This board has not been converted to CONFIG_DM_SPI by the deadline.
Remove it.
Signed-off-by: Jagan Teki <ja...@amarulasolutions.com>
---
arch/powerpc/cpu/mpc85xx/Kconfig | 1 -
board/freescale/t102xqds/Kconfig | 14 -
board/freescale/t102xqds/MAINTAINERS | 12 -
board/freescale/t102xqds/Makefile | 15 -
board/freescale/t102xqds/README | 328 ---------
board/freescale/t102xqds/ddr.c | 195 -----
board/freescale/t102xqds/eth_t102xqds.c | 445 ------------
board/freescale/t102xqds/law.c | 31 -
board/freescale/t102xqds/pci.c | 23 -
board/freescale/t102xqds/spl.c | 156 ----
board/freescale/t102xqds/t1024_nand_rcw.cfg | 10 -
board/freescale/t102xqds/t1024_pbi.cfg | 26 -
board/freescale/t102xqds/t1024_sd_rcw.cfg | 10 -
board/freescale/t102xqds/t1024_spi_rcw.cfg | 10 -
board/freescale/t102xqds/t102xqds.c | 497 -------------
board/freescale/t102xqds/t102xqds.h | 14 -
board/freescale/t102xqds/t102xqds_qixis.h | 63 --
board/freescale/t102xqds/tlb.c | 116 ---
configs/T1024QDS_DDR4_SECURE_BOOT_defconfig | 69 --
configs/T1024QDS_DDR4_defconfig | 64 --
configs/T1024QDS_NAND_defconfig | 83 ---
configs/T1024QDS_SDCARD_defconfig | 80 ---
configs/T1024QDS_SECURE_BOOT_defconfig | 70 --
configs/T1024QDS_SPIFLASH_defconfig | 83 ---
configs/T1024QDS_defconfig | 67 --
include/configs/T102xQDS.h | 756 --------------------
26 files changed, 3238 deletions(-)
delete mode 100644 board/freescale/t102xqds/Kconfig
delete mode 100644 board/freescale/t102xqds/MAINTAINERS
delete mode 100644 board/freescale/t102xqds/Makefile
delete mode 100644 board/freescale/t102xqds/README
delete mode 100644 board/freescale/t102xqds/ddr.c
delete mode 100644 board/freescale/t102xqds/eth_t102xqds.c
delete mode 100644 board/freescale/t102xqds/law.c
delete mode 100644 board/freescale/t102xqds/pci.c
delete mode 100644 board/freescale/t102xqds/spl.c
delete mode 100644 board/freescale/t102xqds/t1024_nand_rcw.cfg
delete mode 100644 board/freescale/t102xqds/t1024_pbi.cfg
delete mode 100644 board/freescale/t102xqds/t1024_sd_rcw.cfg
delete mode 100644 board/freescale/t102xqds/t1024_spi_rcw.cfg
delete mode 100644 board/freescale/t102xqds/t102xqds.c
delete mode 100644 board/freescale/t102xqds/t102xqds.h
delete mode 100644 board/freescale/t102xqds/t102xqds_qixis.h
delete mode 100644 board/freescale/t102xqds/tlb.c
delete mode 100644 configs/T1024QDS_DDR4_SECURE_BOOT_defconfig
delete mode 100644 configs/T1024QDS_DDR4_defconfig
delete mode 100644 configs/T1024QDS_NAND_defconfig
delete mode 100644 configs/T1024QDS_SDCARD_defconfig
delete mode 100644 configs/T1024QDS_SECURE_BOOT_defconfig
delete mode 100644 configs/T1024QDS_SPIFLASH_defconfig
delete mode 100644 configs/T1024QDS_defconfig
delete mode 100644 include/configs/T102xQDS.h
diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index deffa831dc..96ec6360c4 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -1599,7 +1599,6 @@ source "board/freescale/mpc8572ds/Kconfig"
source "board/freescale/p1023rdb/Kconfig"
source "board/freescale/p1_twr/Kconfig"
source "board/freescale/qemu-ppce500/Kconfig"
-source "board/freescale/t102xqds/Kconfig"
source "board/freescale/t1040qds/Kconfig"
source "board/freescale/t104xrdb/Kconfig"
source "board/freescale/t208xqds/Kconfig"
diff --git a/board/freescale/t102xqds/Kconfig b/board/freescale/t102xqds/Kconfig
deleted file mode 100644
index 87818a8d3a..0000000000
--- a/board/freescale/t102xqds/Kconfig
+++ /dev/null
@@ -1,14 +0,0 @@
-if TARGET_T1024QDS
-
-config SYS_BOARD
- default "t102xqds"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "T102xQDS"
-
-source "board/freescale/common/Kconfig"
-
-endif
diff --git a/board/freescale/t102xqds/MAINTAINERS
b/board/freescale/t102xqds/MAINTAINERS
deleted file mode 100644
index 7e30e5f84b..0000000000
--- a/board/freescale/t102xqds/MAINTAINERS
+++ /dev/null
@@ -1,12 +0,0 @@
-T102XQDS BOARD
-#M: Shengzhou Liu <shengzhou....@freescale.com>
-S: Orphan (since 2018-05)
-F: board/freescale/t102xqds/
-F: include/configs/T102xQDS.h
-F: configs/T1024QDS_defconfig
-F: configs/T1024QDS_NAND_defconfig
-F: configs/T1024QDS_SDCARD_defconfig
-F: configs/T1024QDS_SPIFLASH_defconfig
-F: configs/T1024QDS_DDR4_defconfig
-F: configs/T1024QDS_SECURE_BOOT_defconfig
-F: configs/T1024QDS_DDR4_SECURE_BOOT_defconfig
diff --git a/board/freescale/t102xqds/Makefile
b/board/freescale/t102xqds/Makefile
deleted file mode 100644
index ae872b46c3..0000000000
--- a/board/freescale/t102xqds/Makefile
+++ /dev/null
@@ -1,15 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2014 Freescale Semiconductor, Inc.
-
-ifdef CONFIG_SPL_BUILD
-obj-y += spl.o
-else
-obj-y += t102xqds.o
-obj-y += eth_t102xqds.o
-obj-$(CONFIG_PCI) += pci.o
-obj-$(CONFIG_FSL_DIU_FB) += ../t1040qds/diu.o
-endif
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
diff --git a/board/freescale/t102xqds/README b/board/freescale/t102xqds/README
deleted file mode 100644
index c00e3bafbe..0000000000
--- a/board/freescale/t102xqds/README
+++ /dev/null
@@ -1,328 +0,0 @@
-T1024 SoC Overview
-------------------
-The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication
processor
-combines two or one 64-bit Power Architecture e5500 core respectively with high
-performance datapath acceleration logic, and network peripheral bus interfaces
-required for networking and telecommunications. This processor can be used in
-applications such as enterprise WLAN access points, routers, switches, firewall
-and other packet processing intensive small enterprise and branch office
appliances,
-and general-purpose embedded computing. Its high level of integration offers
-significant performance benefits and greatly helps to simplify board design.
-
-
-The T1024 SoC includes the following function and features:
-- two e5500 cores, each with a private 256 KB L2 cache
- - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant)
- - Three levels of instructions: User, supervisor, and hypervisor
- - Independent boot and reset
- - Secure boot capability
-- 256 KB shared L3 CoreNet platform cache (CPC)
-- Interconnect CoreNet platform
- - CoreNet coherency manager supporting coherent and noncoherent transactions
- with prioritization and bandwidth allocation amongst CoreNet endpoints
- - 150 Gbps coherent read bandwidth
-- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
-- Data Path Acceleration Architecture (DPAA) incorporating acceleration for
the following functions:
- - Packet parsing, classification, and distribution
- - Queue management for scheduling, packet sequencing, and congestion
management
- - Cryptography Acceleration (SEC 5.x)
- - IEEE 1588 support
- - Hardware buffer management for buffer allocation and deallocation
- - MACSEC on DPAA-based Ethernet ports
-- Ethernet interfaces
- - Four 1 Gbps Ethernet controllers
-- Parallel Ethernet interfaces
- - Two RGMII interfaces
-- High speed peripheral interfaces
- - Three PCI Express 2.0 controllers/ports running at up to 5 GHz
- - One SATA controller supporting 1.5 and 3.0 Gb/s operation
- - One QSGMII interface
- - Four SGMII interface supporting 1000 Mbps
- - Three SGMII interfaces supporting up to 2500 Mbps
- - 10GbE XFI or 10Base-KR interface
-- Additional peripheral interfaces
- - Two USB 2.0 controllers with integrated PHY
- - SD/eSDHC/eMMC
- - eSPI controller
- - Four I2C controllers
- - Four UARTs
- - Four GPIO controllers
- - Integrated flash controller (IFC)
- - LCD interface (DIU) with 12 bit dual data rate
-- Multicore programmable interrupt controller (PIC)
-- Two 8-channel DMA engines
-- Single source clocking implementation
-- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
-- QUICC Engine block
- - 32-bit RISC controller for flexible support of the communications
peripherals
- - Serial DMA channel for receive and transmit on all serial channels
- - Two universal communication controllers, supporting TDM, HDLC, and UART
-
-T1023 Personality
-------------------
-T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and
-unavailable deep sleep. Rest of the blocks are almost same as T1024.
-Differences between T1024 and T1023
-Feature T1024 T1023
-QUICC Engine: yes no
-DIU: yes no
-Deep Sleep: yes no
-I2C controller: 4 3
-DDR: 64-bit 32-bit
-IFC: 32-bit 28-bit
-
-
-T1024QDS board Overview
------------------------
-- SERDES Connections
- 4 lanes supporting the following:
- - PCI Express: supports Gen 1 and Gen 2
- - SGMII 1G and SGMII 2.5G
- - QSGMII
- - XFI
- - SATA 2.0
- - High-speed multiplexers route the SerDes traffic to appropriate slots or
connectors.
- - Aurora debug with dedicated connectors.
-- DDR Controller
- - Supports up to 1600 MTPS data-rate.
- - Supports one DDR4 or DDR3L module using DDR4 to DDR3L adapter card.
- - Supports Single-, dual- or quad-rank DIMMs
- - DDR power supplies 1.35V (DDR3L)/1.20V (DDR4) to all devices with
automatic tracking of VTT.
-- IFC/Local Bus
- - NAND Flash: 8-bit, async, up to 2GB
- - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- - NOR devices support 8 virtual banks
- - Socketed to allow alternate devices
- - GASIC: Simple (minimal) target within QIXIS FPGA
- - PromJET rapid memory download support
- - IFC Debug/Development card
-- Ethernet
- - Two on-board RGMII 10M/100M/1G ethernet ports.
- - One QSGMII interface
- - Four SGMII interface supporting 1Gbps
- - Three SGMII interfaces supporting 2.5Gbps
- - one 10Gbps XFI or 10Base-KR interface
-- QIXIS System Logic FPGA
- - Manages system power and reset sequencing.
- - Manages the configurations of DUT, board, and clock for dynamic shmoo.
- - Collects V-I-T data in background for code/power profiling.
- - Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous
assertion).
- - General fault monitoring and logging.
- - Powered from ATX 'standby' power supply that allows continuous operation
while rest of the system is off.
-- Clocks
- - System and DDR clock (SYSCLK, DDRCLK).
- - Switch selectable to one of 16 common settings in the interval of 64
MHz-166 MHz.
- - Software programmable in 1 MHz increments from 1-200 MHz.
- - SERDES clocks
- - Provides clocks to SerDes blocks and slots.
- - 100 MHz, 125 MHz and 156.25 MHz options.
- - Spread-spectrum option for 100 MHz.
-- Power Supplies
- - Dedicated PMBus regulator for VDD and VDDC.
- - Adjustable from 0.7V to 1.3V at 35A
- - VDD can be disabled independanty from VDDC for “deep sleep”.
- - DDR3L/DDR4 power supply for GVDD: 1.35 or 1.20V at up to 22A.
- - VTT/MVREF automatically track operating voltage.
- - Dedicated 2.5V VPP supply.
- - Dedicated regulators/filters for AVDD supplies.
- - Dedicated regulators for other supplies, for example OVDD, CVDD, DVDD,
LVDD, POVDD, and EVDD.
-- Video
- - DIU supports video up to 1280x1024x32 bpp.
- - Chrontel CH7201 for HDMI connection.
- - TI DS90C387R for direct LCD connection.
- - Raw (not encoded) video connector for testing or other encoders.
-- USB
- - Supports two USB 2.0 ports with integrated PHYs.
- - Two type A ports with 5V@1.5A per port.
- - Second port can be converted to OTG mini-AB.
-- SDHC
- For T1024QDS, the SDHC port connects directly to an adapter card slot that
has the following features:
- - upport for optional clock feedback paths.
- - Support for optional high-speed voltage translation direction controls.
- - Support for SD slots for: SD, SDHC (1x, 4x, 8x) and MMC.
- - Support for eMMC memory devices.
-- SPI
- -On-board support of 3 different devices and sizes.
-- Other IO
- - Two Serial ports
- - ProfiBus port
- - Four I2C ports
-
-
-Memory map on T1024QDS
-----------------------
-Start Address End Address Description Size
-0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4KB
-0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
-0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
-0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
-0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
-0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
-0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
-0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
-0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
-0xF_E000_0000 0xF_E7FF_FFFF Promjet 128MB
-0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
-0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB
-0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB
-0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB
-0x0_0000_0000 0x0_ffff_ffff DDR 4GB
-
-
-128MB NOR Flash memory Map
---------------------------
-Start Address End Address Definition Max size
-0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB
-0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB
-0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
-0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB
-0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
-0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
-0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB +
875KB
-0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
-0xEBF40000 0xEBFFFFFF U-Boot (alt bank) 768KB
-0xEBF20000 0xEBF3FFFF U-Boot env (alt bank) 128KB
-0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
-0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB
-0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
-0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
-0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
-0xE8000000 0xE801FFFF RCW (current bank) 128KB
-
-
-SerDes clock vs DIP-switch settings
------------------------------------
-SRDS_PRTCL_S1 SD1_REF_CLK1 SD1_REF_CLK2 SW4[1:4]
-0x6F 100MHz 125MHz 1101
-0xD6 100MHz 100MHz 1111
-0x99 156.25MHz 100MHz 1011
-
-
-T1024 Clock frequency
-----------------------
-BIN Core DDR Platform FMan
-Bin1: 1400MHz 1600MT/s 400MHz 700MHz
-Bin2: 1200MHz 1600MT/s 400MHz 600MHz
-Bin3: 1000MHz 1600MT/s 400MHz 500MHz
-
-
-
-Software configurations and board settings
-------------------------------------------
-1. NOR boot:
- a. build NOR boot image
- $ make T1024QDS_defconfig (For DDR3L, by default)
- or make T1024QDS_D4_defconfig (For DDR4)
- $ make
- b. program u-boot.bin image to NOR flash
- => tftp 1000000 u-boot.bin
- => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
- set SW1[1:8] = '00010011', SW2[1] = '1', SW6[1:4] = '0000' for NOR boot
-
- Switching between default bank0 and alternate bank4 on NOR flash
- To change boot source to vbank4:
- via software: run command 'qixis_reset altbank' in U-Boot.
- via DIP-switch: set SW6[1:4] = '0100'
-
- To change boot source to vbank0:
- via software: run command 'qixis_reset' in U-Boot.
- via DIP-Switch: set SW6[1:4] = '0000'
-
-2. NAND Boot:
- a. build PBL image for NAND boot
- $ make T1024QDS_NAND_defconfig
- $ make
- b. program u-boot-with-spl-pbl.bin to NAND flash
- => tftp 1000000 u-boot-with-spl-pbl.bin
- => nand erase 0 $filesize
- => nand write 1000000 0 $filesize
- set SW1[1:8] = '10000010', SW2[1] = '0' and SW6[1:4] = '1001' for NAND
boot
-
-3. SPI Boot:
- a. build PBL image for SPI boot
- $ make T1024QDS_SPIFLASH_defconfig
- $ make
- b. program u-boot-with-spl-pbl.bin to SPI flash
- => tftp 1000000 u-boot-with-spl-pbl.bin
- => sf probe 0
- => sf erase 0 f0000
- => sf write 1000000 0 $filesize
- set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
-
-4. SD Boot:
- a. build PBL image for SD boot
- $ make T1024QDS_SDCARD_defconfig
- $ make
- b. program u-boot-with-spl-pbl.bin to SD/MMC card
- => tftp 1000000 u-boot-with-spl-pbl.bin
- => mmc write 1000000 8 0x800
- => tftp 1000000 fsl_fman_ucode_t1024_xx.bin
- => mmc write 1000000 0x820 80
- set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
-
-
-DIU/QE-TDM/SDXC settings
--------------------
-a) For TDM Riser: set pin_mux=tdm in hwconfig
-b) For UCC(ProfiBus): set pin_mux=ucc in hwconfig
-c) For HDMI(DVI): set pin_mux=hdmi in hwconfig
-d) For LCD(DFP): set pin_mux=lcd in hwconfig
-e) For SDXC: set adaptor=sdxc in hwconfig
-
-2-stage NAND/SPI/SD boot loader
--------------------------------
-PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
-SPL further initializes DDR using SPD and environment variables
-and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR.
-Finally SPL transers control to U-Boot for futher booting.
-
-SPL has following features:
- - Executes within 256K
- - No relocation required
-
-Run time view of SPL framework
--------------------------------------------------
-|Area | Address |
--------------------------------------------------
-|SecureBoot header | 0xFFFC0000 (32KB) |
--------------------------------------------------
-|GD, BD | 0xFFFC8000 (4KB) |
--------------------------------------------------
-|ENV | 0xFFFC9000 (8KB) |
--------------------------------------------------
-|HEAP | 0xFFFCB000 (30KB) |
--------------------------------------------------
-|STACK | 0xFFFD8000 (22KB) |
--------------------------------------------------
-|U-Boot SPL | 0xFFFD8000 (160KB) |
--------------------------------------------------
-
-NAND Flash memory Map on T1024QDS
--------------------------------------------------------------
-Start End Definition Size
-0x000000 0x0FFFFF U-Boot 1MB
-0x100000 0x15FFFF U-Boot env 8KB
-0x160000 0x17FFFF FMAN Ucode 128KB
-0x180000 0x19FFFF QE Firmware 128KB
-
-
-SD Card memory Map on T1024QDS
-----------------------------------------------------
-Block #blocks Definition Size
-0x008 2048 U-Boot img 1MB
-0x800 0016 U-Boot env 8KB
-0x820 0256 FMAN Ucode 128KB
-0x920 0256 QE Firmware 128KB
-
-
-SPI Flash memory Map on T1024QDS
-----------------------------------------------------
-Start End Definition Size
-0x000000 0x0FFFFF U-Boot img 1MB
-0x100000 0x101FFF U-Boot env 8KB
-0x110000 0x12FFFF FMAN Ucode 128KB
-0x130000 0x14FFFF QE Firmware 128KB
-
-
-For more details, please refer to T1024QDS Reference Manual and access
-website www.freescale.com and Freescale QorIQ SDK Infocenter document.
