On Tue, May 12, 2020 at 1:16 PM Matthias Brugger <[email protected]> wrote: > > > > On 12/05/2020 13:00, Belisko Marek wrote: > > On Tue, May 12, 2020 at 12:51 PM Matthias Brugger <[email protected]> wrote: > >> > >> > >> > >> On 12/05/2020 11:15, Belisko Marek wrote: > >>> On Fri, May 8, 2020 at 11:39 PM Belisko Marek <[email protected]> > >>> wrote: > >>>> > >>>> Hi Matthias, > >>>> > >>>> On Fri, May 8, 2020 at 11:28 PM Matthias Brugger <[email protected]> > >>>> wrote: > >>>>> > >>>>> Hi Marek, > >>>>> > >>>>> On 08/05/2020 21:52, Belisko Marek wrote: > >>>>>> On Wed, May 6, 2020 at 11:02 PM Belisko Marek > >>>>>> <[email protected]> wrote: > >>>>>>> > >>>>>>> On Tue, May 5, 2020 at 10:18 PM Belisko Marek > >>>>>>> <[email protected]> wrote: > >>>>>>>> > >>>>>>>> Hi, > >>>>>>>> > >>>>>>>> I'm trying to run 2019.07 u-boot on raspberrypi cm3 module but I got > >>>>>>>> no feedback on console. When used 2018.01 it boots fine. Probably I > >>>>>>>> need to do git bisect but maybe someone have some idea or experience > >>>>>>>> what can cause that. Thanks. > >>>>>>> I give a try 2020.01 and I got only this: > >>>>>>> U-Boot 2020.01 (May 06 2020 - 20:09:45 +0000) > >>>>>>> > >>>>>>> DRAM: 948 MiB > >>>>>>> RPI Compute Module 3 (0xa020a0) > >>>>>>> > >>>>>>> I'll try to debug it and let you know. > >>>>>> Debug messages shows this: > >>>>>> https://pastebin.com/2SwNzrb1 > >>>>>> > >>>>>> I tried to debug but I have no clue what is going one there. > >>>>>> > >>>>>> Also u-boot 2019.07 is not working at all on cm3 due to this commit > >>>>>> (after bisect when reverted u-boot start working again): > >>>>>> 143256b353c4d2ad1cf5e5e63b38410188b35e49 - fdt: update bcm283x device > >>>>>> tree sources to Linux 5.1-rc6 state > >>>>>> > >>>>>> Any ideas hint how to resolve this issue? Thanks. > >>>>>> > >>>>> > >>>>> Can you try to cherry-pick the following two patches to your tree: > >>>>> 5051377a0b ("arm: dts: bcm283x: Rename U-Boot file") > >>>>> 89e47e8eb6 ("fdt: fix bcm283x dm-pre-reloc definitions") > >>>> But those are present in 2020.01 and this version at least print > >>>> something to console but stuck somewhere (pls see pastebin log with > >>>> debug enabled) > >>>> I prefer to run 2020.01 ;). Thanks. > >>> Any other stuff I can try to make it working in 2020.01? Could that be > >>> firmware issue somehow? Thanks. > >> > >> Sorry I didn't realized that your first try was with 2020.01. > >> I just confirmed that it acutually does not boot. As a shortcut, do you > >> know > >> which is the last working version of U-Boot? > > v2019.07 with reverted commit : > > 143256b353c4d2ad1cf5e5e63b38410188b35e49 - fdt: update bcm283x device > > tree sources to Linux 5.1-rc6 state > > work fine. Without revert it shows anything on console. So something > > between 2019.07..2020.01 mus fix it partially ;) > > I just tired v2020.04 and it works for me. Would you mind testing that on > your end? OK I'll give a try and try to bisect between 2020.01 and 2020.04. I have dependency on 2020.01 as I integrate mender and then use this version. > > Do you have a hard dependency on v2020.01? > > Regards, > Matthias
Thanks. BR, marek -- as simple and primitive as possible ------------------------------------------------- Marek Belisko - OPEN-NANDRA Freelance Developer Ruska Nova Ves 219 | Presov, 08005 Slovak Republic Tel: +421 915 052 184 skype: marekwhite twitter: #opennandra web: http://open-nandra.com
