On 4/22/22 21:39, Pali Rohár wrote:
> On Friday 22 April 2022 21:32:54 Jaehoon Chung wrote:
>> On 4/5/22 01:33, Pali Rohár wrote:
>>> QorIQ pre-PBL BootROM scans first 24 SD card sectors (each with fixed 512
>>> bytes length) for boot signature. Implement same redundancy behavior in
>>> fsl_esdhc_spl driver to allow loading proper U-Boot when boot sector is not
>>> the first one.
>>>
>>> Signed-off-by: Pali Rohár <[email protected]>
>>> ---
>>> drivers/mmc/fsl_esdhc_spl.c | 25 ++++++++++++++++++-------
>>> 1 file changed, 18 insertions(+), 7 deletions(-)
>>>
>>> diff --git a/drivers/mmc/fsl_esdhc_spl.c b/drivers/mmc/fsl_esdhc_spl.c
>>> index 0146a231b221..ea8f4cd66964 100644
>>> --- a/drivers/mmc/fsl_esdhc_spl.c
>>> +++ b/drivers/mmc/fsl_esdhc_spl.c
>>> @@ -20,7 +20,6 @@
>>> #define ESDHC_BOOT_IMAGE_ADDR 0x50
>>> #define MBRDBR_BOOT_SIG_55 0x1fe
>>> #define MBRDBR_BOOT_SIG_AA 0x1ff
>>> -#define CONFIG_CFG_DATA_SECTOR 0
>>>
>>>
>>> void mmc_spl_load_image(uint32_t offs, unsigned int size, void *vdst)
>>> @@ -62,11 +61,13 @@ void __noreturn mmc_boot(void)
>>> #ifndef CONFIG_FSL_CORENET
>>> uchar *tmp_buf;
>>> u32 blklen;
>>> + u32 blk_off;
>>> uchar val;
>>> #ifndef CONFIG_SPL_FSL_PBL
>>> u32 val32;
>>> #endif
>>> uint i, byte_num;
>>> + u32 sector;
>>> #endif
>>> u32 offset, code_len;
>>> struct mmc *mmc;
>>> @@ -86,30 +87,37 @@ void __noreturn mmc_boot(void)
>>> offset = CONFIG_SYS_MMC_U_BOOT_OFFS;
>>> #else
>>> blklen = mmc->read_bl_len;
>>> + if (blklen < 512)
>>> + blklen = 512;
>>> tmp_buf = malloc(blklen);
>>> if (!tmp_buf) {
>>> puts("spl: malloc memory failed!!\n");
>>> hang();
>>> }
>>> +
>>> + sector = 0;
>> Why does it assign to 0 at here? Doesn't initialize this at above?
> All variables in this file are initialized after declaration. So I used
> this same coding style also for newly introduced variables.
>
>> Does it need to check whether CONFIG_SPL_FSL_PBL enabled or not?
> This redundancy (retry) is implemented only for pre-PBL BootROMs (when
> CONFIG_SPL_FSL_PBL is not enabled). I do not know how it works in PBL
> BootROMs, so PBL code scans only sector 0, like before.
It's my mistake. I didn't see "#else" for CONFIG_FSL_CORENET. Discard previous
my comment.
Beet Regards,
Jaehoon Chung
>
>> Best Regards,
>> Jaehoon Chung
>>
>>> +again:
>>> memset(tmp_buf, 0, blklen);
>>>
>>> /*
>>> * Read source addr from sd card
>>> */
>>> - err = mmc->block_dev.block_read(&mmc->block_dev,
>>> - CONFIG_CFG_DATA_SECTOR, 1, tmp_buf);
>>> + blk_start = (sector * 512) / mmc->read_bl_len;
>>> + blk_off = (sector * 512) % mmc->read_bl_len;
>>> + blk_cnt = DIV_ROUND_UP(512, mmc->read_bl_len);
>>> + err = mmc->block_dev.block_read(&mmc->block_dev, blk_start, blk_cnt,
>>> tmp_buf);
>>> if (err != 1) {
>>> puts("spl: mmc read failed!!\n");
>>> hang();
>>> }
>>>
>>> #ifdef CONFIG_SPL_FSL_PBL
>>> - val = *(tmp_buf + MBRDBR_BOOT_SIG_55);
>>> + val = *(tmp_buf + blk_off + MBRDBR_BOOT_SIG_55);
>>> if (0x55 != val) {
>>> puts("spl: mmc MBR/DBR signature is not valid!!\n");
>>> hang();
>>> }
>>> - val = *(tmp_buf + MBRDBR_BOOT_SIG_AA);
>>> + val = *(tmp_buf + blk_off + MBRDBR_BOOT_SIG_AA);
>>> if (0xAA != val) {
>>> puts("spl: mmc MBR/DBR signature is not valid!!\n");
>>> hang();
>>> @@ -123,10 +131,13 @@ void __noreturn mmc_boot(void)
>>> byte_num = 4;
>>> val32 = 0;
>>> for (i = 0; i < byte_num; i++) {
>>> - val = *(tmp_buf + ESDHC_BOOT_SIGNATURE_OFF + i);
>>> + val = *(tmp_buf + blk_off + ESDHC_BOOT_SIGNATURE_OFF + i);
>>> val32 = (val32 << 8) + val;
>>> }
>>> if (val32 != ESDHC_BOOT_SIGNATURE) {
>>> + /* BOOT signature may be on the first 24 sectors (each being
>>> 512 bytes) */
>>> + if (++sector < 24)
>>> + goto again;
>>> puts("spl: mmc BOOT signature is not valid!!\n");
>>> hang();
>>> }
>>> @@ -135,7 +146,7 @@ void __noreturn mmc_boot(void)
>>> byte_num = 4;
>>> offset = 0;
>>> for (i = 0; i < byte_num; i++) {
>>> - val = *(tmp_buf + ESDHC_BOOT_IMAGE_ADDR + i);
>>> + val = *(tmp_buf + blk_off + ESDHC_BOOT_IMAGE_ADDR + i);
>>> offset = (offset << 8) + val;
>>> }
>>> offset += CONFIG_SYS_MMC_U_BOOT_OFFS;
