[U-Boot] [PATCH 6/7] mmc: fsl_esdhc: always check write protect state

[Yangbo Lu]

The QorIQ eSDHC on all platforms supports checking write protect
state through register bit. So check it always.

Signed-off-by: Yangbo Lu <yangbo...@nxp.com>
---
 drivers/mmc/fsl_esdhc.c | 15 ++++-----------
 include/fsl_esdhc.h     |  1 -
 2 files changed, 4 insertions(+), 12 deletions(-)

diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index 25a8fe3..bdc0ca6 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -75,7 +75,6 @@ struct fsl_esdhc_plat {
  * @mmc: mmc
  * Following is used when Driver Model is enabled for MMC
  * @dev: pointer for the device
- * @wp_enable: 1: enable checking wp; 0: no check
  * @cd_gpio: gpio for card detection
  * @wp_gpio: gpio for write protection
  */
@@ -88,7 +87,6 @@ struct fsl_esdhc_priv {
        struct mmc *mmc;
 #endif
        struct udevice *dev;
-       int wp_enable;
 };
 
 /* Return the XFERTYP flags for a given command and data packet */
@@ -231,12 +229,10 @@ static int esdhc_setup_data(struct fsl_esdhc_priv *priv, 
struct mmc *mmc,
 #endif
                if (wml_value > WML_WR_WML_MAX)
                        wml_value = WML_WR_WML_MAX_VAL;
-               if (priv->wp_enable) {
-                       if ((esdhc_read32(&regs->prsstat) &
-                           PRSSTAT_WPSPL) == 0) {
-                               printf("\nThe SD card is locked. Can not write 
to a locked card.\n\n");
-                               return -ETIMEDOUT;
-                       }
+
+               if (!(esdhc_read32(&regs->prsstat) & PRSSTAT_WPSPL)) {
+                       printf("Can not write to locked SD card.\n");
+                       return -EINVAL;
                }
 
                esdhc_clrsetbits32(&regs->wml, WML_WR_WML_MASK,
@@ -722,7 +718,6 @@ int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg 
*cfg)
 
        priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base);
        priv->sdhc_clk = cfg->sdhc_clk;
-       priv->wp_enable  = cfg->wp_enable;
 
        mmc_cfg = &plat->cfg;
 
@@ -862,8 +857,6 @@ static int fsl_esdhc_probe(struct udevice *dev)
 #endif
        priv->dev = dev;
 
-       priv->wp_enable = 1;
-
        if (IS_ENABLED(CONFIG_CLK)) {
                /* Assigned clock already set clock */
                ret = clk_get_by_name(dev, "per", &priv->per_clk);
diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h
index a015df1..8e8cd2c 100644
--- a/include/fsl_esdhc.h
+++ b/include/fsl_esdhc.h
@@ -168,7 +168,6 @@ struct fsl_esdhc_cfg {
        phys_addr_t esdhc_base;
        u32     sdhc_clk;
        u8      max_bus_width;
-       int     wp_enable;
        int     vs18_enable; /* Use 1.8V if set to 1 */
        struct mmc_config cfg;
 };
-- 
2.7.4

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot