Like for all other mvebu platforms with CONFIG_SYS_TCLK macro, define
CONFIG_SYS_REF_CLK macro for a37xx with base reference clock value which is
read from latched reset register.
Replace all usages of get_ref_clk() function by this CONFIG_SYS_REF_CLK
macro and completely remove get_ref_clk() function.
Replace also custom open-coded implementation of determining reference
clock by CONFIG_SYS_REF_CLK in a37xx serial driver.
The only difference is that macro CONFIG_SYS_REF_CLK returns base reference
clock in Hz and old function get_ref_clk() returned it in MHz.
Signed-off-by: Pali Rohár <p...@kernel.org>
---
arch/arm/mach-mvebu/armada3700/cpu.c | 24 ------------------------
arch/arm/mach-mvebu/include/mach/cpu.h | 7 -------
arch/arm/mach-mvebu/include/mach/soc.h | 4 ++++
drivers/clk/mvebu/armada-37xx-periph.c | 6 +++---
drivers/clk/mvebu/armada-37xx-tbg.c | 4 ++--
drivers/phy/marvell/comphy_a3700.c | 12 ++++++------
drivers/serial/serial_mvebu_a3700.c | 11 ++++-------
drivers/watchdog/armada-37xx-wdt.c | 2 +-
8 files changed, 20 insertions(+), 50 deletions(-)
diff --git a/arch/arm/mach-mvebu/armada3700/cpu.c
b/arch/arm/mach-mvebu/armada3700/cpu.c
index 7702028ba19b..bdf8dc377528 100644
--- a/arch/arm/mach-mvebu/armada3700/cpu.c
+++ b/arch/arm/mach-mvebu/armada3700/cpu.c
@@ -23,12 +23,6 @@
/* Armada 3700 */
#define MVEBU_GPIO_NB_REG_BASE (MVEBU_REGISTER(0x13800))
-#define MVEBU_TEST_PIN_LATCH_N (MVEBU_GPIO_NB_REG_BASE + 0x8)
-#define MVEBU_XTAL_MODE_MASK BIT(9)
-#define MVEBU_XTAL_MODE_OFFS 9
-#define MVEBU_XTAL_CLOCK_25MHZ 0x0
-#define MVEBU_XTAL_CLOCK_40MHZ 0x1
-
#define MVEBU_NB_WARM_RST_REG (MVEBU_GPIO_NB_REG_BASE + 0x40)
#define MVEBU_NB_WARM_RST_MAGIC_NUM 0x1d1e
@@ -370,21 +364,3 @@ void reset_cpu(void)
*/
writel(MVEBU_NB_WARM_RST_MAGIC_NUM, MVEBU_NB_WARM_RST_REG);
}
-
-/*
- * get_ref_clk
- *
- * return: reference clock in MHz (25 or 40)
- */
-u32 get_ref_clk(void)
-{
- u32 regval;
-
- regval = (readl(MVEBU_TEST_PIN_LATCH_N) & MVEBU_XTAL_MODE_MASK) >>
- MVEBU_XTAL_MODE_OFFS;
-
- if (regval == MVEBU_XTAL_CLOCK_25MHZ)
- return 25;
- else
- return 40;
-}
diff --git a/arch/arm/mach-mvebu/include/mach/cpu.h
b/arch/arm/mach-mvebu/include/mach/cpu.h
index 79858858c259..9b8907e0fe55 100644
--- a/arch/arm/mach-mvebu/include/mach/cpu.h
+++ b/arch/arm/mach-mvebu/include/mach/cpu.h
@@ -183,12 +183,5 @@ int a3700_dram_init_banksize(void);
/* A3700 PCIe regions fixer for device tree */
int a3700_fdt_fix_pcie_regions(void *blob);
-/*
- * get_ref_clk
- *
- * return: reference clock in MHz (25 or 40)
- */
-u32 get_ref_clk(void);
-
#endif /* __ASSEMBLY__ */
#endif /* _MVEBU_CPU_H */
diff --git a/arch/arm/mach-mvebu/include/mach/soc.h
b/arch/arm/mach-mvebu/include/mach/soc.h
index aab61f7c15cf..551eebe7d613 100644
--- a/arch/arm/mach-mvebu/include/mach/soc.h
+++ b/arch/arm/mach-mvebu/include/mach/soc.h
@@ -210,6 +210,10 @@
#define BOOT_FROM_SPI 0x3