diff --git a/board/freescale/t102xqds/ddr.c b/board/freescale/t102xqds/ddr.c
deleted file mode 100644
index c27cecd5aa..0000000000
--- a/board/freescale/t102xqds/ddr.c
+++ /dev/null
@@ -1,195 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <hwconfig.h>
-#include <init.h>
-#include <log.h>
-#include <asm/mmu.h>
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-#include <asm/fsl_law.h>
-#include <asm/mpc85xx_gpio.h>
-#include <linux/delay.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct board_specific_parameters {
- u32 n_ranks;
- u32 datarate_mhz_high;
- u32 rank_gb;
- u32 clk_adjust;
- u32 wrlvl_start;
- u32 wrlvl_ctl_2;
- u32 wrlvl_ctl_3;
-};
-
-/*
- * datarate_mhz_high values need to be in ascending order
- */
-static const struct board_specific_parameters udimm0[] = {
- /*
- * memory controller 0
- * num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
- * ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
- */
-#if defined(CONFIG_SYS_FSL_DDR4)
- {2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
- {2, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,},
- {1, 1666, 0, 8, 6, 0x0708090B, 0x0C0D0E09,},
- {1, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,},
- {1, 2200, 0, 8, 7, 0x08090A0D, 0x0F0F100C,},
-#elif defined(CONFIG_SYS_FSL_DDR3)
- {2, 833, 0, 8, 6, 0x06060607, 0x08080807,},
- {2, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,},
- {2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
- {1, 833, 0, 8, 6, 0x06060607, 0x08080807,},
- {1, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,},
- {1, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
-#else
-#error DDR type not defined
-#endif
- {}
-};
-
-static const struct board_specific_parameters *udimms[] = {
- udimm0,
-};
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
- ulong ddr_freq;
- struct cpu_type *cpu = gd->arch.cpu;
-
- if (ctrl_num > 2) {
- printf("Not supported controller number %d\n", ctrl_num);
- return;
- }
- if (!pdimm->n_ranks)
- return;
-
- pbsp = udimms[0];
-
- /* Get clk_adjust according to the board ddr freqency and n_banks
- * specified in board_specific_parameters table.
- */
- ddr_freq = get_ddr_freq(0) / 1000000;
- while (pbsp->datarate_mhz_high) {
- if (pbsp->n_ranks == pdimm->n_ranks &&
- (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
- if (ddr_freq <= pbsp->datarate_mhz_high) {
- popts->clk_adjust = pbsp->clk_adjust;
- popts->wrlvl_start = pbsp->wrlvl_start;
- popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
- popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
- goto found;
- }
- pbsp_highest = pbsp;
- }
- pbsp++;
- }
-
- if (pbsp_highest) {
- printf("Error: board specific timing not found\n");
- printf("for data rate %lu MT/s\n", ddr_freq);
- printf("Trying to use the highest speed (%u) parameters\n",
- pbsp_highest->datarate_mhz_high);
- popts->clk_adjust = pbsp_highest->clk_adjust;
- popts->wrlvl_start = pbsp_highest->wrlvl_start;
- popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
- popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
- } else {
- panic("DIMM is not supported by this board");
- }
-found:
- debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
- pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
- debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ",
- pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2);
- debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3);
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 1;
- /*
- * Write leveling override
- */
- popts->wrlvl_override = 1;
- popts->wrlvl_sample = 0xf;
-
- /*
- * rtt and rtt_wr override
- */
- popts->rtt_override = 0;
-
- /* Enable ZQ calibration */
- popts->zq_en = 1;
-
- /* DHC_EN =1, ODT = 75 Ohm */
-#ifdef CONFIG_SYS_FSL_DDR4
- popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
- popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
- DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
-#else
- popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
- popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
-
- /* optimize cpo for erratum A-009942 */
- popts->cpo_sample = 0x5f;
-#endif
-
- /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit,
- * set DDR bus width to 32bit for T1023
- */
- if (cpu->soc_ver == SVR_T1023)
- popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
-
-#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32
- /* for DDR bus 32bit test on T1024 */
- popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
-#endif
-}
-
-#if defined(CONFIG_DEEP_SLEEP)
-void board_mem_sleep_setup(void)
-{
- void __iomem *qixis_base = (void *)QIXIS_BASE;
-
- /* does not provide HW signals for power management */
- clrbits_8(qixis_base + 0x21, 0x2);
- /* Disable MCKE isolation */
- gpio_set_value(2, 0);
- udelay(1);
-}
-#endif
-
-int dram_init(void)
-{
- phys_size_t dram_size;
-
-#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
- puts("Initializing....using SPD\n");
- dram_size = fsl_ddr_sdram();
-#else
- /* DDR has been initialised by first stage boot loader */
- dram_size = fsl_ddr_sdram_size();
-#endif
- dram_size = setup_ddr_tlbs(dram_size / 0x100000);
- dram_size *= 0x100000;
-
-#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
- fsl_dp_resume();
-#endif
-
- gd->ram_size = dram_size;
-
- return 0;
-}
diff --git a/board/freescale/t102xqds/eth_t102xqds.c
b/board/freescale/t102xqds/eth_t102xqds.c
deleted file mode 100644
index 49ea21a83a..0000000000
--- a/board/freescale/t102xqds/eth_t102xqds.c
+++ /dev/null
@@ -1,445 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- *
- * Shengzhou Liu <shengzhou....@freescale.com>
- */
-
-#include <common.h>
-#include <command.h>
-#include <fdt_support.h>
-#include <log.h>
-#include <net.h>
-#include <netdev.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_law.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_portals.h>
-#include <asm/fsl_liodn.h>
-#include <malloc.h>
-#include <fm_eth.h>
-#include <fsl_mdio.h>
-#include <miiphy.h>
-#include <phy.h>
-#include <fsl_dtsec.h>
-#include <asm/fsl_serdes.h>
-#include "../common/qixis.h"
-#include "../common/fman.h"
-#include "t102xqds_qixis.h"
-
-#define EMI_NONE 0xFFFFFFFF
-#define EMI1_RGMII1 0
-#define EMI1_RGMII2 1
-#define EMI1_SLOT1 2
-#define EMI1_SLOT2 3
-#define EMI1_SLOT3 4
-#define EMI1_SLOT4 5
-#define EMI1_SLOT5 6
-#define EMI2 7
-
-static int mdio_mux[NUM_FM_PORTS];
-
-static const char * const mdio_names[] = {
- "T1024QDS_MDIO_RGMII1",
- "T1024QDS_MDIO_RGMII2",
- "T1024QDS_MDIO_SLOT1",
- "T1024QDS_MDIO_SLOT2",
- "T1024QDS_MDIO_SLOT3",
- "T1024QDS_MDIO_SLOT4",
- "T1024QDS_MDIO_SLOT5",
- "T1024QDS_MDIO_10GC",
- "NULL",
-};
-
-/* Map SerDes1 4 lanes to default slot, will be initialized dynamically */
-static u8 lane_to_slot[] = {2, 3, 4, 5};
-
-static const char *t1024qds_mdio_name_for_muxval(u8 muxval)
-{
- return mdio_names[muxval];
-}
-
-struct mii_dev *mii_dev_for_muxval(u8 muxval)
-{
- struct mii_dev *bus;
- const char *name;
-
- if (muxval > EMI2)
- return NULL;
-
- name = t1024qds_mdio_name_for_muxval(muxval);
-
- if (!name) {
- printf("No bus for muxval %x\n", muxval);
- return NULL;
- }
-
- bus = miiphy_get_dev_by_name(name);
-
- if (!bus) {
- printf("No bus by name %s\n", name);
- return NULL;
- }
-
- return bus;
-}
-
-struct t1024qds_mdio {
- u8 muxval;
- struct mii_dev *realbus;
-};
-
-static void t1024qds_mux_mdio(u8 muxval)
-{
- u8 brdcfg4;
-
- if (muxval < 7) {
- brdcfg4 = QIXIS_READ(brdcfg[4]);
- brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
- brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
- QIXIS_WRITE(brdcfg[4], brdcfg4);
- }
-}
-
-static int t1024qds_mdio_read(struct mii_dev *bus, int addr, int devad,
- int regnum)
-{
- struct t1024qds_mdio *priv = bus->priv;
-
- t1024qds_mux_mdio(priv->muxval);
-
- return priv->realbus->read(priv->realbus, addr, devad, regnum);
-}
-
-static int t1024qds_mdio_write(struct mii_dev *bus, int addr, int devad,
- int regnum, u16 value)
-{
- struct t1024qds_mdio *priv = bus->priv;
-
- t1024qds_mux_mdio(priv->muxval);
-
- return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
-}
-
-static int t1024qds_mdio_reset(struct mii_dev *bus)
-{
- struct t1024qds_mdio *priv = bus->priv;
-
- return priv->realbus->reset(priv->realbus);
-}
-
-static int t1024qds_mdio_init(char *realbusname, u8 muxval)
-{
- struct t1024qds_mdio *pmdio;
- struct mii_dev *bus = mdio_alloc();
-
- if (!bus) {
- printf("Failed to allocate t1024qds MDIO bus\n");
- return -1;
- }
-
- pmdio = malloc(sizeof(*pmdio));
- if (!pmdio) {
- printf("Failed to allocate t1024qds private data\n");
- free(bus);
- return -1;
- }
-
- bus->read = t1024qds_mdio_read;
- bus->write = t1024qds_mdio_write;
- bus->reset = t1024qds_mdio_reset;
- strcpy(bus->name, t1024qds_mdio_name_for_muxval(muxval));
-
- pmdio->realbus = miiphy_get_dev_by_name(realbusname);
-
- if (!pmdio->realbus) {
- printf("No bus with name %s\n", realbusname);
- free(bus);
- free(pmdio);
- return -1;
- }
-
- pmdio->muxval = muxval;
- bus->priv = pmdio;
- return mdio_register(bus);
-}
-
-void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
- enum fm_port port, int offset)
-{
- struct fixed_link f_link;
-
- if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_RGMII) {
- if (port == FM1_DTSEC3) {
- fdt_set_phy_handle(fdt, compat, addr, "rgmii_phy2");
- fdt_setprop_string(fdt, offset, "phy-connection-type",
- "rgmii");
- fdt_status_okay_by_alias(fdt, "emi1_rgmii1");
- }
- } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
- if (port == FM1_DTSEC1) {
- fdt_set_phy_handle(fdt, compat, addr,
- "sgmii_vsc8234_phy_s5");
- } else if (port == FM1_DTSEC2) {
- fdt_set_phy_handle(fdt, compat, addr,
- "sgmii_vsc8234_phy_s4");
- }
- } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) {
- if (port == FM1_DTSEC3) {
- fdt_set_phy_handle(fdt, compat, addr,
- "sgmii_aqr105_phy_s3");
- }
- } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_QSGMII) {
- switch (port) {
- case FM1_DTSEC1:
- fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p1");
