On Thu, Oct 22, 2020 at 11:22 AM Igor Opaniuk <[email protected]> wrote: > > From: Igor Opaniuk <[email protected]> > > This documents the u-boot build and deployment procedure. > > Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]> > --- > > doc/board/toradex/apalix-imx8x.rst | 74 ++++++++++++++++++++++++++++++ > doc/board/toradex/index.rst | 1 + > 2 files changed, 75 insertions(+) > create mode 100644 doc/board/toradex/apalix-imx8x.rst > > diff --git a/doc/board/toradex/apalix-imx8x.rst > b/doc/board/toradex/apalix-imx8x.rst > new file mode 100644 > index 0000000000..ce7dde8d00 > --- /dev/null > +++ b/doc/board/toradex/apalix-imx8x.rst > @@ -0,0 +1,74 @@ > +.. SPDX-License-Identifier: GPL-2.0+ > + > +Apalis iMX8X V1.1A Module > +========================== > + > +Quick Start > +----------- > + > +- Build the ARM trusted firmware binary > +- Get scfw_tcm.bin and ahab-container.img > +- Build U-Boot > +- Load U-Boot binary using uuu > +- Flash U-Boot binary into the eMMC > +- Boot > + > +Get and Build the ARM Trusted Firmware > +-------------------------------------- > + > +.. code-block:: bash > + > + $ git clone -b toradex_imx_5.4.24_2.1.0 > http://git.toradex.com/cgit/imx-atf.git > + $ cd imx-atf/ > + $ make PLAT=imx8qx bl31 > + > +Get scfw_tcm.bin and ahab-container.img > +--------------------------------------- > + > +.. code-block:: bash > + > + $ wget > https://github.com/toradex/i.MX-System-Controller-Firmware/blob/master/src/scfw_export_mx8qx_b0/build_mx8qx_b0/mx8qx-apalis-scfw-tcm.bin > + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-seco-3.6.3.bin > + $ chmod +x imx-seco-3.6.3.bin > + $ ./imx-seco-3.6.3.bin > + > +Copy the following binaries to the U-Boot folder: > + > +.. code-block:: bash > + > + $ cp imx-atf/build/imx8qx/release/bl31.bin . > + $ cp imx-seco-3.6.3/firmware/seco/mx8qxb0-ahab-container.img > mx8qx-ahab-container.imx8_defconfig > + > +Build U-Boot > +------------ > +.. code-block:: bash > + > + $ make apalis-imx8x_defconfig > + $ make u-boot-dtb.imx > + > +Load the U-Boot Binary Using UUU > +-------------------------------- > + > +Get the latest version of the universal update utility (uuu) aka ``mfgtools > 3.0``: > + > +https://community.nxp.com/external-link.jspa?url=https%3A%2F%2Fgithub.com%2FNXPmicro%2Fmfgtools%2Freleases > + > +Put the module into USB recovery aka serial downloader mode, connect USB > device > +to your host and execute uuu: > + > +.. code-block:: bash > + > + sudo ./uuu u-boot/u-boot-dtb.imx > + > +Flash the U-Boot Binary into the eMMC > +------------------------------------- > + > +Burn the ``u-boot-dtb.imx`` binary to the primary eMMC hardware boot area > +partition and boot: > + > +.. code-block:: bash > + > + load mmc 1:1 $loadaddr u-boot-dtb.imx > + setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} / 0x200 > + mmc dev 0 1 > + mmc write ${loadaddr} 0x0 ${blkcnt} > diff --git a/doc/board/toradex/index.rst b/doc/board/toradex/index.rst > index 16b5a0770d..abba648f86 100644 > --- a/doc/board/toradex/index.rst > +++ b/doc/board/toradex/index.rst > @@ -7,6 +7,7 @@ Toradex > :maxdepth: 2 > > apalix-imx8 > + apalix-imx8x > colibri_imx7 > colibri-imx8x > verdin-imx8mm > -- > 2.17.1 > -- Best regards Oleksandr Suvorov Toradex AG Ebenaustrasse 10 | 6048 Horw | Switzerland | T: +41 41 500 48 00