#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
+#elif defined(CONFIG_ARMADA_3700)
+/* SAR values for Armada 3700 */
+#define CONFIG_SYS_REF_CLK ((readl(MVEBU_REGISTER(0x13808)) & BIT(9)) ? \
+ 40000000 : 25000000)
#endif
#endif /* _MVEBU_SOC_H */
diff --git a/drivers/clk/mvebu/armada-37xx-periph.c
b/drivers/clk/mvebu/armada-37xx-periph.c
index 3b767d706009..f5b3f5a78414 100644
--- a/drivers/clk/mvebu/armada-37xx-periph.c
+++ b/drivers/clk/mvebu/armada-37xx-periph.c
@@ -14,7 +14,7 @@
#include <clk.h>
#include <dm.h>
#include <asm/io.h>
-#include <asm/arch/cpu.h>
+#include <mach/soc.h>
#include <dm/device_compat.h>
#include <linux/bitops.h>
@@ -501,7 +501,7 @@ int armada_37xx_tbg_clk_dump(struct udevice *);
int soc_clk_dump(void)
{
- printf(" xtal at %u000000 Hz\n\n", get_ref_clk());
+ printf(" xtal at %u Hz\n\n", CONFIG_SYS_REF_CLK);
if (clk_dump("tbg@13200", armada_37xx_tbg_clk_dump))
return 1;
@@ -581,7 +581,7 @@ static int armada_37xx_periph_clk_probe(struct udevice *dev)
struct clk clk;
if (i == XTAL) {
- priv->parents[i] = get_ref_clk() * 1000000;
+ priv->parents[i] = CONFIG_SYS_REF_CLK;
continue;
}
diff --git a/drivers/clk/mvebu/armada-37xx-tbg.c
b/drivers/clk/mvebu/armada-37xx-tbg.c
index 054aff5e6aca..2ec60b15a6af 100644
--- a/drivers/clk/mvebu/armada-37xx-tbg.c
+++ b/drivers/clk/mvebu/armada-37xx-tbg.c
@@ -13,7 +13,7 @@
#include <clk.h>
#include <dm.h>
#include <asm/io.h>
-#include <asm/arch/cpu.h>
+#include <mach/soc.h>
#include <dm/device_compat.h>
#define NUM_TBG 4
@@ -122,7 +122,7 @@ static int armada_37xx_tbg_clk_probe(struct udevice *dev)
return -ENODEV;
}
- xtal = (ulong)get_ref_clk() * 1000000;
+ xtal = CONFIG_SYS_REF_CLK;
for (i = 0; i < NUM_TBG; ++i) {
unsigned int mult, div;
diff --git a/drivers/phy/marvell/comphy_a3700.c
b/drivers/phy/marvell/comphy_a3700.c
index 06822d1d12e0..5eb137db4884 100644
--- a/drivers/phy/marvell/comphy_a3700.c
+++ b/drivers/phy/marvell/comphy_a3700.c
@@ -211,7 +211,7 @@ static int comphy_pcie_power_up(u32 speed, u32 invert)
* 8. Check crystal jumper setting and program the Power and PLL
* Control accordingly
*/
- if (get_ref_clk() == 40) {
+ if (CONFIG_SYS_REF_CLK == 40000000) {
/* 40 MHz */
reg_set16(phy_addr(PCIE, PWR_PLL_CTRL), 0xFC63, 0xFFFF);
} else {
@@ -300,7 +300,7 @@ static int comphy_sata_power_up(u32 invert)
/*
* 2. Select reference clock and PHY mode (SATA)
*/
- if (get_ref_clk() == 40) {
+ if (CONFIG_SYS_REF_CLK == 40000000) {
/* 40 MHz */
reg_set_indirect(vphy_power_reg0, 0x3, 0x00FF);
} else {
@@ -431,7 +431,7 @@ static int comphy_usb3_power_up(u32 lane, u32 type, u32
speed, u32 invert)
* Control accordingly
* 4. Change RX wait
*/
- if (get_ref_clk() == 40) {
+ if (CONFIG_SYS_REF_CLK == 40000000) {
/* 40 MHz */
usb3_reg_set16(PWR_PLL_CTRL, 0xFCA3, 0xFFFF, lane);
usb3_reg_set16(PWR_MGM_TIM1, 0x10C, 0xFFFF, lane);
@@ -556,7 +556,7 @@ static int comphy_usb2_power_up(u8 usb32)
* 0. Setup PLL. 40MHz clock uses defaults.
