Dne torek, 14. december 2021 ob 02:07:58 CET je Andre Przywara napisal(a): > On Mon, 13 Dec 2021 18:20:37 +0100 > Jernej Škrabec <jernej.skra...@gmail.com> wrote: > > Hi Jernej, > > thanks for having a look! > > > Dne ponedeljek, 13. december 2021 ob 02:03:22 CET je Andre Przywara > > napisal(a): > > > Add some long overdue instructions for building and installing U-Boot on > > > Allwinner SoC based boards. > > > This describes the building process, including TF-A and crust, plus > > > installation to SD card, eMMC and SPI flash, both from Linux and U-Boot > > > itself. Also describe FEL booting. > > > > > > Signed-off-by: Andre Przywara <andre.przyw...@arm.com> > > > --- > > > Hi, > > > > > > please have a look whether this makes sense. Feel free to just try > > something, > > > and point out ambiguities or missing bits. For missing topics, please > > > send a follow-up patch ;-) > > > > This documentation seems to include all of board/sunxi/README.sunxi64 and > > README.nand. I think it would make sense to remove those files. If any file gets > > out of sync for any reason, it would be very confusing for end user. > > Indeed, I think README.sunxi64 is redundant now. > I didn't look at README.nand too closely, but since I don't even mention > NAND, I don't think it can be removed just yet. I guess I just convert > it to RST and move it into this directory. > > > I would also remove all non-essential command parameters, so all commands are > > as simple as possible. Power users will know about them anyway and non- skilled > > users might perceive that it's harder that it really is. I have in mind "- j5 - > > s" for make, "-v -p" for sunxi-fel > > I see, makes sense. > > > and DEBUG=1 for TF-A (maybe I missed some > > places). Actually, DEBUG=1 could be mentioned afterwards as troubleshooting > > step. In my experience, stable version of TF-A was never source of boot issues > > nor it provided any useful information for debugging anything else. > > Well, I'd tend to keep DEBUG=1 enabled, this lists the regulators > enabled, which helps debugging. Also in the past DEBUG=0 was very > silent, which wasn't helpful to verify that TF-A actually started.
I patched out enabling regulators in TF-A, we already discussed this in the past. > > Do you typically build or recommend DEBUG=0? I set DEBUG=1 only when I actually want to debug this part of boot process, which is very rarely. I don't remember that I would help anyone with building TF-A, so I don't make recommendations in either direction. For LibreELEC, we build it with DEBUG=0, unless debug build of ATF package was requested. Again, basically never. Release images are build with DEBUG=0. Note that based on my experience, many LibreELEC users don't actually own serial adapter, so it doesn't really matter what U-Boot and TF-A print out. Fortunatelly, boot issues in LE are very rare these days (I don't remember last time someone reported it). Best regards, Jernej > > > Some comments bellow. > > > > > > > > Also this is quite long, shall this be split up in two (or more) files? > > > > > > This is what rst.ninjs.org made of it, if you prefer to read it formatted: > > > https://paste.c-net.org/PleasantNeedy > > > > > > Cheers, > > > Andre > > > > > > doc/board/allwinner/index.rst | 9 + > > > doc/board/allwinner/sunxi.rst | 304 ++++++++++++++++++++++++++++++++++ > > > 2 files changed, 313 insertions(+) > > > create mode 100644 doc/board/allwinner/index.rst > > > create mode 100644 doc/board/allwinner/sunxi.rst > > > > > > diff --git a/doc/board/allwinner/index.rst b/doc/board/allwinner/ index.rst > > > new file mode 100644 > > > index 00000000000..7352ccd5c0a > > > --- /dev/null > > > +++ b/doc/board/allwinner/index.rst > > > @@ -0,0 +1,9 @@ > > > +.. SPDX-License-Identifier: GPL-2.0+ > > > + > > > +Allwinner (sunxi) boards > > > +======================== > > > + > > > +.. toctree:: > > > + :maxdepth: 2 > > > + > > > + sunxi > > > diff --git a/doc/board/allwinner/sunxi.rst b/doc/board/allwinner/ sunxi.rst > > > new file mode 100644 > > > index 00000000000..693eb32e168 > > > --- /dev/null > > > +++ b/doc/board/allwinner/sunxi.rst > > > @@ -0,0 +1,304 @@ > > > +.. SPDX-License-Identifier: GPL-2.0+ > > > +.. Copyright (C) 2021 Arm Ltd. > > > + > > > +Allwinner SoC based boards > > > +========================== > > > +For boards using an Allwinner ARM based SoC ("sunxi"), the U-Boot build > > > +system generates a single integrated image file: ``u-boot-sunxi-with- > > spl.bin.