Add a support for SPL which will boot from L2 LIM (0x0800_0000) and then boot U-boot FIT image including OpenSBI FW_DYNAMIC firmware and U-Boot proper images from 1st partition of MMC boot devices.
SPL related code is leverage from FSBL (https://github.com/sifive/freedom-u540-c000-bootloader.git) Signed-off-by: Pragnesh Patel <pragnesh.pa...@sifive.com> Tested-by: Yash Shah <yash.s...@sifive.com> --- board/sifive/fu540/Kconfig | 8 +++ board/sifive/fu540/Makefile | 4 ++ board/sifive/fu540/fu540-memory-map.h | 33 ++++++++++++ board/sifive/fu540/fu540.c | 24 +++++++++ board/sifive/fu540/spl.c | 78 +++++++++++++++++++++++++++ board/sifive/fu540/ux00prci.h | 56 +++++++++++++++++++ include/configs/sifive-fu540.h | 18 +++++++ 7 files changed, 221 insertions(+) create mode 100644 board/sifive/fu540/fu540-memory-map.h create mode 100644 board/sifive/fu540/spl.c create mode 100644 board/sifive/fu540/ux00prci.h diff --git a/board/sifive/fu540/Kconfig b/board/sifive/fu540/Kconfig index 900197bbb2..ebe3472f9a 100644 --- a/board/sifive/fu540/Kconfig +++ b/board/sifive/fu540/Kconfig @@ -13,12 +13,20 @@ config SYS_CONFIG_NAME default "sifive-fu540" config SYS_TEXT_BASE + default 0x80200000 if SPL default 0x80000000 if !RISCV_SMODE default 0x80200000 if RISCV_SMODE +config SPL_TEXT_BASE + default 0x08000000 + +config SPL_OPENSBI_LOAD_ADDR + default 0x80000000 + config BOARD_SPECIFIC_OPTIONS # dummy def_bool y select GENERIC_RISCV + select SUPPORT_SPL imply CMD_DHCP imply CMD_EXT2 imply CMD_EXT4 diff --git a/board/sifive/fu540/Makefile b/board/sifive/fu540/Makefile index 6e1862c475..b05e2f5807 100644 --- a/board/sifive/fu540/Makefile +++ b/board/sifive/fu540/Makefile @@ -3,3 +3,7 @@ # Copyright (c) 2019 Western Digital Corporation or its affiliates. obj-y += fu540.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +endif diff --git a/board/sifive/fu540/fu540-memory-map.h b/board/sifive/fu540/fu540-memory-map.h new file mode 100644 index 0000000000..c65203726b --- /dev/null +++ b/board/sifive/fu540/fu540-memory-map.h @@ -0,0 +1,33 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (c) 2019 SiFive, Inc + */ + +#ifndef FU540_MEMORY_MAP +#define FU540_MEMORY_MAP + +#include <asm/arch/gpio.h> +#include "ux00prci.h" + +/**************************************************************************** + * Platform definitions + *****************************************************************************/ + +/* Memory map */ +#define GPIO_CTRL_ADDR _AC(0x10060000, UL) + +#define PHYSICAL_FILTER_CTRL_ADDR _AC(0x100b8000, UL) + +#define UX00DDR_CTRL_ADDR _AC(0x100b0000, UL) +#define UX00PRCI_CTRL_ADDR _AC(0x10000000, UL) + +/* Helper functions */ +#define _REG32(p, i) (*(volatile uint32_t *)((p) + (i))) + +#define UX00PRCI_REG(offset) \ + _REG32(UX00PRCI_CTRL_ADDR, \ + offset) + +#define GPIO_REG(offset) _REG32(GPIO_CTRL_ADDR, offset) + +#endif /* FU540_MEMORY_MAP */ diff --git a/board/sifive/fu540/fu540.c b/board/sifive/fu540/fu540.c index 409471effc..fba9469c2d 100644 --- a/board/sifive/fu540/fu540.c +++ b/board/sifive/fu540/fu540.c @@ -11,6 +11,7 @@ #include <linux/delay.h> #include <linux/io.h> #include <misc.h> +#include <spl.h> /* * This define is a value used for error/unknown serial. @@ -114,3 +115,26 @@ int board_init(void) return 0; } + +#ifdef CONFIG_SPL +void board_boot_order(u32 *spl_boot_list) +{ + u8 i; + u32 boot_devices[] = { +#ifdef CONFIG_SPL_MMC_SUPPORT + BOOT_DEVICE_MMC1, +#endif + }; + + for (i = 0; i < ARRAY_SIZE(boot_devices); i++) + spl_boot_list[i] = boot_devices[i]; +} +#endif + +#ifdef CONFIG_SPL_LOAD_FIT +int board_fit_config_name_match(const char *name) +{ + /* boot using first FIT config */ + return 0; +} +#endif diff --git a/board/sifive/fu540/spl.c b/board/sifive/fu540/spl.c new file mode 100644 index 0000000000..522bc24753 --- /dev/null +++ b/board/sifive/fu540/spl.c @@ -0,0 +1,78 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (c) 2019 SiFive, Inc + * + * Authors: + * Pragnesh Patel <pragnesh.pa...