This patch doesn't apply correctly and the sha1 was not the correct one.
Nevertheless i update it and applied it on u-boot-stm/master
Thanks
patrice
On 8/13/20 9:45 AM, Patrice CHOTARD wrote:
> Hi Patrick
>
> On 7/30/20 1:57 PM, Patrick Delaunay wrote:
>> Remove the file board/st/stm32mp1/board.c which is not more
>> compiled since commit 156732cc8939 ("board: stm32mp1: move the
>> function board_debug_uart_init in spl.c")
>>
>> Fixes: 156732cc8939 ("board: stm32mp1: move the function
>> board_debug_uart_init in spl.c")
>> Signed-off-by: Patrick Delaunay <[email protected]>
>> ---
>> Issue when initial patch [1] was applied:
>>
>> diff --git a/board/st/stm32mp1/board.c b/board/st/stm32mp1/board.c
>> deleted file mode 100644
>>
>> [1]
>> http://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
>>
>>
>> board/st/stm32mp1/board.c | 36 ------------------------------------
>> 1 file changed, 36 deletions(-)
>> delete mode 100644 board/st/stm32mp1/board.c
>>
>> diff --git a/board/st/stm32mp1/board.c b/board/st/stm32mp1/board.c
>> deleted file mode 100644
>> index 00c61c2886..0000000000
>> --- a/board/st/stm32mp1/board.c
>> +++ /dev/null
>> @@ -1,36 +0,0 @@
>> -// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
>> -/*
>> - * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
>> - */
>> -
>> -#include <common.h>
>> -#include <asm/io.h>
>> -#include <linux/bitops.h>
>> -#include <linux/delay.h>
>> -
>> -#ifdef CONFIG_DEBUG_UART_BOARD_INIT
>> -void board_debug_uart_init(void)
>> -{
>> -#if (CONFIG_DEBUG_UART_BASE == STM32_UART4_BASE)
>> -
>> -#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00)
>> -#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28)
>> -
>> - /* UART4 clock enable */
>> - setbits_le32(RCC_MP_APB1ENSETR, BIT(16));
>> -
>> -#define GPIOG_BASE 0x50008000
>> - /* GPIOG clock enable */
>> - writel(BIT(6), RCC_MP_AHB4ENSETR);
>> - /* GPIO configuration for EVAL board
>> - * => Uart4 TX = G11
>> - */
>> - writel(0xffbfffff, GPIOG_BASE + 0x00);
>> - writel(0x00006000, GPIOG_BASE + 0x24);
>> -#else
>> -
>> -#error("CONFIG_DEBUG_UART_BASE: not supported value")
>> -
>> -#endif
>> -}
>> -#endif
> Reviewed-by: Patrice Chotard <[email protected]>
>
> Thanks
>
> Patrice
> _______________________________________________
> Uboot-stm32 mailing list
> [email protected]
> https://st-md-mailman.stormreply.com/mailman/listinfo/uboot-stm32
