From: Marcel Ziswiler <[email protected]>
While most boards meanwhile migrated to using binman a few like the
verdin-imx8mm are still using the legacy image generation.
Unfortunately, the legacy image generation is currently broken which is
especially bad for any kind of bisection attempts.
Anyway, this fixes it even though we will also migrate to using binman
shortly.
Fixes: commit cb9faa6f98ae
("tools: Use a single target-independent config to enable OpenSSL")
Signed-off-by: Marcel Ziswiler <[email protected]>
---
arch/arm/mach-imx/mkimage_fit_atf.sh | 26 +++++++++++++-------------
1 file changed, 13 insertions(+), 13 deletions(-)
diff --git a/arch/arm/mach-imx/mkimage_fit_atf.sh
b/arch/arm/mach-imx/mkimage_fit_atf.sh
index 2a17968794c..2d6c46633c7 100755
--- a/arch/arm/mach-imx/mkimage_fit_atf.sh
+++ b/arch/arm/mach-imx/mkimage_fit_atf.sh
@@ -53,7 +53,7 @@ cat << __HEADER_EOF
description = "Configuration to load ATF before U-Boot";
images {
- uboot@1 {
+ uboot_1 {
description = "U-Boot (64-bit)";
os = "u-boot";
data = /incbin/("$BL33");
@@ -68,7 +68,7 @@ cnt=1
for dtname in $*
do
cat << __FDT_IMAGE_EOF
- fdt@$cnt {
+ fdt_$cnt {
description = "$(basename $dtname .dtb)";
data = /incbin/("$dtname");
type = "flat_dt";
@@ -79,7 +79,7 @@ cnt=$((cnt+1))
done
cat << __HEADER_EOF
- atf@1 {
+ atf_1 {
description = "ARM Trusted Firmware";
os = "arm-trusted-firmware";
data = /incbin/("$BL31");
@@ -93,7 +93,7 @@ __HEADER_EOF
if [ -f $BL32 ]; then
cat << __HEADER_EOF
- tee@1 {
+ tee_1 {
description = "TEE firmware";
data = /incbin/("$BL32");
type = "firmware";
@@ -108,7 +108,7 @@ fi
cat << __CONF_HEADER_EOF
};
configurations {
- default = "config@1";
+ default = "config_1";
__CONF_HEADER_EOF
@@ -117,20 +117,20 @@ for dtname in $*
do
if [ -f $BL32 ]; then
cat << __CONF_SECTION_EOF
- config@$cnt {
+ config_$cnt {
description = "$(basename $dtname .dtb)";
- firmware = "uboot@1";
- loadables = "atf@1", "tee@1";
- fdt = "fdt@$cnt";
+ firmware = "uboot_1";
+ loadables = "atf_1", "tee_1";
+ fdt = "fdt_$cnt";
};
__CONF_SECTION_EOF
else
cat << __CONF_SECTION1_EOF
- config@$cnt {
+ config_$cnt {
description = "$(basename $dtname .dtb)";
- firmware = "uboot@1";
- loadables = "atf@1";
- fdt = "fdt@$cnt";
+ firmware = "uboot_1";
+ loadables = "atf_1";
+ fdt = "fdt_$cnt";
};
__CONF_SECTION1_EOF
fi
--
2.26.2