* See "PLL Settings for Typical REFCLK" table
*/
- if (get_ref_clk() == 25) {
+ if (CONFIG_SYS_REF_CLK == 25000000) {
reg_set(USB2_PHY_BASE(usb32), 5 | (96 << 16),
0x3F | (0xFF << 16) | (0x3 << 28));
}
@@ -773,7 +773,7 @@ static int comphy_sgmii_power_up(u32 lane, u32 speed, u32
invert)
* 11. Set correct reference clock frequency in COMPHY register
* REF_FREF_SEL.
*/
- if (get_ref_clk() == 40) {
+ if (CONFIG_SYS_REF_CLK == 40000000) {
reg_set16(sgmiiphy_addr(lane, PWR_PLL_CTRL),
0x4 << rf_ref_freq_sel_shift, rf_ref_freq_sel_mask);
} else {
@@ -820,7 +820,7 @@ static int comphy_sgmii_power_up(u32 lane, u32 speed, u32
invert)
*/
debug("Running C-DPI phy init %s mode\n",
speed == COMPHY_SPEED_3_125G ? "2G5" : "1G");
- if (get_ref_clk() == 40)
+ if (CONFIG_SYS_REF_CLK == 40000000)
comphy_sgmii_phy_init(lane, speed);
/*
diff --git a/drivers/serial/serial_mvebu_a3700.c
b/drivers/serial/serial_mvebu_a3700.c
index efc898c08e83..b575b70050c4 100644
--- a/drivers/serial/serial_mvebu_a3700.c
+++ b/drivers/serial/serial_mvebu_a3700.c
@@ -8,7 +8,7 @@
#include <dm.h>
#include <serial.h>
#include <asm/io.h>
-#include <asm/arch/cpu.h>
+#include <mach/soc.h>
#include <linux/delay.h>
struct mvebu_plat {
@@ -237,7 +237,7 @@ static int mvebu_serial_remove(struct udevice *dev)
/* Calculate new divisor against XTAL clock without changing baudrate */
new_oversampling = 0;
- new_parent_rate = get_ref_clk() * 1000000;
+ new_parent_rate = CONFIG_SYS_REF_CLK;
new_divider = DIV_ROUND_CLOSEST(new_parent_rate * divider * d1 * d2 *
oversampling, parent_rate * 16);
@@ -347,12 +347,11 @@ U_BOOT_DRIVER(serial_mvebu) = {
#ifdef CONFIG_DEBUG_MVEBU_A3700_UART
#include <debug_uart.h>
-#include <mach/soc.h>
static inline void _debug_uart_init(void)
{
void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
- u32 parent_rate, divider;
+ u32 divider;
/* reset FIFOs */
writel(UART_CTRL_RXFIFO_RESET | UART_CTRL_TXFIFO_RESET,
@@ -365,9 +364,7 @@ static inline void _debug_uart_init(void)
* Calculate divider
* baudrate = clock / 16 / divider
*/
- parent_rate = (readl(MVEBU_REGISTER(0x13808)) & BIT(9)) ?
- 40000000 : 25000000;
- divider = DIV_ROUND_CLOSEST(parent_rate, CONFIG_BAUDRATE * 16);
+ divider = DIV_ROUND_CLOSEST(CONFIG_SYS_REF_CLK, CONFIG_BAUDRATE * 16);
writel(divider, base + UART_BAUD_REG);
/*
diff --git a/drivers/watchdog/armada-37xx-wdt.c
b/drivers/watchdog/armada-37xx-wdt.c
index 6b5e1ab6fc35..915f37b3d8e6 100644
--- a/drivers/watchdog/armada-37xx-wdt.c
+++ b/drivers/watchdog/armada-37xx-wdt.c
@@ -165,7 +165,7 @@ static int a37xx_wdt_probe(struct udevice *dev)
goto err;
priv->reg = (void __iomem *)addr;
- priv->clk_rate = (ulong)get_ref_clk() * 1000000;
+ priv->clk_rate = CONFIG_SYS_REF_CLK;
/*
* We use counter 1 as watchdog timer, therefore we only set bit
--
2.20.1
