On 28.09.20 19:43, Vabhav Sharma wrote:
From: Vabhav Sharma <[email protected]>
U-Boot DM model probe only single device at a time
which is enabled and configured using device tree
or platform data method.
PL011 UART IP is SBSA compliant and firmware does the
serial port set-up, initialization and let the kernel use
UART port for sending and receiving characters.
Normally software talk to one serial port time but some
LayerScape platform require all the UART devices enabled
in Linux for various use case.
Adding support to probe all enabled serial devices like SBSA
compliant PL011 UART ports probe and initialization by firmware.
Signed-off-by: Vabhav Sharma <[email protected]>
---
drivers/serial/Kconfig | 17 +++++++++++++++++
drivers/serial/serial-uclass.c | 30 ++++++++++++++++++++++++++++++
2 files changed, 47 insertions(+)
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index e344677..b2e30f1 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -134,6 +134,23 @@ config SERIAL_SEARCH_ALL
If unsure, say N.
+config SERIAL_PROBE_ALL
+ bool "Probe all available serial devices"
+ depends on DM_SERIAL
+ default n
+ help
+ The serial subsystem only probe for single serial device,
+ but does not probe for other remaining serial devices.
+ With this option set,we make probing and searching for
+ all available devices optional.
+ Normally, U-Boot talk to one serial port at a time but SBSA
+ compliant UART devices like PL011 require initialization
+ by firmware and let the kernel use serial port for sending
+ and receiving the characters.
+
+ If probing is not required for all remaining available
+ devices other than default current console device, say N.
+
config SPL_DM_SERIAL
bool "Enable Driver Model for serial drivers in SPL"
depends on DM_SERIAL && SPL_DM
diff --git a/drivers/serial/serial-uclass.c b/drivers/serial/serial-uclass.c
index 0027625..9b2fcb0 100644
--- a/drivers/serial/serial-uclass.c
+++ b/drivers/serial/serial-uclass.c
@@ -86,6 +86,11 @@ static void serial_find_console_or_panic(void)
uclass_first_device(UCLASS_SERIAL, &dev);
if (dev) {
gd->cur_serial_dev = dev;
+#ifdef CONFIG_SERIAL_PROBE_ALL
+ /* Scanning uclass to probe all devices */
+ for (; dev; uclass_next_device(&dev))
+ ;
+#endif
Please don't use #ifdef's here but instead something like this:
if (IS_ENABLED(CONFIG_SERIAL_PROBE_ALL)) {
/* Scanning uclass to probe all devices */
for (; dev; uclass_next_device(&dev))
;
}
return;
}
} else if (CONFIG_IS_ENABLED(OF_CONTROL) && blob) {
@@ -96,11 +101,21 @@ static void serial_find_console_or_panic(void)
if (np && !uclass_get_device_by_ofnode(UCLASS_SERIAL,
np_to_ofnode(np), &dev)) {
gd->cur_serial_dev = dev;
+#ifdef CONFIG_SERIAL_PROBE_ALL
+ /* Scanning uclass to probe all devices */
+ for (; dev; uclass_next_device(&dev))
+ ;
+#endif
And please everywhere else as well.
Thanks,
Stefan
return;
}
} else {
if (!serial_check_stdout(blob, &dev)) {
gd->cur_serial_dev = dev;
+#ifdef CONFIG_SERIAL_PROBE_ALL
+ /* Scanning uclass to probe all devices */
+ for (; dev; uclass_next_device(&dev))
+ ;
+#endif
return;
}
}
@@ -125,6 +140,11 @@ static void serial_find_console_or_panic(void)
!uclass_get_device(UCLASS_SERIAL, INDEX, &dev)) {
if (dev->flags & DM_FLAG_ACTIVATED) {
gd->cur_serial_dev = dev;
+#ifdef CONFIG_SERIAL_PROBE_ALL
+ /* Scanning uclass to probe all devices */
+ for (; dev; uclass_next_device(&dev))
+ ;
+#endif
return;
}
}
@@ -136,6 +156,11 @@ static void serial_find_console_or_panic(void)
if (!ret) {
/* Device did succeed probing */
gd->cur_serial_dev = dev;
+#ifdef CONFIG_SERIAL_PROBE_ALL
+ /* Scanning uclass to probe all devices */
+ for (; dev; uclass_next_device(&dev))
+ ;
+#endif
return;
}
}
@@ -144,6 +169,11 @@ static void serial_find_console_or_panic(void)
!uclass_get_device(UCLASS_SERIAL, INDEX, &dev) ||
(!uclass_first_device(UCLASS_SERIAL, &dev) && dev)) {
gd->cur_serial_dev = dev;
+#ifdef CONFIG_SERIAL_PROBE_ALL
+ /* Scanning uclass to probe all devices */
+ for (; dev; uclass_next_device(&dev))
+ ;
+#endif
return;
}
#endif
Viele Grüße,
Stefan
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
