[PATCH 1/6] net: zynq_gem: Use shared MDIO bus support for zynqmp

[Michal Simek]

CONFIG_ETH_PHY enables support to utilize generic ethernet phy
framework. Though if ethernet PHY node is in other ethernet node, it
will use shared MDIO to access the PHY of other ethernet.

Signed-off-by: Michal Simek <michal.si...@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.re...@xilinx.com>
---

 drivers/net/zynq_gem.c | 32 +++++++++++++++++++++++---------
 1 file changed, 23 insertions(+), 9 deletions(-)

diff --git a/drivers/net/zynq_gem.c b/drivers/net/zynq_gem.c
index 3118d1472669..168aabbdd006 100644
--- a/drivers/net/zynq_gem.c
+++ b/drivers/net/zynq_gem.c
@@ -33,6 +33,7 @@
 #include <linux/bitops.h>
 #include <linux/err.h>
 #include <linux/errno.h>
+#include <eth_phy.h>
 
 /* Bit/mask specification */
 #define ZYNQ_GEM_PHYMNTNC_OP_MASK      0x40020000 /* operation mask bits */
@@ -321,6 +322,9 @@ static int zynq_phy_init(struct udevice *dev)
        /* Enable only MDIO bus */
        writel(ZYNQ_GEM_NWCTRL_MDEN_MASK, &regs_mdio->nwctrl);
 
+       if (IS_ENABLED(CONFIG_DM_ETH_PHY))
+               priv->phyaddr = eth_phy_get_addr(dev);
+
        priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
                                   priv->interface);
        if (!priv->phydev)
@@ -771,14 +775,22 @@ static int zynq_gem_probe(struct udevice *dev)
                }
        }
 
-       priv->bus = mdio_alloc();
-       priv->bus->read = zynq_gem_miiphy_read;
-       priv->bus->write = zynq_gem_miiphy_write;
-       priv->bus->priv = priv;
+       if (IS_ENABLED(CONFIG_DM_ETH_PHY))
+               priv->bus = eth_phy_get_mdio_bus(dev);
 
-       ret = mdio_register_seq(priv->bus, dev_seq(dev));
-       if (ret)
-               goto err2;
+       if (!priv->bus) {
+               priv->bus = mdio_alloc();
+               priv->bus->read = zynq_gem_miiphy_read;
+               priv->bus->write = zynq_gem_miiphy_write;
+               priv->bus->priv = priv;
+
+               ret = mdio_register_seq(priv->bus, dev_seq(dev));
+               if (ret)
+                       goto err2;
+       }
+
+       if (IS_ENABLED(CONFIG_DM_ETH_PHY))
+               eth_phy_set_mdio_bus(dev, priv->bus);
 
        ret = zynq_phy_init(dev);
        if (ret)
@@ -841,8 +853,10 @@ static int zynq_gem_of_to_plat(struct udevice *dev)
                ofnode parent;
 
                debug("phy-handle does exist %s\n", dev->name);
-               priv->phyaddr = ofnode_read_u32_default(phandle_args.node,
-                                                       "reg", -1);
+               if (!(IS_ENABLED(CONFIG_DM_ETH_PHY)))
+                       priv->phyaddr = ofnode_read_u32_default
+                                       (phandle_args.node, "reg", -1);
+
                priv->phy_of_node = phandle_args.node;
                priv->max_speed = ofnode_read_u32_default(phandle_args.node,
                                                          "max-speed",
-- 
2.35.1