On Sun, Mar 8, 2020 at 3:28 PM Pragnesh Patel <[email protected]> wrote: > > Hi, > > >-----Original Message----- > >From: Palmer Dabbelt <[email protected]> > >Sent: 06 March 2020 22:32 > >To: Pragnesh Patel <[email protected]> > >Cc: [email protected]; Atish Patra <[email protected]>; > >[email protected]; Paul Walmsley <[email protected]>; > >[email protected]; Troy Benjegerdes > ><[email protected]>; Anup Patel <[email protected]>; Sagar > >Kadam <[email protected]>; Pragnesh Patel > ><[email protected]> > >Subject: Re: [PATCH v4 00/14] RISC-V SiFive FU540 support SPL > > > >On Mon, 24 Feb 2020 00:32:32 PST (-0800), [email protected] wrote: > >> This series add support for SPL to FU540.U-Boot SPL can boot from > >> L2 LIM (0x0800_0000) and jump to OpenSBI(FW_DYNAMIC firmware) and > >> U-Boot proper from MMC devices. > >> > >> How to test this patch: > >> 1) Go to OpenSBI-dir : make PLATFORM=sifive/fu540 O=build_dir > >> I=install_dir FW_DYNAMIC=y install > >> 2) cp install_dir/platform/sifive/fu540/firmware/fw_dynamic.bin > >> <u-boot-dir>/ > >> 3) Change to u-boot-dir > >> 4) make sifive_fu540_defconfig > >> 5) make all > >> 6) ZSBL loads the U-boot SPL(u-boot-spl.bin) from a partition with > >> GUID type 5B193300-FC78-40CD-8002-E86C45580B47 > >> > >> sudo dd if=spl/u-boot-spl.bin of=/dev/sdc4 bs=1M > >> > >> 7) U-boot SPL expects a u-boot FIT image(u-boot.itb) from 1st > >partition(/dev/sdc1) > >> of SD card irrespective of GUID > >> > >> sudo dd if=u-boot.itb of=/dev/sdc1 bs=1M > >> > >> Thanks to Yash Shah <[email protected]> for testing the series. > >> > >> Changes in v4: > >> - Split misc DM driver patch into multiple patches > >> - Added new SPL_CRC7_SUPPORT Kconfig option > >> - Added DM driver for DDR > >> - Added clk_enable and clk_disable ops in SiFive PRCI driver > >> - Added early clock initialization for SPL in SiFive PRCI driver > >> - Added SPL config options in sifive_fu540_defconfig instead of > >> creatiing a new config file for SPL > >> - Update fu540.rst on how to build and flash U-boot SPL > >> > >> Changes in v3: > >> - Remove arch-fu540 and arch-sifive from arch/riscv/include/asm/ > >> - Split SPL patches into DDR and SPL and spl defconfig > >> - Update fu540/MAINTAINERS file > >> - Update fu540.rst on how to build and flash U-boot SPL > >> > >> Changes in v2: > >> - Add DM driver Sifive OTP > >> - Split SPL patches into multiple patches > >> - Add a seprate patch for _image_binary_end and crc7.c > >> - Add a seprate patch to add board -u-boot.dtsi files > >> - Update FU540 RISC-V documentation > >> > >> > >> Pragnesh Patel (14): > >> misc: add driver for the SiFive otp controller > >> riscv: sifive: fu540: Use OTP DM driver for serial environment > >> variable > >> riscv: Add _image_binary_end for SPL > >> lib: Makefile: build crc7.c when CONFIG_MMC_SPI > >> riscv: sifive: dts: fu540: Add board -u-boot.dtsi files > >> sifive: fu540: add ddr driver > >> sifive: dts: fu540: Add DDR controller and phy register settings > >> clk: sifive: fu540-prci: Add clock enable and disable ops > >> clk: sifive: fu540-prci: Add clock initialization for SPL > >> riscv: sifive: fu540: add SPL configuration > >> configs: fu540: Add config options for U-boot SPL > >> riscv: sifive: fu540: enable all cache ways from u-boot proper > >> sifive: fix palmer's email address > >> doc: update FU540 RISC-V documentation > > > >Thanks for doing this. I don't see any responses here and I'm afraid I'm not > >even remotely familiar with u-boot development, but I took a look and don't > >see any issues aside from what I replied to. > > Thanks Palmer. > @[email protected] Do you have any comment on this series ?
We should target to bring the FU540 U-Boot SPL support in U-Boot v2020.07. I would like to have some test on this series. Regards, Bin