`` > > > +This file can be used on SD cards, eMMC devices, SPI flash and for the > > > +USB-OTG based boot method (FEL). To build this file: > > > + > > > +* For 64-bit SoCs, build Trusted Firmware (TF-A, formerly known as ATF) > > > > > first, > > > + you will need its ``bl31.bin``. See below for more details. > > > +* Optionally on 64-bit SoCs, build the crust management processor firmware. > > > +* Build U-Boot:: > > > + > > > + $ export BL31=/path/to/bl31.bin # required for 64-bit SoCs > > > + $ export SCP=/src/crust/build/scp/scp.bin # optional for some 64- bit > > SoCs > > > > NIT: I guess path for SCP could be in same form, at least first part? > > Yeah, makes sense. > > > > + $ make <yourboardname>_defconfig > > > + $ make -j5 -s > > > +* Transfer to an uSD card (see below for more details):: > > > + > > > + $ dd if=u-boot-sunxi-with-spl.bin of=/dev/sdX bs=8k seek=1 > > > > Most, if not all, distros require root for above command, so $ -> #? I see > > that you used # below. Alternative would be to prepend command with sudo, > > which is imo more beginners friendly. > > Ah, good catch! > > > > +* Boot and enjoy! > > > + > > > +For more details, and alternative boot locations or installations, see > > below. > > > + > > > +Building Arm Trusted Firmware (TF-A) > > > +------------------------------------ > > > +Boards using a 64-bit Soc (A64, H5, H6, H616, R329) require the BL31 stage > > of > > > +the `Arm Trusted Firmware-A`_ firmware. This provides the reference > > > +implementation of secure software for Armv8-A, offering PSCI and SMCCC > > > +services. Allwinner support is fully mainlined. To build bl31.bin:: > > > + > > > + $ git clone https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git > > > + $ cd trusted-firmware-a > > > + $ make CROSS_COMPILE=aarch64-linux-gnu- PLAT=sun50i_a64 DEBUG=1 > > > + $ export BL31=$(pwd)/build/sun50i_a64/debug/bl31.bin > > > + > > > +The target platform (``PLAT=``) for A64 and H5 SoCs is sun50i_a64, for the > > H6 > > > +sun50i_h6, for the H616 sun50i_h616, and for the R329 sun50i_r329. Use:: > > > + > > > + $ find plat/allwinner -name platform.mk > > > + > > > +to find all supported platforms. `docs/plat/allwinner.rst`_ contains more > > > +information and lists some build options. > > > + > > > +Building the Crust management processor firmware > > > +------------------------------------------------ > > > +For some SoCs and boards, the integrated OpenRISC management controller can > > > +be used to provide power management services, foremost suspend to RAM. > > > +There is a community supported Open Source implementation called `crust`_, > > > +which runs on most SoCs featuring a management controller. > > > + > > > +This firmware part is optional, setting the SCP environment variable to > > > +/dev/null avoids the warning message when building without one. > > > + > > > +To build crust's scp.bin, you need an OpenRISC (or1k) cross compiler, > > then:: > > > + > > > + $ git clone https://github.com/crust-firmware/crust.git > > > + $ cd crust > > > + $ make <yourboard>_defconfig > > > + $ make CROSS_COMPILE=or1k-none-elf- scp > > > > I guess it would be good to point out that compiler prefix may not be the same > > on all distros. For example, Arch packages this compiler and proper prefix > > there is or1k-elf- which also works just fine. > > I feel I shouldn't spend too much time on this, instead just point to > crust's README. > > Thanks, > Andre > > > > > Best regards, > > Jernej > > > > > + $ export SCP=$(pwd)/build/scp/scp.bin > > > + > > > +Find a list of supported board configurations in the `configs/`_ directory. > > > + > > > +Building the U-Boot image > > > +------------------------- > > > +Find the U-Boot defconfig file for your board first. Those files live in > > > +the ``configs/`` directory; you can grep for the stub name of the devicetree > > > +file, if you know that, or for the SoC name to find