- break;
- case FM1_DTSEC2:
- fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p2");
- break;
- case FM1_DTSEC3:
- fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p3");
- break;
- case FM1_DTSEC4:
- fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p4");
- break;
- default:
- break;
- }
- fdt_delprop(fdt, offset, "phy-connection-type");
- fdt_setprop_string(fdt, offset, "phy-connection-type",
- "qsgmii");
- fdt_status_okay_by_alias(fdt, "emi1_slot2");
- } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) {
- /* XFI interface */
- f_link.phy_id = port;
- f_link.duplex = 1;
- f_link.link_speed = 10000;
- f_link.pause = 0;
- f_link.asym_pause = 0;
- /* no PHY for XFI */
- fdt_delprop(fdt, offset, "phy-handle");
- fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link));
- fdt_setprop_string(fdt, offset, "phy-connection-type", "xgmii");
- }
-}
-
-void fdt_fixup_board_enet(void *fdt)
-{
-}
-
-/*
- * This function reads RCW to check if Serdes1{A:D} is configured
- * to slot 1/2/3/4/5 and update the lane_to_slot[] array accordingly
- */
-static void initialize_lane_to_slot(void)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_s1 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
-
- srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
-
- switch (srds_s1) {
- case 0x46:
- case 0x47:
- lane_to_slot[1] = 2;
- break;
- default:
- break;
- }
-}
-
-int board_eth_init(bd_t *bis)
-{
-#if defined(CONFIG_FMAN_ENET)
- int i, idx, lane, slot, interface;
- struct memac_mdio_info dtsec_mdio_info;
- struct memac_mdio_info tgec_mdio_info;
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_s1;
-
- srds_s1 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
- srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
-
- initialize_lane_to_slot();
-
- /* Initialize the mdio_mux array so we can recognize empty elements */
- for (i = 0; i < NUM_FM_PORTS; i++)
- mdio_mux[i] = EMI_NONE;
-
- dtsec_mdio_info.regs =
- (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
-
- dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
-
- /* Register the 1G MDIO bus */
- fm_memac_mdio_init(bis, &dtsec_mdio_info);
-
- tgec_mdio_info.regs =
- (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
- tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
-
- /* Register the 10G MDIO bus */
- fm_memac_mdio_init(bis, &tgec_mdio_info);
-
- /* Register the muxing front-ends to the MDIO buses */
- t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
- t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
- t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
- t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
- t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
- t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
- t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5);
- t1024qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2);
-
- /* Set the two on-board RGMII PHY address */
- fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
- fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
-
- switch (srds_s1) {
- case 0xd5:
- case 0xd6:
- /* QSGMII in Slot2 */
- fm_info_set_phy_address(FM1_DTSEC1, 0x8);
- fm_info_set_phy_address(FM1_DTSEC2, 0x9);
- fm_info_set_phy_address(FM1_DTSEC3, 0xa);
- fm_info_set_phy_address(FM1_DTSEC4, 0xb);
- break;
- case 0x95:
- case 0x99:
- /*
- * XFI does not need a PHY to work, but to avoid U-Boot use
- * default PHY address which is zero to a MAC when it found
- * a MAC has no PHY address, we give a PHY address to XFI
- * MAC, and should not use a real XAUI PHY address, since
- * MDIO can access it successfully, and then MDIO thinks the
- * XAUI card is used for the XFI MAC, which will cause error.
- */
- fm_info_set_phy_address(FM1_10GEC1, 4);
- fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
- break;
- case 0x6f:
- /* SGMII in Slot3, Slot4, Slot5 */
- fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5);
- fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4);
- fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
- break;
- case 0x7f:
- fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5);
- fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4);
- fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3);
- break;
- case 0x47:
- fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
- break;
- case 0x77:
- fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
- fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3);
- break;
- case 0x5a:
- fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
- break;
- case 0x6a:
- fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
- fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
- break;
- case 0x5b:
- fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
- fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
- break;
- case 0x6b:
- fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
- fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
- fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
- break;
- default:
- break;
- }
-
- for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
- idx = i - FM1_DTSEC1;
- interface = fm_info_get_enet_if(i);
- switch (interface) {
- case PHY_INTERFACE_MODE_SGMII:
- case PHY_INTERFACE_MODE_SGMII_2500:
- case PHY_INTERFACE_MODE_QSGMII:
- if (interface == PHY_INTERFACE_MODE_SGMII) {
- lane = serdes_get_first_lane(FSL_SRDS_1,
- SGMII_FM1_DTSEC1 + idx);
- } else if (interface == PHY_INTERFACE_MODE_SGMII_2500) {
- lane = serdes_get_first_lane(FSL_SRDS_1,
- SGMII_2500_FM1_DTSEC1 + idx);
- } else {
- lane = serdes_get_first_lane(FSL_SRDS_1,
- QSGMII_FM1_A);
- }
-
- if (lane < 0)
- break;
-
- slot = lane_to_slot[lane];
- debug("FM1@DTSEC%u expects SGMII in slot %u\n",
- idx + 1, slot);
- if (QIXIS_READ(present2) & (1 << (slot - 1)))
- fm_disable_port(i);
-
- switch (slot) {
- case 2:
- mdio_mux[i] = EMI1_SLOT2;
- fm_info_set_mdio(i, mii_dev_for_muxval(
- mdio_mux[i]));
- break;
- case 3:
- mdio_mux[i] = EMI1_SLOT3;
- fm_info_set_mdio(i, mii_dev_for_muxval(
- mdio_mux[i]));
- break;
- case 4:
- mdio_mux[i] = EMI1_SLOT4;
- fm_info_set_mdio(i, mii_dev_for_muxval(
- mdio_mux[i]));
- break;
- case 5:
- mdio_mux[i] = EMI1_SLOT5;
- fm_info_set_mdio(i, mii_dev_for_muxval(
- mdio_mux[i]));
- break;
- }
- break;
- case PHY_INTERFACE_MODE_RGMII:
- if (i == FM1_DTSEC3)
- mdio_mux[i] = EMI1_RGMII2;
- else if (i == FM1_DTSEC4)
- mdio_mux[i] = EMI1_RGMII1;
- fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
- break;
- default:
- break;
- }
- }
-
- for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
- idx = i - FM1_10GEC1;
- switch (fm_info_get_enet_if(i)) {
- case PHY_INTERFACE_MODE_XGMII:
- lane = serdes_get_first_lane(FSL_SRDS_1,
- XFI_FM1_MAC1 + idx);
- if (lane < 0)
- break;
- mdio_mux[i] = EMI2;
- fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
- break;
- default:
- break;
- }
- }
-
- cpu_eth_init(bis);
-#endif /* CONFIG_FMAN_ENET */
-
- return pci_eth_init(bis);
-}
diff --git a/board/freescale/t102xqds/law.c b/board/freescale/t102xqds/law.c
deleted file mode 100644
index d3c1dba934..0000000000
--- a/board/freescale/t102xqds/law.c
+++ /dev/null
@@ -1,31 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
-#ifdef CONFIG_MTD_NOR_FLASH
- SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
-#endif
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
- SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
- SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
-#endif
-#ifdef QIXIS_BASE_PHYS
- SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
- SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE_PHYS
- SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
-#endif
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t102xqds/pci.c b/board/freescale/t102xqds/pci.c
deleted file mode 100644
index 1b1cc0483c..0000000000
--- a/board/freescale/t102xqds/pci.c
+++ /dev/null
@@ -1,23 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <pci.h>
-#include <asm/fsl_pci.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <asm/fsl_serdes.h>
-
-void pci_init_board(void)
-{
- fsl_pcie_init_board(0);
-}
-
-void pci_of_setup(void *blob, bd_t *bd)
-{
- FT_FSL_PCI_SETUP;
-}
diff --git a/board/freescale/t102xqds/spl.c b/board/freescale/t102xqds/spl.c
deleted file mode 100644
index 9f4a43ed56..0000000000
--- a/board/freescale/t102xqds/spl.c
+++ /dev/null
@@ -1,156 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/* Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <clock_legacy.h>
-#include <console.h>
-#include <env_internal.h>
-#include <init.h>
-#include <malloc.h>
-#include <ns16550.h>
-#include <nand.h>
-#include <i2c.h>
-#include <mmc.h>
-#include <fsl_esdhc.h>
-#include <spi_flash.h>
-#include "../common/qixis.h"
-#include "t102xqds_qixis.h"
-#include "../common/spl.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-phys_size_t get_effective_memsize(void)
-{
- return CONFIG_SYS_L3_SIZE;
-}
-
-unsigned long get_board_sys_clk(void)
-{
- u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
-
- switch (sysclk_conf & 0x0F) {
- case QIXIS_SYSCLK_83:
- return 83333333;
- case QIXIS_SYSCLK_100:
- return 100000000;
- case QIXIS_SYSCLK_125:
- return 125000000;
- case QIXIS_SYSCLK_133:
- return 133333333;
- case QIXIS_SYSCLK_150:
- return 150000000;
- case QIXIS_SYSCLK_160:
- return 160000000;
- case QIXIS_SYSCLK_166:
- return 166666666;
- }
- return 66666666;
-}
-
-unsigned long get_board_ddr_clk(void)
-{
- u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
-
- switch ((ddrclk_conf & 0x30) >> 4) {
- case QIXIS_DDRCLK_100:
- return 100000000;
- case QIXIS_DDRCLK_125:
- return 125000000;
- case QIXIS_DDRCLK_133:
- return 133333333;
- }
- return 66666666;
-}
-
-void board_init_f(ulong bootflag)
-{
- u32 plat_ratio, sys_clk, ccb_clk;
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-
-#if defined(CONFIG_ARCH_T1040) && defined(CONFIG_SPL_NAND_BOOT)
- /*
- * There is T1040 SoC issue where NOR, FPGA are inaccessible during
- * NAND boot because IFC signals > IFC_AD7 are not enabled.
- * This workaround changes RCW source to make all signals enabled.
- */
- u32 porsr1, pinctl;
-#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000
-
- porsr1 = in_be32(&gur->porsr1);
- pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
- out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
-#endif
-
- /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
- memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
-
- /* Update GD pointer */
- gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
-
- console_init_f();
-
- /* initialize selected port with appropriate baud rate */
- sys_clk = get_board_sys_clk();
- plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
- ccb_clk = sys_clk * plat_ratio / 2;
-
- NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
- ccb_clk / 16 / CONFIG_BAUDRATE);
-
-#if defined(CONFIG_SPL_MMC_BOOT)
- puts("\nSD boot...\n");
-#elif defined(CONFIG_SPL_SPI_BOOT)
- puts("\nSPI boot...\n");
-#elif defined(CONFIG_SPL_NAND_BOOT)
- puts("\nNAND boot...\n");
-#endif
-
- relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
-}
-
-void board_init_r(gd_t *gd, ulong dest_addr)
-{
- bd_t *bd;
-
- bd = (bd_t *)(gd + sizeof(gd_t));
- memset(bd, 0, sizeof(bd_t));
- gd->bd = bd;
- bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
- bd->bi_memsize = CONFIG_SYS_L3_SIZE;
-
- arch_cpu_init();
- get_clocks();
- mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
- CONFIG_SPL_RELOC_MALLOC_SIZE);
- gd->flags |= GD_FLG_FULL_MALLOC_INIT;
-
-#ifdef CONFIG_SPL_NAND_BOOT
- nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)SPL_ENV_ADDR);
-#endif
-#ifdef CONFIG_SPL_MMC_BOOT
- mmc_initialize(bd);
- mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)SPL_ENV_ADDR);
-#endif
-#ifdef CONFIG_SPL_SPI_BOOT
- fsl_spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)SPL_ENV_ADDR);
-#endif
-
- gd->env_addr = (ulong)(SPL_ENV_ADDR);
- gd->env_valid = ENV_VALID;
-
- i2c_init_all();
-
- dram_init();
-
-#ifdef CONFIG_SPL_MMC_BOOT
- mmc_boot();
-#elif defined(CONFIG_SPL_SPI_BOOT)
- fsl_spi_boot();
-#elif defined(CONFIG_SPL_NAND_BOOT)
- nand_boot();
-#endif
-}
diff --git a/board/freescale/t102xqds/t1024_nand_rcw.cfg
b/board/freescale/t102xqds/t1024_nand_rcw.cfg
deleted file mode 100644
index 4b8f7194dc..0000000000
--- a/board/freescale/t102xqds/t1024_nand_rcw.cfg
+++ /dev/null
@@ -1,10 +0,0 @@
-# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz
-# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz
-
-# PBL preamble and RCW header for T1024QDS
-aa55aa55 010e0100
-# Serdes protocol 0x6F
-0810000e 00000000 00000000 00000000
-37800001 00000012 e8104000 21000000
-00000000 00000000 00000000 00030810
-00000000 036c5a00 00000000 00000006
diff --git a/board/freescale/t102xqds/t1024_pbi.cfg
b/board/freescale/t102xqds/t1024_pbi.cfg
deleted file mode 100644
index 98efca25a2..0000000000
--- a/board/freescale/t102xqds/t1024_pbi.cfg
+++ /dev/null
@@ -1,26 +0,0 @@
-#PBI commands
-#Initialize CPC1
-09010000 00200400
-09138000 00000000
-091380c0 00000100
-#Configure CPC1 as 256KB SRAM
-09010100 00000000
-09010104 fffc0007
-09010f00 081e000d
-09010000 80000000
-#Configure LAW for CPC1
-09000cd0 00000000
-09000cd4 fffc0000
-09000cd8 81000011
-#Configure alternate space
-09000010 00000000
-09000014 ff000000
-09000018 81000000
-#Configure SPI controller
-09110000 80000403
-09110020 2d170008
-09110024 00100008
-09110028 00100008
-0911002c 00100008
-#Flush PBL data
-091380c0 000FFFFF
diff --git a/board/freescale/t102xqds/t1024_sd_rcw.cfg
b/board/freescale/t102xqds/t1024_sd_rcw.cfg
deleted file mode 100644
index 3eca275db3..0000000000
--- a/board/freescale/t102xqds/t1024_sd_rcw.cfg
+++ /dev/null
@@ -1,10 +0,0 @@
-# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz
-# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz
-
-# PBL preamble and RCW header for T1024QDS
-aa55aa55 010e0100
-# Serdes protocol 0x6F
-0810000e 00000000 00000000 00000000
-37800001 00000012 68104000 21000000
-00000000 00000000 00000000 00030810
-00000000 036c5a00 00000000 00000006
diff --git a/board/freescale/t102xqds/t1024_spi_rcw.cfg
b/board/freescale/t102xqds/t1024_spi_rcw.cfg
deleted file mode 100644
index 1601e35fc8..0000000000
--- a/board/freescale/t102xqds/t1024_spi_rcw.cfg
+++ /dev/null
@@ -1,10 +0,0 @@
-# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz
-# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz
-
-# PBL preamble and RCW header for T1024QDS
-aa55aa55 010e0100
-# Serdes protocol 0x6F
-0810000e 00000000 00000000 00000000
-37800001 00000012 58104000 21000000
-00000000 00000000 00000000 00030810
-00000000 036c5a00 00000000 00000006
diff --git a/board/freescale/t102xqds/t102xqds.c
b/board/freescale/t102xqds/t102xqds.c
deleted file mode 100644
index 84db2fa9bc..0000000000
--- a/board/freescale/t102xqds/t102xqds.c
+++ /dev/null
@@ -1,497 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- * Copyright 2020 NXP
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <fdt_support.h>
-#include <i2c.h>
-#include <image.h>
-#include <init.h>
-#include <log.h>
-#include <netdev.h>
-#include <linux/compiler.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_law.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_liodn.h>
-#include <fm_eth.h>
-#include <hwconfig.h>
-#include "../common/qixis.h"
-#include "t102xqds.h"
-#include "t102xqds_qixis.h"
-#include "../common/sleep.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int checkboard(void)
-{
- char buf[64];
- struct cpu_type *cpu = gd->arch.cpu;
- static const char *const freq[] = {"100", "125", "156.25", "100.0"};
- int clock;
- u8 sw = QIXIS_READ(arch);
-
- printf("Board: %sQDS, ", cpu->name);
- printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4);
- printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1);
-
-#ifdef CONFIG_SDCARD
- puts("SD/MMC\n");
-#elif CONFIG_SPIFLASH
- puts("SPI\n");
-#else
- sw = QIXIS_READ(brdcfg[0]);
- sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
-
- if (sw < 0x8)
- printf("vBank: %d\n", sw);
- else if (sw == 0x8)
- puts("PromJet\n");
- else if (sw == 0x9)
- puts("NAND\n");
- else if (sw == 0x15)
- printf("IFC Card\n");
- else
- printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
-#endif
-
- printf("FPGA: v%d (%s), build %d",
- (int)QIXIS_READ(scver), qixis_read_tag(buf),
- (int)qixis_read_minor());
- /* the timestamp string contains "\n" at the end */
- printf(" on %s", qixis_read_time(buf));
-
- puts("SERDES Reference: ");
- sw = QIXIS_READ(brdcfg[2]);
- clock = (sw >> 6) & 3;
- printf("Clock1=%sMHz ", freq[clock]);
- clock = (sw >> 4) & 3;
- printf("Clock2=%sMHz\n", freq[clock]);
-
- return 0;
-}
-
-int select_i2c_ch_pca9547(u8 ch, int bus_num)
-{
- int ret;
-#ifdef CONFIG_DM_I2C
- struct udevice *dev;
-
- ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI,
- 1, &dev);
- if (ret) {
- printf("%s: Cannot find udev for a bus %d\n", __func__,
- bus_num);
- return ret;
- }
-
- ret = dm_i2c_write(dev, 0, &ch, 1);
-#else
- ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
-#endif
- if (ret) {
- puts("PCA: failed to select proper channel\n");
- return ret;
- }
-
- return 0;
-}
-
-static int board_mux_lane_to_slot(void)
-{
- ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_prtcl_s1;
- u8 brdcfg9;
-
- srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
- srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
-
-
- brdcfg9 = QIXIS_READ(brdcfg[9]);
- QIXIS_WRITE(brdcfg[9], brdcfg9 | BRDCFG9_XFI_TX_DISABLE);
-
- switch (srds_prtcl_s1) {
- case 0:
- /* SerDes1 is not enabled */
- break;
- case 0xd5:
- case 0x5b:
- case 0x6b:
- case 0x77:
- case 0x6f:
- case 0x7f:
- QIXIS_WRITE(brdcfg[12], 0x8c);
- break;
- case 0x40:
- QIXIS_WRITE(brdcfg[12], 0xfc);
- break;
- case 0xd6:
- case 0x5a:
- case 0x6a:
- case 0x56:
- QIXIS_WRITE(brdcfg[12], 0x88);
- break;
- case 0x47:
- QIXIS_WRITE(brdcfg[12], 0xcc);
- break;
- case 0x46:
- QIXIS_WRITE(brdcfg[12], 0xc8);
- break;
- case 0x95:
- case 0x99:
- brdcfg9 &= ~BRDCFG9_XFI_TX_DISABLE;
- QIXIS_WRITE(brdcfg[9], brdcfg9);
- QIXIS_WRITE(brdcfg[12], 0x8c);
- break;
- case 0x116:
- QIXIS_WRITE(brdcfg[12], 0x00);
- break;
- case 0x115:
- case 0x119:
- case 0x129:
- case 0x12b:
- /* Aurora, PCIe, SGMII, SATA */
- QIXIS_WRITE(brdcfg[12], 0x04);
- break;
- default:
- printf("WARNING: unsupported for SerDes Protocol %d\n",
- srds_prtcl_s1);
- return -1;
- }
-
- return 0;
-}
-
-#ifdef CONFIG_ARCH_T1024
-static void board_mux_setup(void)
-{
- u8 brdcfg15;
-
- brdcfg15 = QIXIS_READ(brdcfg[15]);
- brdcfg15 &= ~BRDCFG15_DIUSEL_MASK;
-
- if (hwconfig_arg_cmp("pin_mux", "tdm")) {
- /* Route QE_TDM multiplexed signals to TDM Riser slot */
- QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_TDM);
- QIXIS_WRITE(brdcfg[13], BRDCFG13_TDM_INTERFACE << 2);
- QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) &
- ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_TDM);
- } else if (hwconfig_arg_cmp("pin_mux", "ucc")) {
- /* to UCC (ProfiBus) interface */
- QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_UCC);
- } else if (hwconfig_arg_cmp("pin_mux", "hdmi")) {
- /* to DVI (HDMI) encoder */
- QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_HDMI);
- } else if (hwconfig_arg_cmp("pin_mux", "lcd")) {
- /* to DFP (LCD) encoder */
- QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_LCDFM |
- BRDCFG15_LCDPD | BRDCFG15_DIUSEL_LCD);
- }
-
- if (hwconfig_arg_cmp("adaptor", "sdxc"))
- /* Route SPI_CS multiplexed signals to SD slot */
- QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) &
- ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_SDHC);
-}
-#endif
-
-void board_retimer_ds125df111_init(void)
-{
- u8 reg;
-
-#ifdef CONFIG_DM_I2C
- struct udevice *dev;
- int ret, bus_num = 0;
-
- ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI,
- 1, &dev);
- if (ret)
- goto failed;
-
- /* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */
- reg = I2C_MUX_CH7;
- dm_i2c_write(dev, 0, ®, 1);
-
- ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_SEC,
- 1, &dev);
- if (ret)
- goto failed;
-
- reg = I2C_MUX_CH5;
- dm_i2c_write(dev, 0, ®, 1);
-
- /* Access to Control/Shared register */
- ret = i2c_get_chip_for_busnum(bus_num, I2C_RETIMER_ADDR,
- 1, &dev);
- if (ret)
- goto failed;
- reg = 0x0;
- dm_i2c_write(dev, 0xff, ®, 1);
-
- /* Read device revision and ID */
- dm_i2c_read(dev, 1, ®, 1);
- debug("Retimer version id = 0x%x\n", reg);
-
- /* Enable Broadcast */
- reg = 0x0c;
- dm_i2c_write(dev, 0xff, ®, 1);
-
- /* Reset Channel Registers */
- dm_i2c_read(dev, 0, ®, 1);
- reg |= 0x4;
- dm_i2c_write(dev, 0, ®, 1);
-
- /* Enable override divider select and Enable Override Output Mux */
- dm_i2c_read(dev, 9, ®, 1);
- reg |= 0x24;
- dm_i2c_write(dev, 9, ®, 1);
-
- /* Select VCO Divider to full rate (000) */
- dm_i2c_read(dev, 0x18, ®, 1);
- reg &= 0x8f;
- dm_i2c_write(dev, 0x18, ®, 1);
-
- /* Select active PFD MUX input as re-timed data (001) */
- dm_i2c_read(dev, 0x1e, ®, 1);
- reg &= 0x3f;
- reg |= 0x20;
- dm_i2c_write(dev, 0x1e, ®, 1);
-
- /* Set data rate as 10.3125 Gbps */
- reg = 0x0;
- dm_i2c_write(dev, 0x60, ®, 1);
- reg = 0xb2;
- dm_i2c_write(dev, 0x61, ®, 1);
- reg = 0x90;
- dm_i2c_write(dev, 0x62, ®, 1);
- reg = 0xb3;
- dm_i2c_write(dev, 0x63, ®, 1);
- reg = 0xcd;
- dm_i2c_write(dev, 0x64, ®, 1);
- return;
-
-failed:
- printf("%s: Cannot find udev for a bus %d\n", __func__,
- bus_num);
- return;
-#else
- /* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */
- reg = I2C_MUX_CH7;
- i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, ®, 1);
- reg = I2C_MUX_CH5;
- i2c_write(I2C_MUX_PCA_ADDR_SEC, 0, 1, ®, 1);
-
- /* Access to Control/Shared register */
- reg = 0x0;
- i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
-
- /* Read device revision and ID */
- i2c_read(I2C_RETIMER_ADDR, 1, 1, ®, 1);
- debug("Retimer version id = 0x%x\n", reg);
-
- /* Enable Broadcast */
- reg = 0x0c;
- i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
-
- /* Reset Channel Registers */
- i2c_read(I2C_RETIMER_ADDR, 0, 1, ®, 1);
- reg |= 0x4;
- i2c_write(I2C_RETIMER_ADDR, 0, 1, ®, 1);
-
- /* Enable override divider select and Enable Override Output Mux */
- i2c_read(I2C_RETIMER_ADDR, 9, 1, ®, 1);
- reg |= 0x24;
- i2c_write(I2C_RETIMER_ADDR, 9, 1, ®, 1);
-
- /* Select VCO Divider to full rate (000) */
- i2c_read(I2C_RETIMER_ADDR, 0x18, 1, ®, 1);
- reg &= 0x8f;
- i2c_write(I2C_RETIMER_ADDR, 0x18, 1, ®, 1);
-
- /* Select active PFD MUX input as re-timed data (001) */
- i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1);
- reg &= 0x3f;
- reg |= 0x20;
- i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1);
-
- /* Set data rate as 10.3125 Gbps */
- reg = 0x0;
- i2c_write(I2C_RETIMER_ADDR, 0x60, 1, ®, 1);
- reg = 0xb2;
- i2c_write(I2C_RETIMER_ADDR, 0x61, 1, ®, 1);
- reg = 0x90;
- i2c_write(I2C_RETIMER_ADDR, 0x62, 1, ®, 1);
- reg = 0xb3;
- i2c_write(I2C_RETIMER_ADDR, 0x63, 1, ®, 1);
- reg = 0xcd;
- i2c_write(I2C_RETIMER_ADDR, 0x64, 1, ®, 1);
-#endif
-}
-
-int board_early_init_f(void)
-{
-#if defined(CONFIG_DEEP_SLEEP)
- if (is_warm_boot())
- fsl_dp_disable_console();
-#endif
-
- return 0;
-}
-
-int board_early_init_r(void)
-{
-#ifdef CONFIG_SYS_FLASH_BASE
- const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
- int flash_esel = find_tlb_idx((void *)flashbase, 1);
-
- /*
- * Remap Boot flash + PROMJET region to caching-inhibited
- * so that flash can be erased properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- if (flash_esel == -1) {
- /* very unlikely unless something is messed up */
- puts("Error: Could not find TLB for FLASH BASE\n");
- flash_esel = 2; /* give our best effort to continue */
- } else {
- /* invalidate existing TLB entry for flash + promjet */
- disable_tlb(flash_esel);
- }
-
- set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, flash_esel, BOOKE_PAGESZ_256M, 1);
-#endif
- select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0);
- board_mux_lane_to_slot();
- board_retimer_ds125df111_init();
-
- /* Increase IO drive strength to address FCS error on RGMII */
- out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR, 0xbfdb7800);
-
- return 0;
-}
-
-unsigned long get_board_sys_clk(void)
-{
- u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
-
- switch (sysclk_conf & 0x0F) {
- case QIXIS_SYSCLK_64:
- return 64000000;
- case QIXIS_SYSCLK_83:
- return 83333333;
- case QIXIS_SYSCLK_100:
- return 100000000;
- case QIXIS_SYSCLK_125:
- return 125000000;
- case QIXIS_SYSCLK_133:
- return 133333333;
- case QIXIS_SYSCLK_150:
- return 150000000;
- case QIXIS_SYSCLK_160:
- return 160000000;
- case QIXIS_SYSCLK_166:
- return 166666666;
- }
- return 66666666;
-}
-
-unsigned long get_board_ddr_clk(void)
-{
- u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
-
- switch ((ddrclk_conf & 0x30) >> 4) {
- case QIXIS_DDRCLK_100:
- return 100000000;
- case QIXIS_DDRCLK_125:
- return 125000000;
- case QIXIS_DDRCLK_133:
- return 133333333;
- }
- return 66666666;
-}
-
-#define NUM_SRDS_PLL 2
-int misc_init_r(void)
-{
-#ifdef CONFIG_ARCH_T1024
- board_mux_setup();
-#endif
- return 0;
-}
-
-void fdt_fixup_spi_mux(void *blob)
-{
- int nodeoff = 0;
-
- if (hwconfig_arg_cmp("pin_mux", "tdm")) {
- while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
- "eon,en25s64")) >= 0) {
- fdt_del_node(blob, nodeoff);
- }
- } else {
- /* remove tdm node */
- while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
- "maxim,ds26522")) >= 0) {
- fdt_del_node(blob, nodeoff);
- }
- }
-}
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = env_get_bootm_low();
- size = env_get_bootm_size();
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#ifdef CONFIG_PCI
- pci_of_setup(blob, bd);
-#endif
-
- fdt_fixup_liodn(blob);
-
-#ifdef CONFIG_HAS_FSL_DR_USB
- fsl_fdt_fixup_dr_usb(blob, bd);
-#endif
-
-#ifdef CONFIG_SYS_DPAA_FMAN
- fdt_fixup_fman_ethernet(blob);
- fdt_fixup_board_enet(blob);
-#endif
- fdt_fixup_spi_mux(blob);
-
- return 0;
-}
-
-void qixis_dump_switch(void)
-{
- int i, nr_of_cfgsw;
-
- QIXIS_WRITE(cms[0], 0x00);
- nr_of_cfgsw = QIXIS_READ(cms[1]);
-
- puts("DIP switch settings dump:\n");
- for (i = 1; i <= nr_of_cfgsw; i++) {
- QIXIS_WRITE(cms[0], i);
- printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1]));
- }
-}
diff --git a/board/freescale/t102xqds/t102xqds.h
b/board/freescale/t102xqds/t102xqds.h
deleted file mode 100644
index d327b5edb9..0000000000
--- a/board/freescale/t102xqds/t102xqds.h
+++ /dev/null
@@ -1,14 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- * Copyright 2020 NXP
- */
-
-#ifndef __T102x_QDS_H__
-#define __T102x_QDS_H__
-
-void fdt_fixup_board_enet(void *blob);
-void pci_of_setup(void *blob, bd_t *bd);
-int select_i2c_ch_pca9547(u8 ch, int bus_num);
-
-#endif
diff --git a/board/freescale/t102xqds/t102xqds_qixis.h
b/board/freescale/t102xqds/t102xqds_qixis.h
deleted file mode 100644
index b84a33fc48..0000000000
--- a/board/freescale/t102xqds/t102xqds_qixis.h
+++ /dev/null
@@ -1,63 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#ifndef __T1024QDS_QIXIS_H__
-#define __T1024QDS_QIXIS_H__
-
-/* Definitions of QIXIS Registers for T1024/T1023 QDS */
-
-/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
-#define BRDCFG4_EMISEL_MASK 0xE0
-#define BRDCFG4_EMISEL_SHIFT 5
-
-/* BRDCFG5[0:1] controls routing and use of I2C3 & I2C4 ports*/
-#define BRDCFG5_IMX_MASK 0xC0
-#define BRDCFG5_IMX_DIU 0x80
-
-#define BRDCFG5_SPIRTE_MASK 0x07
-#define BRDCFG5_SPIRTE_TDM 0x01
-#define BRDCFG5_SPIRTE_SDHC 0x02
-#define BRDCFG9_XFI_TX_DISABLE 0x10
-
-/* BRDCFG13[0:5] TDM configuration and setup */
-#define BRDCFG13_TDM_MASK 0xfc
-#define BRDCFG13_TDM_INTERFACE 0x37
-#define BRDCFG13_HDLC_LOOPBACK 0x29
-#define BRDCFG13_TDM_LOOPBACK 0x31
-
-/* BRDCFG15[3] controls LCD Panel Powerdown */
-#define BRDCFG15_LCDFM 0x20
-#define BRDCFG15_LCDPD 0x10
-#define BRDCFG15_LCDPD_MASK 0x10
-#define BRDCFG15_LCDPD_ENABLED 0x00
-
-/* BRDCFG15[6:7] controls DIU MUX selction*/
-#define BRDCFG15_DIUSEL_MASK 0x03
-#define BRDCFG15_DIUSEL_HDMI 0x00
-#define BRDCFG15_DIUSEL_LCD 0x01
-#define BRDCFG15_DIUSEL_UCC 0x02
-#define BRDCFG15_DIUSEL_TDM 0x03
-
-/* SYSCLK */
-#define QIXIS_SYSCLK_66 0x0
-#define QIXIS_SYSCLK_83 0x1
-#define QIXIS_SYSCLK_100 0x2
-#define QIXIS_SYSCLK_125 0x3
-#define QIXIS_SYSCLK_133 0x4
-#define QIXIS_SYSCLK_150 0x5
-#define QIXIS_SYSCLK_160 0x6
-#define QIXIS_SYSCLK_166 0x7
-#define QIXIS_SYSCLK_64 0x8
-
-/* DDRCLK */
-#define QIXIS_DDRCLK_66 0x0
-#define QIXIS_DDRCLK_100 0x1
-#define QIXIS_DDRCLK_125 0x2
-#define QIXIS_DDRCLK_133 0x3
-
-
-#define QIXIS_SRDS1CLK_122 0x5a
-#define QIXIS_SRDS1CLK_125 0x5e
-#endif
diff --git a/board/freescale/t102xqds/tlb.c b/board/freescale/t102xqds/tlb.c
deleted file mode 100644
index 3546331aab..0000000000
--- a/board/freescale/t102xqds/tlb.c
+++ /dev/null
@@ -1,116 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 */
- /* *I*** - Covers boot page */
-#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
- /*
- * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
- * SRAM is at 0xfffc0000, it covered the 0xfffff000.
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_256K, 1),
-#else
- SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_4K, 1),
-#endif
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_16M, 1),
-
- /* *I*G* - Flash, localbus */
- /* This will be changed to *I*G* after relocation to RAM. */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
- 0, 2, BOOKE_PAGESZ_256M, 1),
-
-#ifndef CONFIG_SPL_BUILD
- /* *I*G* - PCI */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_1G, 1),
-
- /* *I*G* - PCI I/O */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_256K, 1),
-
- /* Bman/Qman */
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 5, BOOKE_PAGESZ_16M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
- CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_16M, 1),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 7, BOOKE_PAGESZ_16M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
- CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 8, BOOKE_PAGESZ_16M, 1),
-#endif
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 9, BOOKE_PAGESZ_4M, 1),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 10, BOOKE_PAGESZ_64K, 1),
-#endif
-#ifdef QIXIS_BASE
- SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 11, BOOKE_PAGESZ_4K, 1),
-#endif
-
-#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 12, BOOKE_PAGESZ_1G, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
- CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 13, BOOKE_PAGESZ_1G, 1)
-#endif
- /* entry 14 and 15 has been used hard coded, they will be disabled
- * in cpu_init_f, so if needed more, will use entry 16 later.
- */
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/configs/T1024QDS_DDR4_SECURE_BOOT_defconfig
b/configs/T1024QDS_DDR4_SECURE_BOOT_defconfig
deleted file mode 100644
index 2199abcb95..0000000000
--- a/configs/T1024QDS_DDR4_SECURE_BOOT_defconfig
+++ /dev/null
@@ -1,69 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_NXP_ESBC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024QDS=y
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_VIDEO=y
-CONFIG_RSA=y
-CONFIG_SPL_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/T1024QDS_DDR4_defconfig b/configs/T1024QDS_DDR4_defconfig
deleted file mode 100644
index 0a52af48bb..0000000000
--- a/configs/T1024QDS_DDR4_defconfig
+++ /dev/null
@@ -1,64 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024QDS=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xEFF20000
-CONFIG_FSL_CAAM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_VIDEO=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/T1024QDS_NAND_defconfig b/configs/T1024QDS_NAND_defconfig
deleted file mode 100644
index 9db39b1b58..0000000000
--- a/configs/T1024QDS_NAND_defconfig
+++ /dev/null
@@ -1,83 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x00201000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x140000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024QDS=y
-CONFIG_SYS_CUSTOM_LDSCRIPT=y
-CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL"
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_NAND_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_FSL_CAAM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NAND=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_VIDEO=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/T1024QDS_SDCARD_defconfig
b/configs/T1024QDS_SDCARD_defconfig
deleted file mode 100644
index 679f2ad208..0000000000
--- a/configs/T1024QDS_SDCARD_defconfig
+++ /dev/null
@@ -1,80 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x00201000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024QDS=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SDCARD"
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_MMC_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_FSL_CAAM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_VIDEO=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/T1024QDS_SECURE_BOOT_defconfig
b/configs/T1024QDS_SECURE_BOOT_defconfig
deleted file mode 100644
index cc080c7285..0000000000
--- a/configs/T1024QDS_SECURE_BOOT_defconfig
+++ /dev/null
@@ -1,70 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_NXP_ESBC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024QDS=y
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_VIDEO=y
-CONFIG_RSA=y
-CONFIG_SPL_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/T1024QDS_SPIFLASH_defconfig
b/configs/T1024QDS_SPIFLASH_defconfig
deleted file mode 100644
index 01bc5111e0..0000000000
--- a/configs/T1024QDS_SPIFLASH_defconfig
+++ /dev/null
@@ -1,83 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x00201000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024QDS=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPIFLASH"
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_SPI_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_ENV_ADDR=0xFFFC9000
-CONFIG_FSL_CAAM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_VIDEO=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/T1024QDS_defconfig b/configs/T1024QDS_defconfig
deleted file mode 100644
index 6ebffb8dd1..0000000000
--- a/configs/T1024QDS_defconfig
+++ /dev/null
@@ -1,67 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024QDS=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xEFF20000
-CONFIG_FSL_CAAM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_VIDEO=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/T102xQDS.h b/include/configs/T102xQDS.h
deleted file mode 100644
index 53ae961837..0000000000
--- a/include/configs/T102xQDS.h
+++ /dev/null
@@ -1,756 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- * Copyright 2020 NXP
- */
-
-/*
- * T1024/T1023 QDS board configuration file
- */
-
-#ifndef __T1024QDS_H
-#define __T1024QDS_H
-
-#include <linux/stringify.h>
-
-/* High Level Configuration Options */
-#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-#endif
-
-#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
-
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_DEEP_SLEEP
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xqds/t1024_pbi.cfg
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_PAD_TO 0x40000
-#define CONFIG_SPL_MAX_SIZE 0x28000
-#define RESET_VECTOR_OFFSET 0x27FFC
-#define BOOT_PAGE_OFFSET 0x27000
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_SKIP_RELOCATE
-#define CONFIG_SPL_COMMON_INIT_DDR
-#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
-#endif
-
-#ifdef CONFIG_MTD_RAW_NAND
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_nand_rcw.cfg
-#endif
-
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
-#define CONFIG_SPL_SPI_FLASH_MINIMAL
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#endif
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_spi_rcw.cfg
-#endif
-
-#ifdef CONFIG_SDCARD
-#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
-#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000)
-#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000)
-#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#endif
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_sd_rcw.cfg
-#endif
-
-#endif /* CONFIG_RAMBOOT_PBL */
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
-#endif
-
-/* PCIe Boot - Master */
-#define CONFIG_SRIO_PCIE_BOOT_MASTER
-/*
- * for slave u-boot IMAGE instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
-#else
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000
-#endif
-/*
- * for slave UCODE and ENV instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
-#else
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0xffe00000
-#endif
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
-/* slave core release by master*/
-#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
-#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
-
-/* PCIe Boot - Slave */
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
- (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
-/* Set 1M boot space for PCIe boot */
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE &
0xfff00000)
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
- (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#endif
-
-#if defined(CONFIG_SPIFLASH)
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#endif
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BACKSIDE_L2_CACHE
-#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_DDR_ECC
-#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#endif
-
-/*
- * Config the L3 Cache as L3 SRAM
- */
-#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
-#define CONFIG_SYS_L3_SIZE (256 << 10)
-#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
-#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10)
-#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_DCSRBAR 0xf0000000
-#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
-#endif
-
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-
-/*
- * DDR Setup
- */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_DDR_SPD
-
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define SPD_EEPROM_ADDRESS 0x51
-
-#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
-
-/*
- * IFC Definitions
- */
-#define CONFIG_SYS_FLASH_BASE 0xe0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-#else
-#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
-#endif
-
-#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
-#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
- + 0x8000000) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
-#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
-/* NOR Flash Timing Params */
-#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
-#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
- FTIM0_NOR_TEADC(0x5) | \
- FTIM0_NOR_TEAHC(0x5))
-#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
- FTIM1_NOR_TRAD_NOR(0x1A) |\
- FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
- FTIM2_NOR_TCH(0x4) | \
- FTIM2_NOR_TWPH(0x0E) | \
- FTIM2_NOR_TWP(0x1c))
-#define CONFIG_SYS_NOR_FTIM3 0x0
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
- + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_FSL_QIXIS /* use common QIXIS code */
-#define QIXIS_BASE 0xffdf0000
-#ifdef CONFIG_PHYS_64BIT
-#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE)
-#else
-#define QIXIS_BASE_PHYS QIXIS_BASE
-#endif
-#define QIXIS_LBMAP_SWITCH 0x06
-#define QIXIS_LBMAP_MASK 0x0f
-#define QIXIS_LBMAP_SHIFT 0
-#define QIXIS_LBMAP_DFLTBANK 0x00
-#define QIXIS_LBMAP_ALTBANK 0x04
-#define QIXIS_RST_CTL_RESET 0x31
