On Tue, Oct 29, 2019 at 2:08 PM Suneel Garapati <suneelgli...@gmail.com> wrote:
> This series will add support for OcteonTX and OcteonTX2 processsor based
> platforms. The Marvell/Cavium Octeon-TX 64-bit ARM based SoCs include
> the CN80XX, CN81XX and CN83XX while Octeon-TX2 64-bit ARM based SoCs include
> support for CN96XX and CN95XX.
> These SoC's have peripheral drivers based on PCI ECAM.
> Patches
> [1 -10] Add requied changes to PCI framework
>  - [6] Add support for multi-memory region range
>  - [7] EA in bridges
>  - [8] SR-IOV
> [12] Add driver model support for RTC DS1337 driver
> [15 - 17] AHCI changes
> [18 - 27] Add OcteonTX drivers
> [28 - 29] Add OcteonTX/TX2 board files and configurations


Thanks for submitting this series!

I've applied and built this and am testing on the Gateworks Newport
boards with the CN802x/CN803x (octeontx_81xx) and this is what I've
- I get hung in the smc_call from smc_dram_size which your calling
with the function id of 0xc2000301. The older U-Boot from the Cavium
OcteonTX SDK-6.2.0-p3 used 0x43000301 and this works for me. Is there
a difference in our ATF version?
- configs/octeontx_81xx_defconfig - I have several changes I want to
make here, but perhaps some of these would warrant a custom config for
my boards
  - you assume there is only a SPI NOR flash for env which we
personally don't use. The env system supports multiple env types so we
could just enable MMC as well as SPI but then I find all the
hard-coded CONFIG_ENV_* defines restrictive. I wonder if anyone has
defined a way for these to come from device-tree?
  - you set loadaddr=040080000 which only makes sense for systems with
over 1GiB of DRAM... perhaps we should lower that to
loadaddr=020080000 for 1GiB systems (I don't think you can have less
than 1GiB?)
  - I use DISTRO_DEFAULTS for a standard distro-friendly boot env...
I'm not sure why any board wouldn't do this these days and I think
that should be added

I was able to functionally test mmc/i2c/gpio/pci/nic(BGX/RGX) and they
were all functioning well.

When I enable SATA I find that it crashes on init:
GW6300-D1> sata info
Target spinup took 0 ms.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: 64bit ncq ilck stag pm led clo only pmp fbss pio slum part ccc apst
"Synchronous Abort" handler, esr 0x96000006
elr: 000000000052c240 lr : 00000000005101bc (reloc)
elr: 000000003fecb240 lr : 000000003feaf1bc
x0 : 000000003be91380 x1 : 0000000000000000
x2 : 0000000000000000 x3 : 000000003be9c100
x4 : 0000000000000120 x5 : 000000003be9b800
x6 : 0000000000000001 x7 : 0000000000000000
x8 : 000000003ff46998 x9 : 0000000000000008
x10: 000000003ff2e8c4 x11: 000000003ff2e8ca
x12: 000000003ff2e8cf x13: 000000003ff2e8d5
x14: 000000003ff2e8da x15: 000000003ff2e8e0
x16: 000000003ff2e8e6 x17: 000000003ff43362
x18: 000000003be8ede0 x19: 0000000000000000
x20: 000000003be9ab30 x21: 0000000000000002
x22: 000000003be9ab30 x23: 0000000000000002
x24: 000000003ff63aa4 x25: 000000003be9ab90
x26: 0000000000000000 x27: 0000000000000000
x28: 0000000000000000 x29: 000000003be881f0

Code: 928004a0 d65f03c0 f9400007 f94034e7 (f94008e7)
Resetting CPU ...

I don't have NAND or SPI flash so can't test those.

Best Regards,

U-Boot mailing list

Reply via email to