the right version:: > > > + > > > + $ git grep -l MACH_SUN8I_H3 configs > > > + $ git grep -l sun50i-h6-orangepi-3 configs > > > + > > > +The `linux-sunxi`_ wiki also lists the name of the defconfig file in the > > > +respective board page. Then use this defconfig file to create the .config > > > +file, and build the image:: > > > + > > > + $ make <yourboard>_defconfig > > > + $ make -j5 > > > + > > > +For 64-bit boards, this requires either the BL31 environment variable to be > > > +set (as shown above in the TF-A build example), or it to be supplied on the > > > +build command line:: > > > + > > > + $ make BL31=/src/tf-a.git/build/sun50i_h616/debug/bl31.bin -j5 -s > > > + > > > +The same applies to the (optional) SCP firmware. > > > + > > > +The file containing everything you need is called ``u-boot-sunxi-with- > > spl.bin``, > > > +you will find it in the root folder of your U-Boot (build) tree. Except for > > > +raw NAND flash devices this very same file can be used for any boot source. > > > +It will contain the SPL image, fitted with the proper signature recognised > > by > > > +the BROM, and the required checksum. Also it will contain at least U- Boot > > > +proper, either wrapped in the legacy U-Boot image format, or in a FIT > > image. > > > +The board's devicetree is also included, either appended to the U-Boot > > proper > > > +image, or contained in the FIT image. If required by the SoC, this FIT file > > will > > > +also include the other firmware images. > > > + > > > +Installing U-Boot > > > +----------------- > > > + > > > +Installing on a (micro-) SD card > > > +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ > > > +All Allwinner SoCs will try to find a boot image at sector 16 (8KB) of > > > +an SD card, connected to the first MMC controller. To transfer the generated > > > +image to an SD card, from any Linux device (including the board itself) > > > > > with > > > +an (micro-)SD card reader, type:: > > > + > > > + # dd if=u-boot-sunxi-with-spl.bin of=/dev/sdX bs=1k seek=8 > > > + > > > +``/dev/sdx`` needs to be replaced with the block device name of the SD card > > > +reader. On some machines this could be ``/dev/mmcblkX``. > > > +Newer SoCs (starting from H3), also look at sector 256 (128KB) for the > > > +signature (after having checked the 8KB location). Installing the firmware > > > +there has the advantage of not overlapping with a GPT partition table. > > Simply > > > +replace the "``seek=8``" above with "``seek=128``". > > > + > > > +You can also use an existing (mainline) U-Boot to write to the SD card. > > > > > Load > > > +the generated U-Boot image somewhere into DRAM (via ``ext4load``, > > ``fatload``, > > > +or ``tftpboot``), then write to MMC device 0:: > > > + > > > + => fatload mmc 0:1 $kernel_addr_r u-boot-sunxi-with-spl.bin > > > + => mmc dev 0 > > > + => mmc write $kernel_addr_r 0x10 0x7f0 > > > + > > > +To use the alternative boot location on newer SoCs:: > > > + > > > + => mmc write $kernel_addr_r 0x100 0x700 > > > + > > > +Installing on eMMC (on-board flash memory) > > > +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ > > > +Some boards have a soldered eMMC chip, some other boards have an eMMC > > socket > > > +to receive an optional eMMC module. U-Boot can be installed to those chips, > > > +to boot without an SD card inserted. The Boot-ROM can boot either from the > > > +regular user data partition, or from one of the separate eMMC boot > > partitions. > > > +U-Boot can be installed either from a running Linux instance on the device, > > > +from a running (mainline) U-Boot, or via an adapter for the (removable) > > > +eMMC module. > > > + > > > +Installing on an eMMC user data partition from Linux > > > +```````````````````````````````````````````````````` > > > +If you have a running Linux instance on the device, and have somehow copied > > > +over the image file to that device, you can write the image directly into > > the > > > +eMMC device from there. > > > +Find the name of the block device file first, it is one of the > > > +``/dev/mmcblk<X>`` devices. eMMC devices typically also list a > > > +``/dev/mmcblk<X>boot0`` partition (see below), this helps you to tell it > > apart > > > +from the SD card device. > > > +To install onto the user data partition:: > > > + > > > + # dd if=u-boot-sunxi-with-spl.bin of=/dev/dev/mmcblkX bs=1k seek=8 > > > + > > > +Similar to SD cards, the BROM in newer SoCs (H3 and above) also checks > > > +sector 256 of an eMMC, so you can use "``seek=128``" as well. > > > + > > > +Installing on an eMMC boot partition from Linux > > > +``````````````````````````````````````````````` > > > +In the following examples, ``/dev/mmcblkX`` needs to be replaced with the > > block > > > +device name of the eMMC device. The eMMC device can be recognised by also > > > +listing the boot partitions (``/dev/mmcblkXboot0``) in ``/proc/ > > partitions``. > > > + > > > +To allow booting from one of the eMMC boot partitions, this one needs to be > > > +enabled first. This only needs to be done once, as this setting is > > > +persistent, even though the boot partition can be disabled or changed again > > > +any time later:: > > > + > > > + # apt-get install mmc-utils > > > + # mmc bootbus set single_hs x1 x4 /dev/mmcblkX > > > + # mmc bootpart enable 1 1 /dev/mmcblkX > > > + > > > +The first "1" in the last command points to the boot partition number to be > > > +used, typically devices offer two boot partitions. > > > + > > > +By default Linux disables write access to the boot partitions, to prevent > > > +accidental overwrites. You need to disable the write protection (until the > > > +next reboot), then can write the U-Boot image to the *first* sector of the > > > +selected boot partition:: > > > + > > > + # echo 0 > /sys/block/mmcblkXboot0/force_ro > > > + # dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblkXboot0 bs=1k > > > + > > > +Installing on an eMMC user data partition from U-Boot > > > +````````````````````````````````````````````````````` > > > +You can also write the generated image file to an SD card, boot the device > > > +from there, and burn the very same image to the eMMC device from U- Boot. > > > +The following commands copy the image from the SD card to the eMMC device:: > > > + > > > + => mmc dev 0 > > > + => mmc read $kernel_addr_r 0x10 0x7f0 > > > + => mmc dev 1 > > > + => mmc write $kernel_addr_r 0x10 0x7f0 > > > + > > > +You can also copy an image from the 8K offset of an SD card to the 128K > > > +offset of the eMMC (or any combination), just change the "``0x10 0x7f0``" > > above > > > +to "``0x100 0x700``", respectively. Of course the image file can be loaded > > via > > > +any other loading method, including ``fatload``, ``ext4load``, > > ``tftpboot``. > > > + > > > +Installing on an eMMC boot partition from U-Boot > > > +```````````````````````````````````````````````` > > > +The selected eMMC boot partition needs to be initially enabled first (same > > > +as in Linux above), you can do this from U-Boot with:: > > > + > > > + => mmc dev 1 > > > + => mmc bootbus 1 1 0 0 > > > + => mmc partconf 1 1 1 1 > > > + > > > +The first "1" in both commands denotes the MMC device number. The second "1" > > > +in the partconf command sets the required ``BOOT_ACK`` option, the last two > > "1"s > > > +selects the active boot partition and the target for the next data access, > > > +respectively. So for the next "``mmc write``" command to address one of the > > boot > > > +partitions, the last number must either be "1" or "2", "0" would switch > > > > > (back) > > > +to the normal user data partition. > > > + > > > +Then load the ``u-boot-sunxi-with-spl.bin`` image file into DRAM, either by > > > +reading directly from an SD card or eMMC user data partition, or from a > > > +file system or TFTP (see above), and transfer it to the boot partition:: > > > + > > > + => tftpboot $kernel_addr_r u-boot-sunxi-with-spl.bin > > > + => mmc write $kernel_addr_r 0 0x7f0 > > > + > > > +After that the device should boot from the selected boot partition, which > > takes > > > +precedence over booting from the user data partition. > > > + > > > +Installing on SPI flash > > > +^^^^^^^^^^^^^^^^^^^^^^^ > > > +Some devices have a SPI NOR flash chip soldered on the board. If it is > > > +connected to the SPI0 pins on PortC, the BROM can also boot from there. > > > +Typically the SPI flash has the lowest boot priority, so SD card and eMMC > > > +devices will be considered first. > > > + > > > +Installing on SPI flash from Linux > > > +`````````````````````````````````` > > > +If the devicetree enables and describes the SPI flash device, you can access > > > +the SPI flash content from Linux, using the `MTD utils`_:: > > > + > > > + # apt-get install mtd-utils > > > + # mtdinfo > > > + # mtd_debug erase /dev/mtdX 0 0xf0000 > > > + # mtd_debug write /dev/mtdX 0 0xf0000 u-boot-sunxi-with-spl.bin > > > + > > > +``/dev/mtdX`` needs to be replaced with the respective device name, as > > listed > > > +in the output of ``mtdinfo``. > > > + > > > +Installing on SPI flash from U-Boot > > > +``````````````````````````````````` > > > +If SPI flash driver and command support (``CONFIG_CMD_SF``) is enabled in > > the > > > +U-Boot configuration, the image file can be installed via U-Boot as well:: > > > + > > > + => tftpboot $kernel_addr_r u-boot-sunxi-with-spl.bin > > > + => sf probe > > > + => sf erase 0 +0xf0000 > > > + => sf write $kernel_addr_r 0 $filesize > > > + > > > +Installing on SPI flash via USB in FEL mode > > > +``````````````````````````````````````````` > > > +If the device is in FEL mode (see below), the SPI flash can also be filled > > > +with the sunxi-fel utility, via an USB(-OTG) cable from any USB host > > machine:: > > > + > > > + $ sunxi-fel -v -p spiflash-write 0 u-boot-sunxi-with-spl.bin > > > + > > > +Booting via the USB(-OTG) FEL mode > > > +---------------------------------- > > > +If none of the boot locations checked by the BROM contain a medium or valid > > > +signature, the BROM will enter the so-called FEL mode, in which it will > > > +listen to commands from a host on the SoC's USB-OTG interface. Those > > commands > > > +allow to read from and write to arbitrary memory locations, also to start > > > +execution at any address, which allows to bootstrap a board solely via an > > > +USB cable. Some boards feature a "FEL" or "U-Boot" button, which forces > > > +FEL mode despite a valid boot location being present. The same can be > > achieved > > > +via a `magic binary`_ on an SD card, which allows to enter FEL mode on any > > > +board. > > > + > > > +To use FEL booting, let the board enter FEL mode, via any of the mentioned > > > +methods (no boot media, FEL button, SD card with FEL binary), then connect > > > +a USB cable to the board's USB OTG port. Some boards (Pine64, TV boxes) > > > > > don't > > > +have a separate OTG port. In this case mostly one of the USB-A ports is > > > +connected to USB0, and can be used via a non-standard USB-A to USB-A cable. > > > + > > > +Typically there is no on-board indication of FEL mode, other than a new USB > > > +device appearing on the connected host computer. The USB vendor/device ID > > > +is 1f3a:efe8. Mostly this will identify as "sunxi SoC OTG connector in > > > +FEL/flashing mode", but older distributions might still report "Onda > > > +(unverified) V972 tablet in flashing mode". > > > + > > > +The `sunxi_fel`_ tool implements the proprietary BROM protocol, and allows > > to > > > +bootstrap U-Boot by just providing our venerable u-boot-sunxi-with- > > spl.bin:: > > > + > > > + $ sudo apt-get install sunxi-tools > > > + $ sunxi-fel -v -p uboot u-boot-sunxi-with-spl.bin > > > + > > > +Additional binaries like a kernel, an initial ramdisk or a boot script, can > > > +also be uploaded via FEL, check the Wiki's `FEL page`_ for more details. > > > + > > > +.. _`Arm Trusted Firmware-A`: https://www.trustedfirmware.org/projects/ tf-a/ > > > +.. _`docs/plat/allwinner.rst`: https://trustedfirmware-a.readthedocs.io/ en/ > > latest/plat/allwinner.html > > > +.. _`crust`: https://github.com/crust-firmware/crust > > > +.. _`configs/`: https://github.com/crust-firmware/crust/tree/master/ configs > > > +.. _`linux-sunxi`: https://linux-sunxi.org > > > +.. _`MTD utils`: http://www.linux-mtd.infradead.org/ > > > +.. _`magic binary`: https://github.com/linux-sunxi/sunxi-tools/raw/ master/ > > bin/fel-sdboot.sunxi > > > +.. _`sunxi_fel`: https://github.com/linux-sunxi/sunxi-tools > > > +.. _`FEL page`: https://linux-sunxi.org/FEL/USBBoot > > > -- > > > 2.17.6 > > > > > > > > > > > > > >
