Hi Pali,
On 25.10.21 16:42, Pali Rohár wrote:
On Monday 25 October 2021 16:39:44 Stefan Roese wrote:
Hi Marek,
On 25.10.21 15:12, Marek Behún wrote:
From: Marek Behún <marek.be...@nic.cz>
Hello Stefan,
these are another improvements for kwboot, please apply only after series
arm: mvebu: nandpagesize support for kwbimage v1
I'm checking right now and have applied the 3 NAND patches on current
master. But this patchset fails at this one:
tools: kwboot: Do not modify kwbimage header before increasing its size
[stefan@ryzen u-boot-marvell (kwboot-test1)]$ git am -3 ~/tmp/kwboot2/*
Applying: tools: kwboot: Initialize rfds to zero
Applying: tools: kwboot: Fix initialization of tty device
Applying: tools: kwboot: Reserve enough space for patching kwbimage in
memory
Applying: tools: kwboot: Validate 4-byte image data checksum
Applying: tools: kwboot: Inject baudrate change back code after data part
Applying: tools: kwboot: Recalculate 4-byte data checksum after injecting
baudrate code
Applying: tools: kwboot: Correctly set configuration of UART for BootROM
messages
Applying: tools: kwboot: Show verbose message when waiting for baudrate
change magic
Applying: tools: kwboot: Simplify code for aligning image header
Applying: tools: kwboot: Do not modify kwbimage header before increasing its
size
error: sha1 information is lacking or useless (tools/kwboot.c).
error: could not build fake ancestor
Patch failed at 0010 tools: kwboot: Do not modify kwbimage header before
increasing its size
hint: Use 'git am --show-current-patch=diff' to see the failed patch
When you have resolved this problem, run "git am --continue".
If you prefer to skip this patch, run "git am --skip" instead.
To restore the original branch and stop patching, run "git am --abort".
Any idea what's missing here?
Hello! I'm using also this patch:
https://patchwork.ozlabs.org/project/uboot/patch/20211021144609.9319-2-p...@kernel.org/
Ah, yes. That does the trick. Now all patches apply clean. Thanks.
Testing with all these patches on my AXP target does show, it still
does not work with baudrate > 115k:
[stefan@ryzen u-boot-marvell (kwboot-test1)]$ ./tools/kwboot -B 230400
-b u-boot-spl.kwb -t
/dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A1019EGY-if00-port0
Patching image boot signature to UART
Injecting binary header code for changing baudrate to 230400 Bd
Injecting code for changing baudrate back
Sending boot message. Please reboot the target...|
Waiting 2s and flushing tty
Sending boot image header (90112 bytes)...
0 %
[......................................................................]
10 %
[......................................................................]
20 %
[......................................................................]
29 %
[......................................................................]
39 %
[......................................................................]
49 %
[......................................................................]
59 %
[......................................................................]
69 %
[......................................................................]
79 %
[......................................................................]
89 %
[......................................................................]
99 % [....
]
Done
U-Boot SPL 2021.10-00908-gc129aa2f173a (Oct 25 2021 - 17:10:55 +0200)
High speed PHY - Version: 2.1.5 (COM-PHY-V20)
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.4
DDR3 Training Sequence - Ended Successfully
Trying to boot from BOOTROM
Returning to BootROM (return address 0xffff0aa0)...
Changing baudrate to 230400 Bd
Baudrate was not changed
xmodem: Protocol error
[stefan@ryzen u-boot-marvell (kwboot-test1)]$
Not changing the baudrate still works. Any idea what I should test? Or
do you have further changes in the queue that I should wait upon?
Thanks,
Stefan
