Currently the following SPL hang is observed:
U-Boot SPL 2020.01-rc5-00079-g797eee36a1 (Jan 06 2020 - 11:24:09 -0300)
Trying to boot from MMC1
Card did not respond to voltage select!
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix it by moving the eSDHC1 initialization to SPL.
While at it, since this board uses DM_MMC all the esdhc board
code can be removed.
Signed-off-by: Fabio Estevam <feste...@gmail.com>
---
Hi,
Still get the following "no card present" error in U-Boot proper:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
but this should be treated separately.
.../mx6ul_14x14_evk/mx6ul_14x14_evk.c | 175 ++----------------
1 file changed, 20 insertions(+), 155 deletions(-)
diff --git a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
index 898da34729..086e0e6739 100644
--- a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
+++ b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
@@ -36,14 +36,6 @@ DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_DAT3_CD_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
@@ -112,67 +104,6 @@ static iomux_v3_cfg_t const uart1_pads[] = {
MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
-static iomux_v3_cfg_t const usdhc1_pads[] = {
- MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-
- /* VSELECT */
- MX6_PAD_GPIO1_IO05__USDHC1_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- /* CD */
- MX6_PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* RST_B */
- MX6_PAD_GPIO1_IO09__GPIO1_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-/*
- * mx6ul_14x14_evk board default supports sd card. If want to use
- * EMMC, need to do board rework for sd2.
- * Introduce CONFIG_MX6UL_14X14_EVK_EMMC_REWORK, if sd2 reworked to support
- * emmc, need to define this macro.
- */
-#if defined(CONFIG_MX6UL_14X14_EVK_EMMC_REWORK)
-static iomux_v3_cfg_t const usdhc2_emmc_pads[] = {
- MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-
- /*
- * RST_B
- */
- MX6_PAD_NAND_ALE__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-#else
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
-/*
- * The evk board uses DAT3 to detect CD card plugin,
- * in u-boot we mux the pin to GPIO when doing board_mmc_getcd.
- */
-static iomux_v3_cfg_t const usdhc2_cd_pad =
- MX6_PAD_NAND_DATA03__GPIO4_IO05 | MUX_PAD_CTRL(USDHC_DAT3_CD_PAD_CTRL);
-
-static iomux_v3_cfg_t const usdhc2_dat3_pad =
- MX6_PAD_NAND_DATA03__USDHC2_DATA3 |
- MUX_PAD_CTRL(USDHC_DAT3_CD_PAD_CTRL);
-#endif
static void setup_iomux_uart(void)
{
@@ -189,101 +120,35 @@ static int board_qspi_init(void)
}
#endif
-#ifdef CONFIG_FSL_ESDHC_IMX
-static struct fsl_esdhc_cfg usdhc_cfg[2] = {
- {USDHC1_BASE_ADDR, 0, 4},
-#if defined(CONFIG_MX6UL_14X14_EVK_EMMC_REWORK)
- {USDHC2_BASE_ADDR, 0, 8},
-#else
- {USDHC2_BASE_ADDR, 0, 4},
-#endif
+#ifdef CONFIG_SPL_BUILD
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
-#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 19)
-#define USDHC1_PWR_GPIO IMX_GPIO_NR(1, 9)
-#define USDHC2_CD_GPIO IMX_GPIO_NR(4, 5)
-#define USDHC2_PWR_GPIO IMX_GPIO_NR(4, 10)
+static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+ {USDHC2_BASE_ADDR, 0, 4},
+};
int board_mmc_getcd(struct mmc *mmc)
{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC1_BASE_ADDR:
- ret = !gpio_get_value(USDHC1_CD_GPIO);
- break;
- case USDHC2_BASE_ADDR:
-#if defined(CONFIG_MX6UL_14X14_EVK_EMMC_REWORK)
- ret = 1;
-#else
- imx_iomux_v3_setup_pad(usdhc2_cd_pad);
- gpio_request(USDHC2_CD_GPIO, "usdhc2 cd");
- gpio_direction_input(USDHC2_CD_GPIO);
-
- /*
- * Since it is the DAT3 pin, this pin is pulled to
- * low voltage if no card
- */
- ret = gpio_get_value(USDHC2_CD_GPIO);
-
- imx_iomux_v3_setup_pad(usdhc2_dat3_pad);
-#endif
- break;
- }
-
- return ret;
+ return 1;
}
int board_mmc_init(bd_t *bis)
{
- int i, ret;
-
- /*
- * According to the board_mmc_init() the following map is done:
- * (U-Boot device node) (Physical Port)
- * mmc0 USDHC1
- * mmc1 USDHC2
- */
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
- gpio_request(USDHC1_CD_GPIO, "usdhc1 cd");
- gpio_direction_input(USDHC1_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-
- gpio_direction_output(USDHC1_PWR_GPIO, 0);
- udelay(500);
- gpio_direction_output(USDHC1_PWR_GPIO, 1);
- break;
- case 1:
-#if defined(CONFIG_MX6UL_14X14_EVK_EMMC_REWORK)
- imx_iomux_v3_setup_multiple_pads(
- usdhc2_emmc_pads, ARRAY_SIZE(usdhc2_emmc_pads));
-#else
- imx_iomux_v3_setup_multiple_pads(
- usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-#endif
- gpio_request(USDHC2_PWR_GPIO, "usdhc2 pwr");
- gpio_direction_output(USDHC2_PWR_GPIO, 0);
- udelay(500);
- gpio_direction_output(USDHC2_PWR_GPIO, 1);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- break;
- default:
- printf("Warning: you configured more USDHC controllers
(%d) than supported by the board\n", i + 1);
- return -EINVAL;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret) {
- printf("Warning: failed to initialize mmc dev
%d\n", i);
- return ret;
- }
- }
- return 0;
+ imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
}
#endif
--
2.17.1
