Signed-off-by: Stefan Roese <[email protected]>
---
v2:
- MAKEALL change removed
include/configs/CATcenter.h | 23 ++---------------------
1 files changed, 2 insertions(+), 21 deletions(-)
diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h
index 229a513..002435e 100644
--- a/include/configs/CATcenter.h
+++ b/include/configs/CATcenter.h
@@ -105,6 +105,7 @@
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change
*/
+#define CONFIG_PPC4xx_EMAC
#undef CONFIG_EXT_PHY
#define CONFIG_NET_MULTI 1
@@ -398,6 +399,7 @@
* I2C EEPROM (CAT24WC16) for environment
*/
#define CONFIG_HARD_I2C /* I2c with hardware support */
+#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address
*/
#define CONFIG_SYS_I2C_SLAVE 0x7F
@@ -410,16 +412,6 @@
/* last 4 bits of the address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec
*/
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405
ppc's */
- /* have only 8kB, 16kB is save here
*/
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* ... */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above
value */
-#endif
-
/*
* Init Memory Controller:
*
@@ -570,17 +562,6 @@
#define DIMM_READ_ADDR 0xAB
#define DIMM_WRITE_ADDR 0xAA
-#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register
*/
-#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register
*/
-#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register
*/
-#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register
*/
-#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register
*/
-#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register
*/
-#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register
*/
-#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register
*/
-#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR
*/
-#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register
*/
-
/* Defines for CPC0_PLLMR1 Register fields */
#define PLL_ACTIVE 0x80000000
#define CPC0_PLLMR1_SSCS 0x80000000
--
1.7.3
_______________________________________________
U-Boot mailing list
[email protected]
http://lists.denx.de/mailman/listinfo/u-boot
