SYS_LONGHELP=y > > +CONFIG_FIT=y > > +CONFIG_CMD_DM=y > > +CONFIG_AHCI=y > > +CONFIG_CMD_I2C=y > > +CONFIG_BLK=y > > +CONFIG_CMD_PART=y > > +CONFIG_CMD_FS_GENERIC=y > > +CONFIG_CMD_FS_UUID=y > > +CONFIG_DISTRO_DEFAULTS=y > > diff --git a/configs/ls1021atsn_sdcard_defconfig > > b/configs/ls1021atsn_sdcard_defconfig > > new file mode 100644 > > index 000000000000..b74e01206817 > > --- /dev/null > > +++ b/configs/ls1021atsn_sdcard_defconfig > > @@ -0,0 +1,85 @@ > > +CONFIG_ARM=y > > +CONFIG_TARGET_LS1021ATSN=y > > +CONFIG_SPL_TEXT_BASE=0x10000000 > > +CONFIG_SYS_TEXT_BASE=0x82000000 > > +CONFIG_DEFAULT_DEVICE_TREE="ls1021a-tsn" > > +CONFIG_BOARD_EARLY_INIT_F=y > > +CONFIG_SPL=y > > +CONFIG_SPL_FRAMEWORK=y > > +CONFIG_SYS_FSL_CLK=y > > +CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT,SD_BOOT_QSPI" > > +CONFIG_SD_BOOT=y > > +CONFIG_BOOTDELAY=3 > > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y > > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xe8 > > +CONFIG_HUSH_PARSER=y > > +CONFIG_CMD_GREPENV=y > > +CONFIG_CMD_MEMINFO=y > > +CONFIG_CMD_GPT=y > > +CONFIG_CMD_FAT=y > > +CONFIG_CMD_MMC=y > > +CONFIG_FSL_ESDHC=y > > +CONFIG_CMD_SF=y > > +CONFIG_OF_CONTROL=y > > +CONFIG_ENV_IS_IN_MMC=y > > +CONFIG_DM=y > > +CONFIG_FSL_CAAM=y > > +CONFIG_SPI=y > > +CONFIG_SPI_FLASH=y > > +CONFIG_SPI_FLASH_ATMEL=y > > +CONFIG_SPI_FLASH_STMICRO=y > > +CONFIG_SPI_FLASH_BAR=y > > +CONFIG_SPI_FLASH_SPANSION=y > > +CONFIG_NETDEVICES=y > > +CONFIG_DM_ETH=y > > +CONFIG_TSEC_ENET=y > > +CONFIG_MII=y > > +CONFIG_SYS_NS16550=y > > +CONFIG_DM_SPI=y > > +CONFIG_DM_SPI_FLASH=y > > +CONFIG_SPI_FLASH_DATAFLASH=y > > +CONFIG_FSL_DSPI=y > > +CONFIG_FSL_QSPI=y > > +CONFIG_PCI=y > > +CONFIG_CMD_PCI=y > > +CONFIG_DM_PCI=y > > +CONFIG_DM_PCI_COMPAT=y > > +CONFIG_USB=y > > +CONFIG_DM_USB=y > > +CONFIG_CMD_USB=y > > +CONFIG_USB_XHCI_HCD=y > > +CONFIG_USB_XHCI_FSL=y > > +CONFIG_USB_XHCI_DWC3=y > > +CONFIG_HAS_FSL_XHCI_USB=y > > +CONFIG_USB_STORAGE=y > > +CONFIG_CMD_EXT2=y > > +CONFIG_PCIE_LAYERSCAPE=y > > +CONFIG_PHYLIB=y > > +CONFIG_PHY_GIGE=y > > +CONFIG_PHY_ATHEROS=y > > +CONFIG_PHY_BROADCOM=y > > +CONFIG_PHY_FIXED=y > > +CONFIG_CMD_PING=y > > +CONFIG_CMD_DHCP=y > > +CONFIG_CMD_MII=y > > +CONFIG_CMDLINE_TAG=y > > +CONFIG_CMDLINE_EDITING=y > > +CONFIG_AUTO_COMPLETE=y > > +CONFIG_NR_DRAM_BANKS=1 > > +CONFIG_CMD_BOOTZ=y > > +CONFIG_SYS_LONGHELP=y > > +CONFIG_FIT=y > > +CONFIG_SPL_MMC_SUPPORT=y > > +CONFIG_SPL_SERIAL_SUPPORT=y > > +CONFIG_SPL_I2C_SUPPORT=y > > +CONFIG_SPL_ENV_SUPPORT=y > > +CONFIG_SPL_LIBCOMMON_SUPPORT=y > > +CONFIG_CMD_DM=y > > +CONFIG_AHCI=y > > +CONFIG_CMD_I2C=y > > +CONFIG_BLK=y > > +CONFIG_DM_MMC=y > > +CONFIG_CMD_PART=y > > +CONFIG_CMD_FS_GENERIC=y > > +CONFIG_CMD_FS_UUID=y > > +CONFIG_DISTRO_DEFAULTS=y > > diff --git a/include/configs/ls1021atsn.h b/include/configs/ls1021atsn.h > > new file mode 100644 > > index 000000000000..c8ec414afd39 > > --- /dev/null > > +++ b/include/configs/ls1021atsn.h > > @@ -0,0 +1,346 @@ > > +/* SPDX-License-Identifier: GPL-2.0 > > + * Copyright 2016-2018 NXP Semiconductors > > + * Copyright 2019 Vladimir Oltean <olte...