Resyc DTS files with Linux 5.17-rc5.
Signed-off-by: Adam Ford <[email protected]>
diff --git a/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts
b/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts
index 7675bc3fa8..cb08aa62d9 100644
--- a/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts
+++ b/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts
@@ -9,5 +9,13 @@
/ {
model = "LogicPD Zoom OMAP35xx Torpedo Development Kit";
- compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3";
+ compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3430", "ti,omap3";
+};
+
+&omap3_pmx_core {
+ isp1763_pins: pinmux_isp1763_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP |
MUX_MODE4) /* sdmmc1_dat6.gpio_128 */
+ >;
+ };
};
diff --git a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts
b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts
index 18c27e8505..07ea822fe4 100644
--- a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts
+++ b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts
@@ -50,6 +50,20 @@
};
};
+&uart2 {
+ /delete-property/dma-names;
+ bluetooth {
+ compatible = "ti,wl1283-st";
+ enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio 162 */
+ max-speed = <3000000>;
+ };
+};
+
+/* The DM3730 has a faster L3 than OMAP35, so increase pixel clock */
+&mt9p031_out {
+ pixel-clock-frequency = <90000000>;
+};
+
&omap3_pmx_core {
mmc3_pins: pinmux_mm3_pins {
pinctrl-single,pins = <
@@ -71,3 +85,12 @@
>;
};
};
+
+/* The gpio muxing between omap3530 and dm3730 is different for GPIO_128 */
+&omap3_pmx_wkup {
+ isp1763_pins: pinmux_isp1763_pins {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a58, PIN_INPUT_PULLUP | MUX_MODE4)
/* reserved.gpio_128 */
+ >;
+ };
+};
diff --git a/arch/arm/dts/logicpd-torpedo-baseboard.dtsi
b/arch/arm/dts/logicpd-torpedo-baseboard.dtsi
index 642e809e75..b4664ab002 100644
--- a/arch/arm/dts/logicpd-torpedo-baseboard.dtsi
+++ b/arch/arm/dts/logicpd-torpedo-baseboard.dtsi
@@ -65,6 +65,7 @@
pinctrl-0 = <&pwm_pins>;
ti,timers = <&timer10>;
#pwm-cells = <3>;
+ ti,clock-source = <0x01>;
};
};
@@ -80,6 +81,8 @@
};
&mcbsp2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcbsp2_pins>;
status = "okay";
};
@@ -90,7 +93,8 @@
&gpmc {
ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */
- 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */
+ 1 0 0x2c000000 0x1000000 /* CS1: 16MB for LAN9221 */
+ 6 0 0x28000000 0x1000000>; /* CS6: 16MB for ISP1763 */
ethernet@gpmc {
pinctrl-names = "default";
@@ -99,16 +103,60 @@
interrupts = <1 IRQ_TYPE_LEVEL_LOW>; /* gpio129 */
reg = <1 0 0xff>;
};
+
+ usb@6,0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&isp1763_pins>;
+ compatible = "nxp,usb-isp1763";
+ reg = <0x6 0x0 0xff>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "host";
+ bus-width = <16>;
+ dr_mode = "host";
+ gpmc,mux-add-data = <0>;
+ gpmc,device-width = <2>;
+ gpmc,wait-pin = <0>;
+ gpmc,burst-length = <4>;
+ gpmc,cycle2cycle-samecsen = <1>;
+ gpmc,cycle2cycle-diffcsen = <1>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <45>;
+ gpmc,cs-wr-off-ns = <45>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <0>;
+ gpmc,adv-wr-off-ns = <0>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <45>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <25>;
+ gpmc,rd-cycle-ns = <60>;
+ gpmc,wr-cycle-ns = <45>;
+ gpmc,access-ns = <35>;
+ gpmc,page-burst-access-ns = <0>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <60>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wr-data-mux-bus-ns = <5>;
+ gpmc,wr-access-ns = <20>;
+ };
};
+&hdqw1w {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdq_pins>;
+};
+
+
&vpll2 {
regulator-always-on;
};
&dss {
- status = "ok";
+ status = "okay";
vdds_dsi-supply = <&vpll2>;
- vdda_video-supply = <&video_reg>;
+ vdda_video-supply = <&vpll2>;
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins1>;
port {
@@ -124,44 +172,19 @@
display0 = &lcd0;
};
- video_reg: video_reg {
- pinctrl-names = "default";
- pinctrl-0 = <&panel_pwr_pins>;
- compatible = "regulator-fixed";
- regulator-name = "fixed-supply";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */
- };
-
lcd0: display {
- compatible = "panel-dpi";
+ /* This isn't the exact LCD, but the timings meet spec */
+ compatible = "newhaven,nhd-4.3-480272ef-atxl";
label = "15";
- status = "okay";
- /* default-on; */
pinctrl-names = "default";
-
+ pinctrl-0 = <&panel_pwr_pins>;
+ backlight = <&bl>;
+ enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
port {
lcd_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
-
- panel-timing {
- clock-frequency = <9000000>;
- hactive = <480>;
- vactive = <272>;
- hfront-porch = <3>;
- hback-porch = <2>;
- hsync-len = <42>;
- vback-porch = <3>;
- vfront-porch = <4>;
- vsync-len = <11>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
};
bl: backlight {
@@ -193,6 +216,12 @@
>;
};
+ hdq_pins: hdq_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE0)
/* hdq_sio */
+ >;
+ };
+
pwm_pins: pinmux_pwm_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT |
PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */
diff --git a/arch/arm/dts/logicpd-torpedo-som.dtsi
b/arch/arm/dts/logicpd-torpedo-som.dtsi
index 3fdd0a72f8..3a5228562b 100644
--- a/arch/arm/dts/logicpd-torpedo-som.dtsi
+++ b/arch/arm/dts/logicpd-torpedo-som.dtsi
@@ -35,6 +35,11 @@
};
};
+/* The Torpedo doesn't route the USB host pins */
+&usbhshost {
+ status = "disabled";
+};
+
&gpmc {
ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
@@ -192,3 +197,7 @@
&twl_gpio {
ti,use-leds;
};
+
+&twl_keypad {
+ status = "disabled";
+};
--
2.34.1