@sifive.com> + */ + +#include <common.h> +#include <spl.h> +#include <misc.h> +#include <dm.h> + +#include "fu540-memory-map.h" + +#define DDRCTLPLL_F 55 +#define DDRCTLPLL_Q 2 + +#define PHY_NRESET 0x1000 + +long nsec_per_cyc = 300; /* 33.333MHz */ +void nsleep(long nsec) +{ + long step = nsec_per_cyc * 2; + + while (nsec > 0) + nsec -= step; +} + +void init_clk_and_ddr(void) +{ + int ret; + struct udevice *dev; + + /* PRCI init */ + ret = uclass_get_device(UCLASS_CLK, 0, &dev); + if (ret) { + debug("Clock init failed: %d\n", ret); + return; + } + + ret = uclass_get_device(UCLASS_RAM, 0, &dev); + if (ret) { + printf("DRAM init failed: %d\n", ret); + return; + } + + /* + * GEMGXL init VSC8541 PHY reset sequence; + * leave pull-down active for 2ms + */ + nsleep(2000000); + /* Set GPIO 12 (PHY NRESET) to OE=1 and OVAL=1 */ + GPIO_REG(GPIO_OUTPUT_VAL) |= PHY_NRESET; + GPIO_REG(GPIO_OUTPUT_EN) |= PHY_NRESET; + nsleep(100); + + /* Reset PHY again to enter unmanaged mode */ + GPIO_REG(GPIO_OUTPUT_VAL) &= ~PHY_NRESET; + nsleep(100); + GPIO_REG(GPIO_OUTPUT_VAL) |= PHY_NRESET; + nsleep(15000000); +} + +void board_init_f(ulong dummy) +{ + int ret; + + ret = spl_early_init(); + if (ret) + panic("spl_early_init() failed: %d\n", ret); + + arch_cpu_init_dm(); + + init_clk_and_ddr(); + + preloader_console_init(); +} diff --git a/board/sifive/fu540/ux00prci.h b/board/sifive/fu540/ux00prci.h new file mode 100644 index 0000000000..90ca3cd258 --- /dev/null +++ b/board/sifive/fu540/ux00prci.h @@ -0,0 +1,56 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (c) 2019 SiFive, Inc + */ + +#ifndef _SIFIVE_UX00PRCI_H +#define _SIFIVE_UX00PRCI_H + +/* Register offsets */ +#define UX00PRCI_HFROSCCFG (0x0000) +#define UX00PRCI_COREPLLCFG (0x0004) +#define UX00PRCI_COREPLLOUT (0x0008) +#define UX00PRCI_DDRPLLCFG (0x000C) +#define UX00PRCI_DDRPLLOUT (0x0010) +#define UX00PRCI_GEMGXLPLLCFG (0x001C) +#define UX00PRCI_GEMGXLPLLOUT (0x0020) +#define UX00PRCI_CORECLKSELREG (0x0024) +#define UX00PRCI_DEVICESRESETREG (0x0028) +#define UX00PRCI_CLKMUXSTATUSREG (0x002C) +#define UX00PRCI_PROCMONCFG (0x00F0) + +#define PLL_R(x) (((x) & 0x3F) << 0) +#define PLL_F(x) (((x) & 0x1FF) << 6) +#define PLL_Q(x) (((x) & 0x7) << 15) +#define PLL_RANGE(x) (((x) & 0x7) << 18) +#define PLL_BYPASS(x) (((x) & 0x1) << 24) +#define PLL_FSE(x) (((x) & 0x1) << 25) +#define PLL_LOCK(x) (((x) & 0x1) << 31) + +#define PLLOUT_DIV(x) (((x) & 0x7F) << 0) +#define PLLOUT_DIV_BY_1(x) (((x) & 0x1) << 8) +#define PLLOUT_CLK_EN(x) (((x) & 0x1) << 31) + +#define PLL_R_default 0x1 +#define PLL_F_default 0x1F +#define PLL_Q_default 0x3 +#define PLL_RANGE_default 0x0 +#define PLL_BYPASS_default 0x1 +#define PLL_FSE_default 0x1 + +#define PLLOUT_DIV_default 0x0 +#define PLLOUT_DIV_BY_1_default 0x0 +#define PLLOUT_CLK_EN_default 0x0 + +#define PLL_CORECLKSEL_HFXIN 0x1 +#define PLL_CORECLKSEL_COREPLL 0x0 + +#define DEVICESRESET_DDR_CTRL_RST_N(x) (((x) & 0x1) << 0) +#define DEVICESRESET_DDR_AXI_RST_N(x) (((x) & 0x1) << 1) +#define DEVICESRESET_DDR_AHB_RST_N(x) (((x) & 0x1) << 2) +#define DEVICESRESET_DDR_PHY_RST_N(x) (((x) & 0x1) << 3) +#define DEVICESRESET_GEMGXL_RST_N(x) (((x) & 0x1) << 5) + +#define CLKMUX_STATUS_TLCLKSEL (0x1 << 1) + +#endif // _SIFIVE_UX00PRCI_H diff --git a/include/configs/sifive-fu540.h b/include/configs/sifive-fu540.h index 2756ed5a77..ef3ae9b650 100644 --- a/include/configs/sifive-fu540.h +++ b/include/configs/sifive-fu540.h @@ -11,6 +11,22 @@ #include <linux/sizes.h> +#ifdef CONFIG_SPL + +#define CONFIG_SPL_MAX_SIZE 0x00100000 +#define CONFIG_SPL_BSS_START_ADDR 0x85000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000 +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ + CONFIG_SPL_BSS_MAX_SIZE) +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000 + +#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x84000000 + +#define CONFIG_SPL_STACK (0x08000000 + 0x001D0000 - \ + GENERATED_GBL_DATA_SIZE) + +#endif + #define CONFIG_SYS_SDRAM_BASE 0x80000000 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_2M) @@ -24,6 +40,7 @@ /* Environment options */ +#ifndef CONFIG_SPL_BUILD #define BOOT_TARGET_DEVICES(func) \ func(MMC, mmc, 0) \ func(DHCP, dhcp, na) @@ -43,5 +60,6 @@ #define CONFIG_PREBOOT \ "setenv fdt_addr ${fdtcontroladdr};" \ "fdt addr ${fdtcontroladdr};" +#endif #endif /* __CONFIG_H */ -- 2.17.1
