Hi Mauro, On 20.01.20 10:14, Mauro Condarelli wrote:
SUCCESS!!!
Uffff. ;)
=> usb start; load usb 0:1 85000000 u-boot-mtmips.bin starting USB... Bus ehci@101c0000: pinctrl_select_state_full('ehci@101c0000', 'default'): USB EHCI 1.00 scanning bus ehci@101c0000 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 213156 bytes read in 11 ms (18.5 MiB/s) => sf probe; sf update ${fileaddr} 0 ${filesize} pinctrl_select_state_full('spi@b00', 'default'): SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB device 0 offset 0x0, size 0x340a4 213156 bytes written, 0 bytes skipped in 5.465s, speed 39918 B/s => sf read 86000000 0 ${filesize}; cmp 86000000 ${fileaddr} ${filesize} device 0 offset 0x0, size 0x340a4 SF: 213156 bytes @ 0x0 Read: OK word at 0x860340a4 (0x2e220918) != word at 0x850340a4 (0x1ab4834a) Total of 53289 word(s) were the same => reset resetting ... pinctrl_select_state_full('syscon-reboot', 'default'): pinctrl_select_state_full('system-controller@0', 'default'): U-Boot SPL 2020.01-00643-g1262a953f1 (Jan 20 2020 - 09:33:36 +0100) Trying to boot from NOR U-Boot 2020.01-00643-g1262a953f1 (Jan 20 2020 - 09:33:36 +0100) CPU: MediaTek MT7628A ver:1 eco:2 Boot: DDR2, SPI-NOR 3-Byte Addr, CPU clock from XTAL Clock: CPU: 580MHz, Bus: 193MHz, XTAL: 40MHz Model: LinkIt-Smart-7688 DRAM: 128 MiB Loading Environment from SPI Flash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment Net: Warning: eth@10110000 (eth0) using random MAC address - 72:2c:95:10:90:e9 eth0: eth@10110000 =>*** THANKS!! *** now I need to be able to duplicate this and, if needed, to modify. I tried using last Weijie patch-set, but I got the same error You reported, I "fixed" it removing `obj-y += time.o` from `arch/mips/cpu/Makefile`, but I was afraid to test results ;) What is the right sequence to get Your results? Note: I will need to have also working MMC/SD; in stock U-Boot I had to backport some drivers for that; is it supposed to work out-of-the-box (given right config, of course) in this version?
I've already attached the defconfig file you should use as a base for your VoCore2 port in my last mail. Please find it attached again. Other than that you need to apply all 21 patches of Weijie's latest patchset and this one: https://patchwork.ozlabs.org/patch/1215073/ Then start changing the configuration to your needs - port to the VoCore2 with its changes (MMC, SD etc). Most of this can be done by using the RAM version now (again). There is no additional RAM booting target now any more. You can use the normal U-Boot image for this now. Please note the changes TEXT_BASE here. Its now 0x80200000. HTH. Thanks, Stefan
CONFIG_MIPS=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_SECT_SIZE=0x10000 CONFIG_ENV_OFFSET=0x80000 CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_SYS_MALLOC_F_LEN=0x20000 CONFIG_NR_DRAM_BANKS=1 CONFIG_SPL=y CONFIG_ARCH_MTMIPS=y CONFIG_BOARD_LINKIT_SMART_7688=y CONFIG_SPL_UART2_SPIS_PINMUX=y CONFIG_RESTORE_EXCEPTION_VECTOR_BASE=y # CONFIG_MIPS_BOOT_ENV_LEGACY is not set CONFIG_MIPS_BOOT_FDT=y CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_LEGACY_IMAGE_FORMAT=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_HUSH_PARSER=y CONFIG_CMD_LICENSE=y # CONFIG_CMD_ELF is not set # CONFIG_CMD_XIMG is not set # CONFIG_CMD_CRC32 is not set CONFIG_CMD_MEMINFO=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPIO=y # CONFIG_CMD_LOADS is not set CONFIG_CMD_MTD=y CONFIG_CMD_PART=y CONFIG_CMD_SPI=y CONFIG_CMD_USB=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_TIME=y CONFIG_CMD_FS_GENERIC=y # CONFIG_DOS_PARTITION is not set CONFIG_DEFAULT_DEVICE_TREE="linkit-smart-7688" CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_SPL_DM=y # CONFIG_DM_DEVICE_REMOVE is not set CONFIG_BLK=y CONFIG_LED=y CONFIG_LED_BLINK=y CONFIG_LED_GPIO=y CONFIG_MTD=y CONFIG_SPI_FLASH_GIGADEVICE=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_SPI_FLASH_MTD=y CONFIG_MT7628_ETH=y CONFIG_PHY=y CONFIG_MT76X8_USB_PHY=y CONFIG_SPI=y CONFIG_MT7621_SPI=y CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y CONFIG_USB_STORAGE=y CONFIG_FS_EXT4=y CONFIG_FS_FAT=y CONFIG_LZMA=y CONFIG_LZO=y
