Hi Fabio, On Tue, 7 Jan 2020 14:54:55 -0300 Fabio Estevam [email protected] wrote:
> Hi Anatolij, > > On Tue, Oct 22, 2019 at 5:35 AM Anatolij Gustschin <[email protected]> wrote: > > > > Add support for i.MX8X based Capricorn Giedi SoM. > > > > Supported interfaces: GPIO, ENET, eMMC, I2C, UART. > > > > Console output: > > > > U-Boot SPL 2019.10-00178-g6e34009eee (Oct 21 2019 - 18:16:42 +0200) > > Trying to boot from MMC1 > > Load image from MMC/SD 0x3e000 > > > > U-Boot 2019.10-00178-g6e34009eee (Oct 21 2019 - 18:16:42 +0200) ##v01.07 > > > > CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 24C > > > > Model: Siemens Giedi > > Board: Capricorn > > Build: SCFW 65afe5f6, SECO-FW 9d71fd5b, ATF d6451cc > > Boot: MMC0 > > DRAM: 1022 MiB > > MMC: FSL_SDHC: 0 > > Loading Environment from MMC... OK > > In: serial@5a080000 > > Out: serial@5a080000 > > Err: serial@5a080000 > > Net: eth1: ethernet@5b050000 [PRIME] > > Autobooting in 1 seconds, press "<Esc><Esc>" to stop > > > > Signed-off-by: Anatolij Gustschin <[email protected]> > > I am getting a hang on my i.MX8QXP MEK with mainline even if applying > your I2C ipg clock patches: > > U-Boot SPL 2020.01-00169-g7f2ff3059d-dirty (Jan 07 2020 - 14:50:41 -0300) > Normal Boot > WDT: Not found! > Trying to boot from MMC2_2 > Load image from MMC/SD 0x46c00 > > > U-Boot 2020.01-00169-g7f2ff3059d-dirty (Jan 07 2020 - 14:50:41 -0300) > > CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 31C > > Model: Freescale i.MX8QXP MEK > Board: iMX8QXP MEK > Boot: SD1 > DRAM: 3 GiB > MMC: FSL_SDHC: 0, FSL_SDHC: 1 > Loading Environment from MMC... *** Warning - bad CRC, using default > environment > > In: serial@5a060000 > Out: serial@5a060000 > Err: serial@5a060000 > Net: > Error: ethernet@5b040000 address not set. > > (It hangs here) > > Where did you get the AT-F, imx-sc-firmware, imx-seco from? I got them from i.MX8QXP Capricorn SoM vendor, here the SCFW blob is very old. I don't have more details about ATF and imx-seco currently. While my tests with v2020.01 release I've commented out the build_info() call in checkboard(), because otherwise the board hangs in build_info() with my current SCFW blob. > I used these components from 4.19.35 NXP BSP release. Did you disable the build_info(), too? It seems so, I don't see build hashes in your boot log. Maybe it hangs while getting MAC address from fuses? Could you comment out the for loop in imx_get_mac_from_fuse() with sc_misc_otp_fuse_read() calls in arch/arm/mach-imx/imx8/cpu.c and return some random MAC address there for a quick test? Thanks, Anatolij
