From: Takahiro Kuwano <[email protected]> Add nor->setup() and fixup hooks for volatile QE bit, overlaid erase, spi_nor_flash_parameter and mtd_info.
Signed-off-by: Takahiro Kuwano <[email protected]> --- Depends on the following patches: https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/ https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/ https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/ drivers/mtd/spi/spi-nor-core.c | 75 ++++++++++++++++++++++++++++++++++ 1 file changed, 75 insertions(+) diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c index 042da329da..fbde21a526 100644 --- a/drivers/mtd/spi/spi-nor-core.c +++ b/drivers/mtd/spi/spi-nor-core.c @@ -2592,8 +2592,83 @@ static int spi_nor_init(struct spi_nor *nor) return 0; } +#ifdef CONFIG_SPI_FLASH_SPANSION +static int s25hx_t_setup(struct spi_nor *nor, const struct flash_info *info, + const struct spi_nor_flash_parameter *params, + const struct spi_nor_hwcaps *hwcaps) +{ +#ifdef CONFIG_SPI_FLASH_BAR + return -ENOTSUPP; /* Bank Address Register is not supported */ +#endif + /* + * The Cypress Semper family has transparent ECC. To preserve + * ECC enabled, multi-pass programming within the same 16-byte + * ECC data unit needs to be avoided. Set writesize to the page + * size and remove the MTD_BIT_WRITEABLE flag in mtd_info to + * prevent multi-pass programming. + */ + nor->mtd.writesize = params->page_size; + nor->mtd.flags &= ~MTD_BIT_WRITEABLE; + + /* Emulate uniform sector architecure by this erase hook*/ + nor->mtd._erase = spansion_overlaid_erase; + /* Enter 4-byte addressing mode for WRAR used in quad_enable */ + set_4byte(nor, info, true); + + return spi_nor_default_setup(nor, info, params, hwcaps); +} + +static void s25hx_t_default_init(struct spi_nor *nor) +{ + nor->setup = s25hx_t_setup; +} + +static int s25hx_t_post_bfpt_fixup(struct spi_nor *nor, + const struct sfdp_parameter_header *header, + const struct sfdp_bfpt *bfpt, + struct spi_nor_flash_parameter *params) +{ + /* Default page size is 256-byte, but BFPT reports 512-byte */ + params->page_size = 256; + /* Reset erase size in case it is set to 4K from BFPT */ + nor->mtd.erasesize = 0; + + return 0; +} + +static void s25hx_t_post_sfdp_fixup(struct spi_nor *nor, + struct spi_nor_flash_parameter *params) +{ + /* READ_FAST_4B (0Ch) requires mode cycles*/ + params->reads[SNOR_CMD_READ_FAST].num_mode_clocks = 8; + /* PP_1_1_4 is not supported */ + params->hwcaps.mask &= ~SNOR_HWCAPS_PP_1_1_4; + /* Use volatile register to enable quad */ + params->quad_enable = spansion_quad_enable_volatile; +} + +static struct spi_nor_fixups s25hx_t_fixups = { + .default_init = s25hx_t_default_init, + .post_bfpt = s25hx_t_post_bfpt_fixup, + .post_sfdp = s25hx_t_post_sfdp_fixup, +}; +#endif + static void spi_nor_set_fixups(struct spi_nor *nor) { +#ifdef CONFIG_SPI_FLASH_SPANSION + if (JEDEC_MFR(nor->info) == SNOR_MFR_CYPRESS) { + switch (nor->info->id[1]) { + case 0x2a: /* S25HL (QSPI, 3.3V) */ + case 0x2b: /* S25HS (QSPI, 1.8V) */ + nor->fixups = &s25hx_t_fixups; + break; + + default: + break; + } + } +#endif } int spi_nor_scan(struct spi_nor *nor) -- 2.25.1