-#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
-#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
-#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
-#define QIXIS_RST_FORCE_MEM 0x01
-
-#define CONFIG_SYS_CSPR3_EXT (0xf)
-#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 \
- | CSPR_MSEL_GPCM \
- | CSPR_V)
-#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024)
-#define CONFIG_SYS_CSOR3 0x0
-/* QIXIS Timing parameters for IFC CS3 */
-#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
- FTIM0_GPCM_TEADC(0x0e) | \
- FTIM0_GPCM_TEAHC(0x0e))
-#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
- FTIM1_GPCM_TRAD(0x3f))
-#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
- FTIM2_GPCM_TCH(0x8) | \
- FTIM2_GPCM_TWP(0x1f))
-#define CONFIG_SYS_CS3_FTIM3 0x0
-
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_BASE 0xff800000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
-#else
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#endif
-#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
- | CSPR_MSEL_NAND /* MSEL = NAND */ \
- | CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
- | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
- | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
- FTIM0_NAND_TWP(0x18) | \
- FTIM0_NAND_TWCHT(0x07) | \
- FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
- FTIM1_NAND_TWBE(0x39) | \
- FTIM1_NAND_TRR(0x0e) | \
- FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
- FTIM2_NAND_TREH(0x0a) | \
- FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3 0x0
-
-#define CONFIG_SYS_NAND_DDR_LAW 11
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
-#if defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT
-#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR
-#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
-#else
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
-#endif
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#endif
-
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_HWCONFIG
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
- ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
- CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
-#endif
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
-
-/* Serial Port */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
-#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
-
-/* Video */
-#ifdef CONFIG_ARCH_T1024 /* no DIU on T1023 */
-#define CONFIG_FSL_DIU_FB
-#ifdef CONFIG_FSL_DIU_FB
-#define CONFIG_FSL_DIU_CH7301
-#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000)
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
-/*
- * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
- * disable empty flash sector detection, which is I/O-intensive.
- */
-#undef CONFIG_SYS_FLASH_EMPTY_INFO
-#endif
-#endif
-
-/* I2C */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_FSL_I2C_SPEED 50000 /* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SPEED 50000 /* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
-#else
-#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
-#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
-#endif
-
-#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
-
-#define I2C_MUX_PCA_ADDR 0x77
-#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
-#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
-#define I2C_RETIMER_ADDR 0x18
-
-/* I2C bus multiplexer */
-#define I2C_MUX_CH_DEFAULT 0x8
-#define I2C_MUX_CH_DIU 0xC
-#define I2C_MUX_CH5 0xD
-#define I2C_MUX_CH7 0xF
-
-/* LDI/DVI Encoder for display */
-#define CONFIG_SYS_I2C_LDI_ADDR 0x38
-#define CONFIG_SYS_I2C_DVI_ADDR 0x75
-#define CONFIG_SYS_I2C_DVI_BUS_NUM 0
-
-/*
- * RTC configuration
- */
-#define RTC
-#define CONFIG_RTC_DS3231 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*
- * eSPI - Enhanced SPI
- */
-
-/*
- * General PCIe
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-#define CONFIG_PCIE1 /* PCIE controller 1 */
-#define CONFIG_PCIE2 /* PCIE controller 2 */
-#define CONFIG_PCIE3 /* PCIE controller 3 */
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-#define CONFIG_PCI_INDIRECT_BRIDGE
-
-#ifdef CONFIG_PCI
-/* controller 1, direct to uli, tgtid 3, Base address 20000 */
-#ifdef CONFIG_PCIE1
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
-#else
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
-#endif
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
-#else
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
-#endif
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-/* controller 2, Slot 2, tgtid 2, Base address 201000 */
-#ifdef CONFIG_PCIE2
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
-#else
-#define CONFIG_SYS_PCIE2_MEM_BUS 0x90000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0x90000000
-#endif
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
-#else
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
-#endif
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-/* controller 3, Slot 1, tgtid 1, Base address 202000 */
-#ifdef CONFIG_PCIE3
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
-#else
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xa0000000
-#endif
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
-#else
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
-#endif
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#endif /* CONFIG_PCI */
-
-/*
- *SATA
- */
-#define CONFIG_FSL_SATA_V2
-#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
-#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
-#define CONFIG_LBA48
-#endif
-
-/*
- * USB
- */
-#define CONFIG_HAS_FSL_DR_USB
-
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#endif
-
-/*
- * SDHC
- */
-#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#endif
-
-/* Qman/Bman */
-#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_BMAN_NUM_PORTALS 10
-#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
-#else
-#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
-#endif
-#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
-#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
-#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
-#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
- CONFIG_SYS_BMAN_CENA_SIZE)
-#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
-#define CONFIG_SYS_QMAN_NUM_PORTALS 10
-#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
-#else
-#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
-#endif
-#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
-#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
-#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
-#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
- CONFIG_SYS_QMAN_CENA_SIZE)
-#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
-
-#define CONFIG_SYS_DPAA_FMAN
-
-/* Default address of microcode for the Linux FMan driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
-#define CONFIG_SYS_QE_FW_ADDR 0x130000
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image
is
- * about 1MB (2048 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
- */
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
-#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920)
-#elif defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_SYS_FMAN_FW_ADDR (11 *
CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_SYS_QE_FW_ADDR (12 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-/*
- * Slave has no ucode locally, it can fetch this from remote. When implementing
- * in two corenet boards, slave's ucode could be stored in master's memory
- * space, the address can be mapped from slave TLB->slave LAW->
- * slave SRIO or PCIE outbound window->master inbound window->
- * master LAW->the ucode address in master's memory space.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
-#else
-#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
-#define CONFIG_SYS_QE_FW_ADDR 0xEFE00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-#endif /* CONFIG_NOBQFMAN */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define RGMII_PHY1_ADDR 0x1
-#define RGMII_PHY2_ADDR 0x2
-#define SGMII_CARD_AQ_PHY_ADDR_S3 0x3
-#define SGMII_CARD_AQ_PHY_ADDR_S4 0x4
-#define SGMII_CARD_AQ_PHY_ADDR_S5 0x5
-#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
-#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
-#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
-#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
-#endif
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME "FM1@DTSEC4"
-#endif
-
-/*
- * Dynamic MTD Partition support with mtdparts
- */
-
-/*
- * Environment
- */
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
-#define CONFIG_LOADADDR 1000000 /* default location for tftp,
bootm */
-#define __USB_PHY_TYPE utmi
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;\0" \
- "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
- "bootargs=root=/dev/ram rw console=ttyS0,115200\0" \
- "ramdiskfile=t1024qds/ramdisk.uboot\0" \
- "fdtfile=t1024qds/t1024qds.dtb\0" \
- "netdev=eth0\0" \
- "video-mode=fslfb:1024x768-32@60,monitor=dvi\0" \
- "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
- "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot && " \
- "protect off $ubootaddr +$filesize && " \
- "erase $ubootaddr +$filesize && " \
- "cp.b $loadaddr $ubootaddr $filesize && " \
- "protect on $ubootaddr +$filesize && " \
- "cmp.b $loadaddr $ubootaddr $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "fdtaddr=d00000\0" \
- "bdev=sda3\0"
-
-#define CONFIG_LINUX \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "setenv ramdiskaddr 0x02000000;" \
- "setenv fdtaddr 0x00c00000;" \
- "setenv loadaddr 0x1000000;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_LINUX
-
-#include <asm/fsl_secure_boot.h>
-
-#endif /* __T1024QDS_H */
--
2.25.1
