Hello.
Does u-boot support HDMI output on OrangePi Win/Win Plus Allwinner A64
(SUN50I) platform?
At current time HDMI output only work after linux kernel is loaded.
Before - blank screen on a monitor (no signal).
Change setting's for video-mode=sunxi.. did not give any results. Output
only in serial console
I try:
setenv video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=1
setenv video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=1,edid=1
setenv video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=0
setenv video-mode=sunxi:1024x768-24@60,monitor=hdmi,hpd=0,edid=1
setenv video-mode=sunxi:1024x768-24@60,monitor=hdmi,hpd=1,edid=1
setenv video-mode=sunxi:1024x768-24@60,monitor=hdmi,hpd=0,edid=0
and
setenv hdmi.audio=EDID:0 disp.screen0_output_mode=1024x768p60
setenv hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1024x768p60
Need some help to debug this.
Full output of U-BOOT load
===
U-Boot SPL 2020.07-STLK1-dirty (Aug 14 2020 - 02:43:26 +0300)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.3(debug):v2.3-420-gf0b1864f8
NOTICE: BL31: Built : 15:05:30, Jul 31 2020
NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689)
NOTICE: BL31: Found U-Boot DTB at 0x4099690, model: OrangePi Win/Win
Plus
INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: PMIC: Probing AXP803 on RSB
INFO: PMIC: dcdc1 voltage: 3.300V
INFO: PMIC: dcdc5 voltage: 1.500V
INFO: PMIC: dcdc6 voltage: 1.100V
INFO: PMIC: dldo1 voltage: 3.300V
INFO: PMIC: dldo2 voltage: 3.300V
INFO: PMIC: dldo4 voltage: 3.300V
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31: cortex_a53: CPU workaround for 843419 was applied
INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
NOTICE: PSCI: System suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x4a000000
INFO: SPSR = 0x3c9
alloc space exhausted
U-Boot 2020.07-STLK1-dirty (Aug 14 2020 - 02:43:26 +0300) Allwinner
Technology
CPU: Allwinner A64 (SUN50I)
Model: OrangePi Win/Win Plus
DRAM: 2 GiB
MMC: mmc@1c0f000: 0, mmc@1c10000: 1
Loading Environment from FAT... Card did not respond to voltage select!
In: serial
Out: serial
Err: serial
Model: OrangePi Win/Win Plus
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
Bus usb@1c1a000: USB EHCI 1.00
Bus usb@1c1a400: USB OHCI 1.0
Bus usb@1c1b000: USB EHCI 1.00
Bus usb@1c1b400: USB OHCI 1.0
scanning bus usb@1c1a000 for devices... 1 USB Device(s) found
scanning bus usb@1c1a400 for devices... 1 USB Device(s) found
scanning bus usb@1c1b000 for devices... 1 USB Device(s) found
scanning bus usb@1c1b400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Autoboot in 2 seconds, press <Space> to stop
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3098 bytes read in 2 ms (1.5 MiB/s)
## Executing script at 4fc00000
U-boot loaded from SD
Boot script loaded from mmc
104 bytes read in 2 ms (50.8 KiB/s)
39702 bytes read in 5 ms (7.6 MiB/s)
3821 bytes read in 5 ms (746.1 KiB/s)
Applying kernel provided DT fixup script (sun50i-a64-fixup.scr)
## Executing script at 44000000
11888288 bytes read in 550 ms (20.6 MiB/s)
17162752 bytes read in 818 ms (20 MiB/s)
## Loading init Ramdisk from Legacy Image at 4fe00000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 11888224 Bytes = 11.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 4fa00000
Booting using the fdt blob at 0x4fa00000
EHCI failed to shut down host controller.
Loading Ramdisk to 494a9000, end 49fff660 ... OK
Loading Device Tree to 0000000049436000, end 00000000494a8fff ... OK
Starting kernel ...
