On 11/20/2019 10:51 AM, Grygorii Strashko wrote:
On 19/11/2019 20:58, Grygorii Strashko wrote:
On 19/11/2019 01:31, Alexandru Marginean wrote:
On 11/18/2019 8:11 PM, Grygorii Strashko wrote:
On 14/11/2019 17:04, Alex Marginean wrote:
Adds an optional mdio-handle property which identifies a MDIO bus
which can
be scanned to find the relevant PHY. The property is ignored if
phy-handle
is also present.
Signed-off-by: Alex Marginean <alexandru.margin...@nxp.com>
---
doc/device-tree-bindings/net/ethernet.txt | 2 ++
1 file changed, 2 insertions(+)
diff --git a/doc/device-tree-bindings/net/ethernet.txt
b/doc/device-tree-bindings/net/ethernet.txt
index 3fc360523b..9f9629f8d6 100644
--- a/doc/device-tree-bindings/net/ethernet.txt
+++ b/doc/device-tree-bindings/net/ethernet.txt
@@ -9,6 +9,8 @@ The following properties are common to the Ethernet
controllers:
- max-speed: number, specifies maximum speed in Mbit/s supported
by the device;
- max-frame-size: number, maximum transfer unit (IEEE defined
MTU), rather than
the maximum frame size (there's contradiction in ePAPR).
+- mdio-handle: phandle, specifies a reference to a MDIO bus to be
scanned to
+ find the PHY device. Ignored if phy-handle is also present.
Sry, but it looks redundant. The Ethernet-controller bindings
expects to use phy-handle which, in turn, allows to get MDIO node.
The problem I'm trying to solve is not that I don't want to get the
parent MDIO bus of a PHY referenced though phy-handle, but rather that I
want to avoid having a specific U-Boot DT for each PHY plug-in card that
could be used in our systems. I'll explain that in more detail.
We have these QDS systems which support plug-in cards with PHYs on them.
The way it works is that a given ethernet interface is associated with
one of the QDS slots that should contain a plug-in card. Each of the
slots has a MDIO bus associated with it, this bus is accessed through a
MDIO MUX on the QDS board.
The slot may be populated with one of several types of cards, which
are different designs, have different types of PHYs and more importantly
use different PHY addresses on the MDIO bus.
So now the summary is that an Ethernet interface is associated with a
MDIO bus that could be scanned to find the relevant PHY, while using the
existing phy-handle binding requires that U-Boot DT is edited whenever
a different card is plugged in, which is not practical and avoidable.
Thank you for explanation. It's clear now.
I think above description is good to have as part of commit message.
So, if your platform is DT based and can use DT then it's reasonable
to follow standard binding,
which, in addition, allows to specify Ethernet PHY properties.
Sure, and we do that on boards and for PHYs which are at fixed addresses
on MDIO bus, but that is impractical with the swappable cards.
Some thought, which i think might help.
- u-boot allows phy node not to have "reg" property.
- phy_connect() will return first PHY discovered on the MDIO bus if addr<=0
So, if MDIO assignment per ethernet interface/slot is fixed DT can look
like
mdioX {
mdiox_phy0: ethernet-phy@0 {
};
}
ethernetX {
phy-handle = <&mdiox_phy0>;
}
and so on. driver's parsing code can ignore PHY "reg" prop in phy
node and pass addr<=0 to phy_connect().
Functionally that's what I'm looking for, yes. There is the problem of
not strictly following the kernel binding and at the end of the day I
will have the same problem with the kernel too, so I should take this
topic to the netdev list anyway.
Having 'reg' made optional is actually an interesting idea. I think
'mdio-handle' is a bit more clear what it is, but having an actual PHY
node allows passing DT properties on to the PHY driver which is
certainly useful for some PHYs. It's like saying I don't know what PHY
I'm going to find, but if it's a PHY that has these configurable
properties here is your configuration.
It seems, current Linux approach is to have PHY "reg" property as
required, but your case might be the reason to change this. >
I'll have to do a better write-up for the kernel list and we'll see
how this will go.
In the meantime any feedback on the other patches, except the one
introducing mdio-handle? For instance I should deal with fixed links
in the dm_eth_phy_connect helper too (calling phy_connect_fixed),
my intent is to take some code that is otherwise pretty generic out of
the drivers.
Thanks!
Alex
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