@gmail.com> > > + */ > > + > > +#ifndef __CONFIG_H > > +#define __CONFIG_H > > + > > +#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR > > + > > +#define CONFIG_SYS_FSL_CLK > > + > > +#define CONFIG_DEEP_SLEEP > > +#ifdef CONFIG_DEEP_SLEEP > > +#define CONFIG_SILENT_CONSOLE > > +#endif > > + > > +/* > > + * Size of malloc() pool > > + */ > > +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) > > + > > +#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR > > +#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE > > + > > +/* XHCI Support - enabled by default */ > > +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 > > + > > +#define CONFIG_SYS_CLK_FREQ 100000000 > > +#define CONFIG_DDR_CLK_FREQ 100000000 > > + > > +#define DDR_SDRAM_CFG 0x470c0008 > > +#define DDR_CS0_BNDS 0x008000bf > > +#define DDR_CS0_CONFIG 0x80014302 > > +#define DDR_TIMING_CFG_0 0x50550004 > > +#define DDR_TIMING_CFG_1 0xbcb38c56 > > +#define DDR_TIMING_CFG_2 0x0040d120 > > +#define DDR_TIMING_CFG_3 0x010e1000 > > +#define DDR_TIMING_CFG_4 0x00000001 > > +#define DDR_TIMING_CFG_5 0x03401400 > > +#define DDR_SDRAM_CFG_2 0x00401010 > > +#define DDR_SDRAM_MODE 0x00061c60 > > +#define DDR_SDRAM_MODE_2 0x00180000 > > +#define DDR_SDRAM_INTERVAL 0x18600618 > > +#define DDR_DDR_WRLVL_CNTL 0x8655f605 > > +#define DDR_DDR_WRLVL_CNTL_2 0x05060607 > > +#define DDR_DDR_WRLVL_CNTL_3 0x05050505 > > +#define DDR_DDR_CDR1 0x80040000 > > +#define DDR_DDR_CDR2 0x00000001 > > +#define DDR_SDRAM_CLK_CNTL 0x02000000 > > +#define DDR_DDR_ZQ_CNTL 0x89080600 > > +#define DDR_CS0_CONFIG_2 0 > > +#define DDR_SDRAM_CFG_MEM_EN 0x80000000 > > +#define SDRAM_CFG2_D_INIT 0x00000010 > > +#define DDR_CDR2_VREF_TRAIN_EN 0x00000080 > > +#define SDRAM_CFG2_FRC_SR 0x80000000 > > +#define SDRAM_CFG_BI 0x00000001 > > + > > +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 > > + > > +#ifdef CONFIG_RAMBOOT_PBL > > +#define CONFIG_SYS_FSL_PBL_PBI \ > > + "board/freescale/ls1021atsn/ls102xa_pbi.cfg" > > +#endif > > + > > +#ifdef CONFIG_SD_BOOT > > +#ifdef CONFIG_SD_BOOT_QSPI > > +#define CONFIG_SYS_FSL_PBL_RCW \ > > + "board/freescale/ls1021atsn/ls102xa_rcw_sd_qspi.cfg" > > +#else > > +#define CONFIG_SYS_FSL_PBL_RCW \ > > + "board/freescale/ls1021atsn/ls102xa_rcw_sd_ifc.cfg" > > +#endif > > +#define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds" > > +#define CONFIG_SPL_LIBGENERIC_SUPPORT > > +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT > > +#define CONFIG_SPL_WATCHDOG_SUPPORT > > +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xe8 > > + > > +#ifdef CONFIG_SECURE_BOOT > > +#define CONFIG_U_BOOT_HDR_SIZE (16 << 10) > > +#endif /* ifdef CONFIG_SECURE_BOOT */ > > + > > +#define CONFIG_SPL_MAX_SIZE 0x1a000 > > +#define CONFIG_SPL_STACK 0x1001d000 > > +#define CONFIG_SPL_PAD_TO 0x1c000 > > + > > +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ > > + CONFIG_SYS_MONITOR_LEN) > > +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 > > +#define CONFIG_SPL_BSS_START_ADDR 0x80100000 > > +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 > > + > > +#ifdef CONFIG_U_BOOT_HDR_SIZE > > +/* > > + * HDR would be appended at end of image and copied to DDR along > > + * with U-Boot image. Here u-boot max. size is 512K. So if binary > > U-Boot (second one). > > > + * size increases then increase this size in case of secure boot as > > + * it uses raw u-boot image instead of fit image. > > U-Boot > > > + */ > > +#define CONFIG_SYS_MONITOR_LEN (0x80000 + CONFIG_U_BOOT_HDR_SIZE) > > +#else > > +#define CONFIG_SYS_MONITOR_LEN 0x80000 > > +#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */ > > +#endif > > + > > +#define CONFIG_NR_DRAM_BANKS 1 > > +#define PHYS_SDRAM 0x80000000 > > +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) > > + > > +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL > > +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE > > + > > +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 > > + > > +#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \ > > + !defined(CONFIG_QSPI_BOOT) > > +#define CONFIG_U_QE > > +#endif > > + > > +/* > > + * IFC Definitions > > + */ > > +#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) > > +#define CONFIG_FSL_IFC > > +#endif > > + > > +/* CPLD */ > > +#define CONFIG_SYS_CPLD_BASE 0x7fb00000 > > +#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE > > + > > +#define CONFIG_SYS_FPGA_CSPR_EXT (0x0) > > +#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \ > > + CSPR_PORT_SIZE_8 | \ > > + CSPR_MSEL_GPCM | \ > > + CSPR_V) > > +#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) > > +#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ > > + CSOR_NOR_NOR_MODE_AVD_NOR | \ > > + CSOR_NOR_TRHZ_80) > > + > > +/* CPLD Timing parameters for IFC GPCM */ > > +#define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \ > > + FTIM0_GPCM_TEADC(0xf) | \ > > + FTIM0_GPCM_TEAHC(0xf)) > > +#define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ > > + FTIM1_GPCM_TRAD(0x3f)) > > +#define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ > > + FTIM2_GPCM_TCH(0xf) | \ > > + FTIM2_GPCM_TWP(0xff)) > > +#define CONFIG_SYS_FPGA_FTIM3 0x0 > > +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_FPGA_CSPR_EXT > > +#define CONFIG_SYS_CSPR0 CONFIG_SYS_FPGA_CSPR > > +#define CONFIG_SYS_AMASK0 CONFIG_SYS_FPGA_AMASK > > +#define CONFIG_SYS_CSOR0 CONFIG_SYS_FPGA_CSOR > > +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_FPGA_FTIM0 > > +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_FPGA_FTIM1 > > +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_FPGA_FTIM2 > > +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_FPGA_FTIM3 > > + > > +/* > > + * Serial Port > > + */ > > +#define CONFIG_CONS_INDEX 1 > > +#define CONFIG_SYS_NS16550_SERIAL > > +#ifndef CONFIG_DM_SERIAL > > +#define CONFIG_SYS_NS16550_REG_SIZE 1 > > +#endif > > +#define CONFIG_SYS_NS16550_CLK get_serial_clock() > > + > > +#define CONFIG_BAUDRATE 115200 > > + > > +/* > > + * I2C > > + */ > > +#define CONFIG_SYS_I2C > > +#define CONFIG_SYS_I2C_MXC > > +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ > > +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ > > +#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ > > + > > +/* EEPROM */ > > +#define CONFIG_ID_EEPROM > > +#define CONFIG_SYS_I2C_EEPROM_NXID > > +#define CONFIG_SYS_EEPROM_BUS_NUM 0 > > +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51 > > +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 > > + > > +/* SPI */ > > +#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) > > +/* QSPI */ > > +#define FSL_QSPI_FLASH_SIZE (1 << 24) > > +#define FSL_QSPI_FLASH_NUM 2 > > +/* DSPI */ > > +#endif > > + > > +#ifdef CONFIG_TSEC_ENET > > +#define CONFIG_ETHPRIME "ethernet@2d10000" > > Where does this name come from? Is this not the first mac, i.e. would > you get this without the explicit setting ethprime? > I don't know, I didn't try not setting this. It is the first MAC, yes. > > +#endif > > + > > +/* PCIe */ > > +#define CONFIG_PCIE1 /* PCIE controller 1 */ > > +#define CONFIG_PCIE2 /* PCIE controller 2 */ > > +#define FSL_PCIE_COMPAT "fsl,ls1021a-pcie" > > +#ifdef CONFIG_PCI > > +#define CONFIG_PCI_SCAN_SHOW > > +#endif > > + > > +#define CONFIG_PEN_ADDR_BIG_ENDIAN > > +#define CONFIG_LAYERSCAPE_NS_ACCESS > > +#define CONFIG_SMP_PEN_ADDR 0x01ee0200 > > +#define COUNTER_FREQUENCY 12500000 > > + > > +#define CONFIG_HWCONFIG > > +#define HWCONFIG_BUFFER_SIZE 256 > > + > > +#define CONFIG_FSL_DEVICE_DISABLE > > + > > +#define BOOT_TARGET_DEVICES(func) \ > > + func(MMC, mmc, 0) \ > > + func(USB, usb, 0) \ > > + func(DHCP, dhcp, na) > > +#include <config_distro_bootcmd.h> > > + > > +#define CONFIG_EXTRA_ENV_SETTINGS \ > > + "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ > > + "initrd_high=0xffffffff\0" \ > > + "fdt_high=0xffffffff\0" \ > > + "fdt_addr=0x64f00000\0" \ > > + "kernel_addr=0x61000000\0" \ > > + "kernelheader_addr=0x60800000\0" \ > > + "scriptaddr=0x80000000\0" \ > > + "scripthdraddr=0x80080000\0" \ > > + "fdtheader_addr_r=0x80100000\0" \ > > + "kernelheader_addr_r=0x80200000\0" \ > > + "kernel_addr_r=0x80008000\0" \ > > + "kernelheader_size=0x40000\0" \ > > + "fdt_addr_r=0x8f000000\0" \ > > + "ramdisk_addr_r=0xa0000000\0" \ > > + "load_addr=0x80008000\0" \ > > + "kernel_size=0x2800000\0" \ > > + "kernel_addr_sd=0x8000\0" \ > > + "kernel_size_sd=0x14000\0" \ > > + "kernelhdr_addr_sd=0x4000\0" \ > > + "kernelhdr_size_sd=0x10\0" \ > > + BOOTENV \ > > + "boot_scripts=ls1021atsn_boot.scr\0" \ > > + "boot_script_hdr=hdr_ls1021atsn_bs.out\0" \ > > + "scan_dev_for_boot_part=" \ > > + "part list ${devtype} ${devnum} devplist; " \ > > + "env exists devplist || setenv devplist 1; " \ > > + "for distro_bootpart in ${devplist}; do " \ > > + "if fstype ${devtype} " \ > > + "${devnum}:${distro_bootpart} " \ > > + "bootfstype; then " \ > > + "run scan_dev_for_boot; " \ > > + "fi; " \ > > + "done\0" \ > > + "scan_dev_for_boot=" \ > > + "echo Scanning ${devtype} " \ > > + "${devnum}:${distro_bootpart}...; " \ > > + "for prefix in ${boot_prefixes}; do " \ > > + "run scan_dev_for_scripts; " \ > > + "run scan_dev_for_extlinux; " \ > > + "done;" \ > > + "\0" \ > > + "boot_a_script=" \ > > + "load ${devtype} ${devnum}:${distro_bootpart} " \ > > + "${scriptaddr} ${prefix}${script}; " \ > > + "env exists secureboot && load ${devtype} " \ > > + "${devnum}:${distro_bootpart} " \ > > + "${scripthdraddr} ${prefix}${boot_script_hdr} " \ > > + "&& esbc_validate ${scripthdraddr};" \ > > + "source ${scriptaddr}\0" \ > > + "qspi_bootcmd=echo Trying load from qspi..;" \ > > + "sf probe && sf read $load_addr " \ > > + "$kernel_addr $kernel_size; env exists secureboot " \ > > + "&& sf read $kernelheader_addr_r $kernelheader_addr " \ > > + "$kernelheader_size && esbc_validate > > ${kernelheader_addr_r}; " \ > > + "bootm $load_addr#$board\0" \ > > + "sd_bootcmd=echo Trying load from SD ..;" \ > > + "mmcinfo && mmc read $load_addr " \ > > + "$kernel_addr_sd $kernel_size_sd && " \ > > + "env exists secureboot && mmc read $kernelheader_addr_r " \ > > + "$kernelhdr_addr_sd $kernelhdr_size_sd " \ > > + " && esbc_validate ${kernelheader_addr_r};" \ > > + "bootm $load_addr#$board\0" > > + > > +#undef CONFIG_BOOTCOMMAND > > +#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) > > +#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \ > > + "env exists secureboot && esbc_halt" > > +#elif defined(CONFIG_SD_BOOT) > > +#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; " \ > > + "env exists secureboot && esbc_halt;" > > +#endif > > + > > +/* > > + * Miscellaneous configurable options > > + */ > > +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size > > */ > > +#define CONFIG_SYS_PBSIZE \ > > + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) > > +#define CONFIG_SYS_MAXARGS 16 /* max number of command > > args */ > > +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE > > + > > +#define CONFIG_SYS_LOAD_ADDR 0x82000000 > > + > > +#define CONFIG_LS102XA_STREAM_ID > > + > > +#define CONFIG_SYS_INIT_SP_OFFSET \ > > + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) > > +#define CONFIG_SYS_INIT_SP_ADDR \ > > + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) > > + > > +#ifdef CONFIG_SPL_BUILD > > +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE > > +#else > > +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of > > monitor */ > > +#endif > > + > > +#define CONFIG_SYS_QE_FW_ADDR 0x67f40000 > > + > > +/* > > + * Environment > > + */ > > +#define CONFIG_ENV_OVERWRITE > > + > > +#if defined(CONFIG_SD_BOOT) > > +#define CONFIG_ENV_OFFSET 0x300000 > > +#define CONFIG_SYS_MMC_ENV_DEV 0 > > +#define CONFIG_ENV_SIZE 0x20000 > > +#elif defined(CONFIG_QSPI_BOOT) > > +#define CONFIG_ENV_SIZE 0x2000 > > +#define CONFIG_ENV_OFFSET 0x300000 > > +#define CONFIG_ENV_SECT_SIZE 0x40000 > > +#endif > > + > > +#define CONFIG_OF_BOARD_SETUP > > +#define CONFIG_OF_STDOUT_VIA_ALIAS > > +#define CONFIG_MISC_INIT_R > > + > > +#include <asm/fsl_secure_boot.h> > > +#define CONFIG_SYS_BOOTM_LEN 0x8000000 /* 128 MB */ > > + > > +#endif > > -- > > 2.17.1 > > > > _______________________________________________ > > U-Boot mailing list > > U-Boot@lists.denx.de > > https://lists.denx.de/listinfo/u-boot Thanks, -Vladimir _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot